Denver SEL-10350 ODIN Electric Scooter User Manual

About the Product

Important! This electric scooter must be charged and stored safely. For battery health and safety, avoid charging in temperatures below 5°C or above 45°C. Always disconnect the power cable once fully charged and use only the supplied power adapter. Ensure all screws are tightened to prevent unsafe situations. If riding in wet conditions, dry the pedal board thoroughly afterward.

WARNING: Ensure the steering system is correctly adjusted and all connection components are secure and unbroken before riding. Read the operation guide and warnings for correct techniques. Always wear shoes. Self-locking nuts and fixings can lose effectiveness over time. Modifications to any parts or materials of the electric scooter are not allowed.

1.1 Technical Modifications

Avoid removing components or making technical modifications to preserve the scooter's condition. Specifically, do not modify the following systems: Powertrain, Battery, Braking, Steering, Lighting, Electrical, Wheel equipment, Tyre equipment, Anti-slip equipment.

Maintenance should be conducted by certified agents.

1.2 Traffic Rules

• Do not ride if under 14 years of age.
• Do not ride with more than one person.
• Maximum speed: 20 km/h.
• Valid liability insurance is required.
• Do not ride under the influence of drugs, alcohol, or medicine.
• Do not ride if physical or mental condition is inadequate.
• Always adhere to applicable traffic rules and stay informed about changes.
• Be considerate of weaker road users.
• Adapt speed to traffic and road conditions.
• Never obstruct or endanger pedestrians.
• Do not ride on pedestrian-only routes or routes restricted for bicycles.
• Do not ride on routes reserved for cars/vans/trucks/motorcycles.

Product and Accessories

The electric scooter features a throttle, bell, display, electric brake, disc brakes, front and back lights, front shock absorption, and a foldable mechanism. It has 10" wheels.

Included accessories are a charger, four screws for handlebar attachment, and four Allen keys.

Unfolding and Folding the Scooter

Unfolding

1. Place the scooter on its wheels and unlock the handlebar hook.
2. Pull up the handle gently and slowly, then close the lock lever on the lower part of the handlebar support tube.
3. The scooter is unfolded when the rod clicks into place.

Folding

1. Release the release lever on the lower part of the handlebar support tube.
2. Fully open the release lever.
3. Lower the handlebar tube downwards to fold the scooter.
4. Hook the folded tube onto the appropriate support.

Assembling the Device

Before use, install the handlebar onto the main vehicle frame.

1. Insert the handlebar into the vehicle frame.
2. Align the holes in the handlebar with those in the frame. Insert and tighten four screws securely, repeating for the opposite side.
3. Mount the front K-light: Install it into the light bracket and use an Allen key to fix the screw and nut.

Charging the Scooter

Connect the supplied power adapter to the electric scooter's charging port.

Intended Use

This electric scooter is designed for personal entertainment and domestic use. It is suitable for individuals aged 14 and above, with a technically permissible total weight of 120kg (scooter weight is 16.5kg). Operation requires good visibility and adequate physical stability. Operators must wear specified personal protective equipment.

Safety Instruction

Always wear a helmet and protective gear (elbow, knee, wrist protectors) for personal safety. Read the manual carefully to ensure safe and enjoyable riding. Comply with all local regulations. Ride safely, at a speed that allows for prompt braking, and be considerate of others. If lending the scooter, ensure the user has protective gear and knows how to ride it. Before riding, check all parts for proper function. Contact your retailer for service if any issues are detected; do not attempt self-repair. Inspect rear tire, brake, and pad regularly. Avoid excessive force on the rear fender. Avoid constant braking, as it wears tires and heats the motor. If unusual noises or vibrations occur, a bearing may be damaged; contact your retailer. Ride only on dry surfaces. Do not ride on long or steep slopes. Stop riding upon receiving a "Low Battery Warning" and use the rear brake. Do not use the electric brake and throttle simultaneously. Contact customer service for any operational issues.

Maintenance

Regular maintenance is crucial for optimal performance.

• Battery Maintenance: Charge at regular intervals, even when not in use, to prevent damage from low voltage. Avoid draining the battery completely; charge while it has some power. Battery life decreases over time. Performance may be lower in extreme temperatures. A fully charged battery holds power for 90-120 days. Keep the battery within -10°C to 50°C. Use only the original charger. Do not overcharge or discharge. Do not disassemble the battery package; this is for professionals only.
• Bearings, Screws, Brakes and Wheels: The scooter has sealed, dustproof bearings requiring no lubrication. Check bearings for wear. Avoid jumping on/off or applying excessive force. Ensure all screws are tight. Check brakes for wear and adjust/replace as needed. Check wheels for wear.
• Storage and Cleaning: Clean with a damp cloth; avoid high-pressure water. Toothpaste can help with stubborn dirt. Ensure the scooter is off and the charging input is covered during cleaning. Dry thoroughly. Do not use solvents like alcohol or gas. Store in a dry, cool environment, away from direct sunlight or heat.

Operational Control

9.1 Control and Display

The display shows speed and gear level. Front/Back K-Lights and battery level are also indicated.

9.2 Button and Speed Transfer

Press the "Power" button for 5 seconds to turn the scooter on. Press it once to toggle the Front/Back K-Light. Press "Power" twice consecutively to switch between speed gears: ECO (6 KM/H), D (15 KM/H), S (20 KM/H).

Electric Scooter Riding

1. Press "Power" buttons to adjust speed level.
2. Manually push off with your foot before the accelerator button works. Press the accelerator to move.
3. Press the Electric brake or Disc brake to stop.
4. Pressing the accelerator and electric brake simultaneously will automatically brake.
5. Use the rear wheel brake system for high-speed riding.
6. At night, press the headlight switch to turn on the headlight.

10.1 Front and Back K- Light

Press the key to turn ON the power; headlights and taillights will be ON. Press the key to turn OFF the power; headlights and taillights will go out.

List of Parameters

Electric scooter details: Model: SEL-10350 ODIN. Input: 100V-240V~, 50/60Hz, 2.5A(Max). Output: 42V 2A. Max Speed: 20km/h. Weight: 17.5kg. Year of manufacture: 2021. Technically permissible total weight: 120kg. Battery: 36V/10Ah. Power Consumption: ≤ 350W. Use charger XHK-800B-4220. Manufacturer: DENVER ELECTRONICS A/S, Omega 5A Soeften DK-8382 Hinnerup, Denmark. Website: www.denver-electronics.com

Electric Scooter Safe Parking

Once stopped, dismount and use your right foot to push the side stand down (located on the left-hand side below the foot board) to support the scooter. Push the side stand back up to be parallel with the foot board before riding again.

Safe Transportation

Pack the electric scooter flat. Do not drop it during transportation and keep it away from fire or explosive materials.

Warnings

14.1 Risks of Riding

WARNING: Learn safe riding before riding at speed. Failure to observe rules, loss of control, falls, and violations can cause injuries. Speed and range depend on rider weight, terrain, temperature, and style. Wear a helmet and protective clothing. Read instructions carefully. Use only in dry environments. Ensure compliance with local regulations. For domestic use only.

14.2 Preparation

• Charge the battery completely.
• Wear a helmet, knee and elbow pads, and ear protection.
• Avoid loose clothing or open laces that can get caught in wheels.

14.3 Weight Restriction

Reason for weight restriction: Ensuring rider safety and avoiding overload damage. Technically permissible total weight: 120kg (includes scooter weight of 17.5kg).

WARNING: Do not try to make a turn too fast.

WARNING: Lithium battery inside.

WARNING: If the scooter switches off, it will block automatically. Release by pressing On/Off. Use only at temperatures between -10°C and +45°C.

14.4 Range per Charge

Range is affected by: Topography (level paths offer greater range), Rider's weight, Temperature (extreme temperatures reduce range), Maintenance (proper charging and battery condition extend range), Speed and riding style (constant speed is better than frequent stops/starts).

14.5 Safe Riding

Familiarize yourself with the vehicle for sound condition. Observe all safety instructions. The scooter is for personal entertainment; avoid public roads/road traffic. Children under 14 and people with balance issues should not ride. Avoid riding under the influence of alcohol or other substances.

• Do not carry objects while riding.
• Ensure clear forward vision.
• Keep feet on the foot board.
• The scooter accommodates only one person.
• Do not start or stop abruptly.
• Avoid riding on steep slopes.
• Stop if you hit a solid object.
• Do not ride in dimly lit or dark places.
• Ride at your own risk; no liability for accidents/damage.
• Ride at a safe speed for stopping.
• Maintain sufficient distance from others.
• Steer through balance shifting; fast movement can cause falls.
• Do not ride in rain or wet conditions; ride only in dry weather.
• Avoid riding over obstacles, snow, ice, or slippery surfaces.
• Avoid riding over textiles, small branches, and stones.
• Avoid riding in narrow or obstructed places.
• Jumping on/off or "trick riding" can cause damage not covered by warranty and carries injury risk.

14.6 Charging

• Ensure scooter, charger, and DC input are dry.
• Use ONLY the supplied charger XHK-800B-4220 (42V – 2A). Using other chargers may cause damage.
• Never charge unsupervised.
• Charging period should not exceed four hours.
• Charge and use between 0°C and 45°C.
• Store between 0°C and 35°C (optimum 25°C).
• Charge and store away from flammable materials, sunlight, or open flames.
• Allow to cool for one hour after use before charging.
• If left with others, charge partially (20-50%).
• The device is shipped partially charged; keep it that way until use.
• Allow scooter to cool for at least 1 hour before packaging.

CAUTION: Do not use the electric scooter during charging. The charger's LED is red during charging and green when complete. Disconnect charger after charging.

CAUTION: Connect the DC cable only to the DC input. Do not insert foreign objects. Do not remove the protective cap from the DC input except when charging. Re-cap after charging.

WARNING: Prevent liquids from entering the scooter's inner components to avoid permanent damage and injury risk.

CAUTION: Do not open the electric scooter casing; this invalidates the warranty.

WARNING: Wear helmet and protective clothing before using the electric scooter.

• Read manual carefully before use.
• Use only on dry and level ground.
• For domestic use only.
• Not for use by anyone under 14 years of age.

Declaration of Conformity

DENVER ELECTRONICS A/S certifies that the design and manufacturing of the DENVER SEL-10350 ODIN Electric scooter conforms to Machinery Directive 2006/42/EC and other relevant standards (EN ISO 12100:2010, EN 60335-1:2012+A11:2014+A13:2017), and complies with essential requirements of the Machine Directive, MD 2006/42/EC, LVD 2014/35/EU, and EMC 2014/30/EU. Authorized signatory: Torben Balmer, CEO.

Environmental Information

Electric and electronic equipment, including batteries, may contain hazardous materials. Dispose of waste correctly according to regulations, separating it from household waste. Utilize designated collection points for recycling.

DENVER ELECTRONICS A/S, Omega 5A, Soeften, DK-8382 Hinnerup, Denmark. www.denver-electronics.com

Regarding Battery Charging SEL-10350 ODIN

Important – Please read! The battery is not fully charged from the factory and may discharge slowly. If the scooter does not turn on or charge (charger light is instantly green), try the following:

1. Leave the charger connected for 6-7 hours for a full charge (may take 3-4 hours to start normal charging).
2. If the issue persists, ride the scooter manually for about 100m without turning it on, then connect the charger. This helps activate the charging function, resulting in a full charge in approximately 3 hours.

For the electronic version of the manual, visit: www.denver-electronics.com.

Warnings Summary

Product names: SEL-10350 ODIN. Product type: Electric scooter. Year of manufacturing: 2021.

• Use ONLY the supplied charger XHK-800B-4220 (42V – 2A).
• Never charge unsupervised.
• Charging period should not exceed four hours.
• Charge and use between 0°C and 45°C.
• Store between 0°C and 35°C (optimum 25°C).
• Charge and store away from flammable materials, sunlight, or open flames.
• Allow to cool for one hour after use before charging.
• If left with others, charge partially (20-50%).
• Keep partially charged until use.

DENVER ELECTRONICS A/S, Omega 5A, Soeften, 8382 Hinnerup, Denmark. www.denver-electronics.com