Memphis Audio VIV60V2 SixFive Series Coaxial Speakers
Designed and Developed in the United States
Features
- Cast aluminum Six Five Series basket
- Dual layer composite fiber cone
- Tuned surround for extra flat response
- Versatile crossover settings
- Audiophile grade features and performance
- Silk tweeter
- Grill included
Specifications
| Parameter | Value |
|---|---|
| Size | 6.5" |
| RMS/PEAK (W) | 75/150 |
| Sensitivity (dB) | 90 |
| Magnet Size (oz) | 20 |
| Mounting Depth (in) | 2.95 |
Technical Details
Woofer
| Parameter | Value |
|---|---|
| Nominal Diameter | 6.49 in // 165mm |
| Driver mounting depth | 2.91 in // 74mm |
| Speaker weight | 1520 g |
| Basket Material | ALUMINUM |
| Magnet height | .71 in // 18 mm |
| Magnet diameter | 3.93 x 1.77 x 7.1 in // 100 x 45 x 18 mm |
| Magnet weight | 20 OZ |
Woofer Electrical Information
| Parameter | Value |
|---|---|
| Voice Coil Diameter | 1.18 in // 30 mm |
| Voice Coil Former Material | KSV |
| Voice Coil Nominal Impedance | 2 OHM |
| Cone Material | Fiberglass & Foam Composite |
| Surround Material | Rubber |
Tweeter Technical Information
| Parameter | Value |
|---|---|
| Dome Material | Silk |
| Dome Diameter | 1.45 in // 37 mm |
| Voice Coil Diameter | .98 in // 25 mm |
Crossover Technical Information
| Parameter | Value |
|---|---|
| Crossover Type | 2WAY |
| Tweeter Settings | +3dB/0dB/-3dB |
| Tweeter Crossover Slope | 12dB |
| Tweeter Crossover Frequency | 4800Hz |
| Woofer Crossover Slope | 6dB/12dB |
| Woofer Crossover Frequency | 4800 Hz |
Installation
General Advice
Prior to setting up your audio system, disconnecting the negative battery terminal from your vehicle is advised. Prior to cutting or drilling screws, please take time to check clearances on both sides of the mounting surface. Be mindful of any potential obstacles such as window tracks and motors. Some vehicles are not symmetrical, making it imperative to double-check both sides of the vehicle.
Crossover Network Mounting
Always mount your crossovers in a location free from moisture and away from moving parts. Crossovers should not be mounted inside door compartments if possible, as doors are not always watertight and moisture may damage your crossover. Your crossover must be connected as shown in this manual; failure to follow these connections may void your warranty and potentially damage your system and vehicle. Failure to properly install the crossovers may void your warranty. If you are uncomfortable with any of the installation steps, it is advised that you contact your local Memphis Audio dealer.
Speaker Installation
SixFive Series coaxial speakers are designed to elevate your audio system to new heights. The flawless sound reproduction from our SixFive Series is unmatched. The dual layer composite fiber material used in our cones is extremely lightweight and rigid, allowing for exceptionally accurate and powerful bass response. The silk dome tweeter centered in the swivel mount housing produces studio-quality highs that bring your music to life. Speakers are designed to elevate your audio system beyond your expectations.
Wiring Diagram Description
The wiring diagram illustrates the connection of the Memphis Audio VIV60V2 coaxial speakers to an amplifier via crossovers. It depicts an example setup using an amplifier (labeled VIV200.2) connected to Left and Right Crossovers. Each crossover then splits the audio signal to separate terminals for the Woofer (+ WF -) and Tweeter (+ TW -). While the VIV60V2 are coaxial speakers, meaning the woofer and tweeter are integrated into a single unit, this diagram shows the conceptual signal path to these distinct driver types.
Amplifier Connections (Example):
+12V: Power inputGND: Ground connectionREM: Remote turn-onPOWER: Power indicatorINPUT: Signal input (e.g., from head unit)OUTPUT: Signal output (e.g., to other amplifiers)LEVEL: Input sensitivity adjustment
Crossover Connections:
- Input from amplifier
- Output to Woofer (
+ WF -) - Output to Tweeter (
+ TW -)
Speaker Connections:
- Left Speaker: Woofer (
+,-), Tweeter (+,-) - Right Speaker: Woofer (
+,-), Tweeter (+,-)
Crossover Adjustments
Tweeter Adjustment (+/- 3 dB)
The crossover features switches to adjust the tweeter output level. Options include +3dB, 0dB, and -3dB relative to the default setting. This allows users to fine-tune the high-frequency response to their preference and vehicle acoustics.
Graphical Representation: A graph shows three distinct curves representing the tweeter's frequency response at 5kHz, 10kHz, and 20kHz for each of the three settings (+3dB, 0dB, -3dB).
Woofer Crossover Slope (6dB/12dB)
Users can select the crossover slope for the woofer between 6dB per octave and 12dB per octave. This affects how the woofer's output rolls off as frequency increases, influencing the blend with the tweeter.
Graphical Representation: A graph illustrates the woofer's frequency response with two curves, one for the 6dB slope and one for the 12dB slope, showing the attenuation at frequencies above the crossover point (e.g., 5kHz, 10kHz, 20kHz).
Warranty Information
Limited Warranty
Memphis Car Audio offers a limited warranty on Memphis Car Audio products.
Length of Warranty
- SixFive Series Component Speakers: 2 Year. (Extensions may be available through installing dealer).
What Is Covered
- Applies only to products sold to consumers by Authorized Memphis Car Audio Dealers in the United States or its possessions.
- Covers the original purchaser.
- Requires a copy of the original receipt (consumer name, dealer name, product, date of purchase).
- Defective products will be repaired or replaced at Memphis Car Audio's discretion.
What Is Not Covered
- Damage from accident, abuse, improper operation/installation, water, theft, shipping.
- Costs related to removal or re-installation.
- Service performed by unauthorized personnel.
- Products with defaced, altered, or removed serial numbers.
- Subsequent damage to other components.
- Products not purchased from an authorized dealer.
Limit on Implied Warranties
Implied warranties (fitness for use, merchantability) are limited to the duration of the express warranty. Some states may not allow these limitations.
EU Warranty
Product meets current EU warranty requirements. See Authorized dealer for details.
How To Obtain Service
Contact the Authorized Memphis Car Audio Dealer where the product was purchased. For further assistance, call 1-800-489-2300 for Memphis Car Audio's Customer Service.
Return Authorization (RA#) is required for all returns to Memphis Car Audio's warranty facility. No product will be accepted without an RA#.
Customer is responsible for shipment to Memphis Car Audio. Repaired/replaced product will be returned freight prepaid.
For more information, visit: WWW.MEMPHISCARAUDIO.COM
