Summer Infant Main Street Safety Gate

Please read the following instructions carefully. Keep this instruction manual for future reference.

Tools required: Phillips head screwdriver, drill (for top of stair installation), and pencil (not included), wrench (included).

For use with children from 6 - 24 months.

Keep small parts away from children.

Adult assembly required.

Fits openings from 29.5" - 53" wide.

Text "Install Main" to 38344 for a step-by-step installation video.

Have questions? We're here to help. For technical support please contact us at 401-671-6551 or www.summerinfant.com/contact.

WARNING

• Children have died or been seriously injured when gates are not securely installed. ALWAYS install and use gate as directed using all required parts.
• STOP using when a child can climb over or dislodge the gate.
• Use only with the locking/latching mechanism securely engaged.
• To prevent falls, never use at top of stairs without wall mounting cups and door stopper.
• NEVER use to keep child away from pool.
• NEVER leave child unattended.
• Always close and lock the gate behind you.
• This product will not necessarily prevent all accidents.
• Do not use if any components are missing or damaged.
• Adult assembly required. Exercise care when unpacking and assembling product.

CAUTION: KEEP SMALL PARTS OUT OF CHILD'S REACH.

IMPORTANT – Read the instructions carefully before use and keep them for future reference.

Components:

• A: Gate Door
• B: Gate Frame
• C: Large Extension Frame 1
• D: Large Extension Frame 2
• E: Small Extension Frame
• F: Top Latch
• G: Lower Latch
• H: Door Stop
• I: Tension Bolts with Tension Nuts (4)
• J: Adhesive Mounting Pads (4)
• K: Wall Cups (4)
• L: Wall Anchors (4)
• M: Screws (4)
• N: Wrench

Hardware:

• I (x4)
• J (x4)
• K (x4)
• L (x4)
• M (x4)
• N (x4)

Gate Configurations (Choose which best fits your scenario):

Measure the width of the opening where you intend to install the gate. Refer to the following illustrations to determine the correct installation configuration. Baseboard molding may change which configuration is appropriate.

Configuration A: (29.5" - 33") without extension frames

Configuration B: (33.5" - 37") with small extension frame

Configuration C: (37.5" - 41") with large extension frame

Configuration D: (41.5" - 45") with large and small extension frame

Configuration E: (45.5" - 49") with 2 large extension frames

Configuration F: (49.5" - 53") with the 2 large and 1 small extension frames

Note: This instruction book illustrates installation of gate configuration F. If choosing gate configuration A, skip ahead to step 2. Otherwise, follow step 1 using the appropriate extension frames that best fit your scenario.

Important: Gate includes a door stop (part H) which prevents the gate from swinging open in one direction. When installing the gate at the top of stairs, be sure that the door stop is on the stairway side of the gate so the door cannot open over the stairs. While the door stop comes assembled on the gate, it can be removed and installed on either side of the gate frame.

When gate is not used at top of stairs, door stop may be removed to allow gate door to open in either direction.

WARNING: NEVER install three extension frames on the same side of the gate.

Installation:

1. Connect the extension frames to the gate frame by inserting the extension pins into the holes in the extension frame, or into the gate frame (if extensions are not being used).
2. Slide tension bolts into upper and lower holes on both sides of extension frames (or gate frame if no extensions are being used).
3. Stand the gate in the center of the opening. Make sure the bottom of the gate is completely flush to the floor. Slide tension bolts out until they contact the door frame or wall on both sides.

IMPORTANT: Check locations A and B. The distance between the gate and the wall should never exceed 2.75".

Use the tension nuts to tighten both of the bottom tension bolts.

Use the tension nuts to tighten both of the top tension bolts.

Note: If mounting at top of stairs, proceed to step 6. Otherwise, follow the directions in step 14 to tighten the tension nuts.

STOP! Wall Cup/Top of Stairs Installation:

WARNING: For use at top of stairs, wall cup installation is MANDATORY.

Follow these wall cup installation instructions when using gate at TOP OF STAIRS (MANDATORY), or if using wall cups for a standard opening (optional). If opting not to use wall cups for a standard opening, skip ahead to step 14.

Use the pencil to trace the entire outline of each tension bolt directly onto the wall.

Door stop must be on stair side of gate. Gate door must open away from stairs.

Loosen the lower and upper tension nuts and remove gate.

Place a wall cup over the center of each circular outline on the wall.

Mark drill holes with a pencil through the center of each wall cup.

1st: Drill a 7/32" pilot hole into each of the 4 center marks.

Note: If mounting into plaster or drywall, follow this step and use the wall anchors provided.

2nd: Insert wall anchors into pilot/holes.

1st: Remove backing from one side of each adhesive mounting pad.

2nd: Attach one pad to the back of each wall cup.

3rd: Remove backing.

Align the wall cups so the center hole is placed directly over the wall anchor. Stick wall cups to the wall.

Note: The bottom wall cups should rest on the floor.

Make sure all wall cups are facing up.

Screw wall cups into wall.

Repeat "installation" steps on page 5. The 4 tension bolts will rest within each wall cup.

IMPORTANT: NEVER open gate door over stairs.

Tighten all 4 tension nuts with the provided wrench.

Tighten top tension nuts so that the upper latch/handle goes below the release button completely.

FINISHED! ✔️

Testing the Installation:

1st: Close the gate. Make sure the upper and lower latches lock securely. ?

2nd: Push the gate and extension frames to check stability. ?

Operation:

To unlock gate:

1st: First, slide locking tab back to release. ➡️

2nd: Second, lift gate door open. ⬆️

Hold open feature:

To activate, open gate door at least 90° in either direction. ▶️

Troubleshooting:

If the gate does not close properly:

1. Gate is not properly aligned in the door frame.
   Solution: To adjust the gate's alignment, loosen all four tension bolts and reposition gate so that it matches the “correct" image. Re-tighten tension bolts.
2. Pressure of tension bolts needs to be adjusted.
   Solution: Loosen or tighten the upper tension bolts. Ensure the upper latch engages securely when the gate swings closed, and that it can be released properly when the sliding lock tab is pushed back.

Correct! ✔️

Incorrect! ❌

Maintenance:

• Regularly check tension bolts to make sure the gate is securely in place.
• Do not use the gate if any components are damaged or missing.
• Surface clean with a damp cloth or sponge using mild detergent and warm water.

Replacement Hardware Kit #27930-50

Summer Infant (USA), Inc.
1275 Park East Drive
Woonsocket, RI 02895 USA
401-671-6551
© 2018 Summer Infant (USA), Inc.

Text "Install Main" to 38344 for a step-by-step installation video.

For technical support or to order a replacement hardware kit, please contact us at 401-671-6551 or www.summerinfant.com/contact.

Please retain this information for future reference. Colors and styles may vary. MADE IN CHINA. 5/18