Znewtech - Innovate • Implement • Improve
User Manual for ZNEWTECH models including: 2BNIC-ZS-X3, 2BNICZSX3, zs x3, ZS-X3 Column Bathroom Scale, Column Bathroom Scale, Bathroom Scale, Scale
Znewtech ZS-X3 Column Bathroom Scale with Wireless Display 2BNIC-ZS-X3 2BNICZSX3 zs x3
File Info : application/pdf, 14 Pages, 1.22MB
DocumentDocumentDigital Column Scale with Wireless Display User Manual Z ZNEWTECH Getting to Know Your Znewtech Scale 1 Display Screen 2 Display Holder 3 Stand Poles 5 Scale Body 4 Stand Base 1 Part List A Scale Body (1 Unit) B Stand Poles (2 Units) C Stand Base (1 Unit) D Display Holder (1 Unit) E Display Screen (1 Unit) Assembly takes 5-10 minutes 2 Assembling Your Scale in 5 Steps Step 1 Install Batteries into Scale Body Install 4 AAA batteries into the battery compartment located underneath the Scale Body 3 Step 2 Install Batteries into Display Screen Install 4 AAA batteries into the battery compartment located at the back of the Display Screen 4 Step 3 Connect Stand Poles with Stand Base Assemble Upper Stand Pole Assemble Lower Stand Pole Stand Base 5 Step 4 Connect Display Holder with Stand Pole Assemble Display Holder Stand Pole Stand Base 6 Step 5 Attach Display Screen Display Holder Put Display Screen onto Display Holder Stand Pole Stand Base 7 Congratulations! You have completed all assembly steps. Place the scale body on a flat, hard surface, such as tile or hardwood floors, before weighing 8 Measuring Your Weight 1. Place the scale on the hard and flat surface 2. Make sure the display screen is within 7 feet distance of the scale body 3. Step on the scale body, remain still and the scale will count up to your weight. 4. The display will flash twice when the weight is locked. 5. Your weight will be displayed for about 10 seconds, and then the scale turns off automatically. Use the scale on a hard, level and even surface (no carpeting). Inconsistent and soft surfaces will cause inaccurate measurements. 9 Changing Weight Measurement Unit By default, your scale is set to calculate weights in pound (lb). To change the unit of measurement between pounds (lb) and kilograms (kg), simply short press the SET button (located underneath the scale body). SET Short Press: Change Unit Long Press: Rest Bluetooth Short press "SET" button 10 Re-pairing Bluetooth Connection By design, your Scale Body and Display Screen connect automatically via Bluetooth. If the Bluetooth connection is lost, a Bluetooth icon will appear on the screen and start flashing, and a flashing light will appear on the scale body. You can long press the SET button (located underneath the scale body) for 3 seconds to manually re-pair the Bluetooth connection. SET Short Press: Change Unit Long Press: Rest Bluetooth Long press "SET" button for 3 seconds If Bluetooth connection is already paired, long Press "SET" button will un-pair the Bluetooth connection 11 Troubleshooting No Display Check if batteries are installed according to their +/- polarity Low Battery Replace with new AAA batteries Lost Bluetooth Connection Long press "SET" Button underneath the scale body Overload Exceeded the maximum weight of 440 lb Flashing Light on Scale Body Connecting Bluetooth The scale automatically scans and re-connects Bluetooth This is by design Specifications Capacity: 440 lb (200 kg) Weight Increments: 0.2 lb (100 g) Switch-on Over: 3kg / 6lb Power Source: 8 AAA batteries Unit Modes: lb/kg Platform Size: 12" x 12" (31 cm x 31 cm) Display Stand Height: 36 " (92 cm) Support Our official website: www.znewtech.com Contact us at support@znewtech.com Warranty One-Year Limited Warranty Contact us at support@znewtech.com 12 FCC Warnning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.