BSIDE A10 Digital Multimeter
Brand: BSIDE
Introduction
This user manual is intended for learning about and correctly operating the digital multimeter (hereinafter referred to as the device). This manual contains information to ensure long-term and safe use of the device. The manufacturer reserves the right to make changes to the manual related to product improvements without prior notice. Please read this manual carefully before operating the device. By starting to use the device, the buyer confirms that they have read this manual and accept responsibility for any consequences arising from violations of its provisions, including safety rules, operation, storage, and disposal.
Package Contents
- Digital Multimeter – 1 pc.
- Probes – 2 pcs.
- Adapter – 1 pc.
- Case – 1 pc.
- Warranty Card – 1 pc.
- User Manual – 1 pc.
Purpose and General Characteristics
The device is designed for measuring electrical network parameters (current, resistance, etc.). It is intended for short-term use in domestic conditions, in areas with a moderate climate, with temperatures from 5°C to +40°C, relative humidity not exceeding 80%, and without direct exposure to atmospheric precipitation or excessive dust. This safety passport contains comprehensive information and requirements necessary for reliable, efficient, and safe operation of the device. Due to continuous product improvement, the manufacturer reserves the right to make minor design changes not reflected in this passport that do not affect the effective and safe operation of the device.
Appearance
The device consists of a plastic casing with an LCD display and a control panel equipped with a rotary switch for easy operation.
Device Components
- 1 – Power Button (⏻): Turns the multimeter on/off.
- 2 – Auto Mode Button: Enables/disables automatic measurement mode.
- 3 – Mode Selection Button: Cycles through measurement modes.
- 4 – Data Recording Function: Saves measurement data.
- 5 – LCD Display: Shows measurement readings and indicators.
- 6 – Non-Contact Voltage Sensor: Detects AC voltage without physical contact.
- 7 – Input Jacks: For connecting test probes.
Display Symbols and Indicators
| Symbol | Meaning |
|---|---|
| AC | AC Voltage |
| DC | DC Voltage |
| ))) | Continuity Test (Buzzer sounds if resistance < 50 Ω) |
| ? | Low Battery: Needs replacement or charging. |
| ? | Auto Power Off function enabled. |
| ⨏ | Capacitance measurement mode. |
| NCV | Non-Contact Voltage sensor active. |
| °C / °F | Temperature measurement units. |
| V | Volts |
| Ω, kΩ, MΩ | Ohms, Kilohms, Megohms |
| µF, nF, mF | Capacitance units. |
| Hz, kHz | Hertz, Kilohertz |
| Hold | Data Hold function active. |
| Live | Live Wire Detection active. |
| % | Duty Cycle measurement. |
Technical Specifications
| Parameter | Specification |
|---|---|
| Model | BSIDE A10 |
| Display | Color LCD |
| Max. Count | 9999 |
| Measurement Speed | Updates every 0.4 seconds |
| Auto Measurement Modes | AC/DC Voltage, Resistance |
| Overload Indication | "1" displayed |
| Max. Voltage (AC/DC) | 600V |
| Polarity | Automatic indication |
| Low Battery Indication | Battery symbol ? on display |
| Auto Power Off | After 5 minutes of inactivity |
| Max. Operating Altitude | 2000 meters |
| Operating Conditions | 0°C - +40°C, humidity <80% |
| Storage Conditions | -10°C - +60°C, humidity <70% |
| Power Source | Li-Ion battery |
| Accuracy Guarantee | 1 year (at 18°C - 28°C, <80% humidity) |
DC Voltage Measurement
| Range | Resolution | Accuracy |
|---|---|---|
| 0-600V (DC mode) | 0.001V | ±(0.8%+3 digits) |
| 0-600V (Auto mode) | 0.001V | ±(0.8%+3 digits) |
| Input Impedance: 10 MΩ | ||
| Max Input Voltage: 600V DC/AC | ||
AC Voltage Measurement
| Range | Resolution | Accuracy |
|---|---|---|
| 0-600V (AC mode) | 0.001V | ±(1.2%+5 digits) |
| 0-600V (Auto mode) | 0.001V | ±(1.2%+5 digits) |
| Input Impedance: 10 MΩ | ||
| Max Input Voltage: 600V | ||
| Frequency Range: 10-10 MHz (3V-600V) | ||
Capacitance Measurement
| Range | Resolution | Accuracy |
|---|---|---|
| 1 nF - 1 mF | 0.01 nF | ±(1.2%+3 digits) |
| 1 mF - 60 mF | ±(2.0%+10 digits) |
Resistance Measurement
| Range | Resolution | Accuracy |
|---|---|---|
| 0.1 Ω - 10 MΩ | 0.1 Ω | ±(3.5%+8 digits) |
| 10 MΩ - 60 MΩ | ±(4.5%+10 digits) |
Frequency Measurement
| Range | Resolution | Accuracy |
|---|---|---|
| 10-10 MHz | 0.1 Hz | ±(2.0%+10 digits) |
Duty Cycle Measurement
| Range | Resolution | Accuracy |
|---|---|---|
| 0.1-99.9% | 0.1 % | ±(1.5%+5 digits) |
Other Functions
| Function | Principle of Operation |
|---|---|
| Diode Test | Measures voltage drop within 3V. |
| Continuity Test | Buzzer sounds if resistance < 50 Ω. |
| Non-Contact Voltage Detection (NCV) | Display shows NCV icon ⚡; buzzer sounds when signal is detected. |
| Live Wire Detection | Display shows Live icon ⚡; buzzer sounds when signal is detected. |
| Temperature Measurement | Range: 0-50 °C, Accuracy: ±2 °C. |
| Auto Power Off | After 5 minutes of inactivity. |
Safety Instructions
⚠️ Warning: Carefully read and strictly follow the safety rules below.
- Use the device only for its intended purpose as described in this manual.
- Perform necessary maintenance promptly. Any modification or alteration of the device is prohibited and may lead to malfunction or injury.
- Device Inspection: Before each use, visually inspect the device for integrity and absence of damage, and ensure all parts are securely fastened.
- Attention: Do not operate the device if it is faulty! Remove the battery before performing any adjustments, maintenance, or storage.
- General Safety Measures:
- Store the device out of reach of children and do not let them play with it.
- Do not dispose of batteries in fire.
- Never short-circuit batteries. Observe correct polarity (+/-) when installing batteries. Do not attempt to recharge non-rechargeable batteries.
- Do not expose batteries to heat (direct sunlight, heaters, fire, etc.).
- Do not use the device at temperatures above 40°C.
- Read this manual carefully before use.
- When using electrical appliances, especially in the presence of children, observe basic safety rules to avoid the risk of fire or electric shock.
- The device can be used outdoors.
- The device must be used only for its intended purpose.
- Do not use the device near heat sources (heaters, fire).
- Always remove the battery before cleaning or long-term storage.
- Prevent liquid from entering the device.
- Storage Note: Store the device in closed or ventilated rooms with moderate temperature and humidity, not exceeding +40°C or below -50°C, with relative humidity not exceeding 80% at +25°C, in accordance with GOST 15150-89 storage conditions.
Operation
Transport: The device can be transported by any type of closed transport in the manufacturer's packaging or without it, protected from mechanical damage, atmospheric precipitation, and chemically active substances, adhering to fragile goods transport precautions (GOST 15150-89, section 8).
Button Functions:
- Power Button (⏻):
- Long press: Turn the multimeter on.
- Long press (when on): Toggle auto power-off mode.
- Short press: Turn the multimeter off.
- AUTO Button:
- Short press: Cycle through measurement modes (automatic, AC/DC voltage, NCV, live wire detection, duty cycle).
- Long press: Switch temperature units (°C/°F).
- FUNC Button:
- Short press: Cycle through modes (Capacitance, Resistance, Continuity Test, Diode Test).
- Long press: Activate automatic measurement mode.
- HOLD Button:
- Short press: Record current measurement data.
Battery Installation/Replacement
- A low battery symbol ? will appear on the screen when the device needs charging.
- Turn off the device and disconnect the probes.
- Remove the protective case.
- Use a Type-C adapter to charge the device.
- The charging indicator will be red while charging and turn green when charging is complete.
Measurement Guides
DC Voltage Measurement (Automatic Mode)
Connect the red probe to the V/Ω/Hz/etc. jack and the black probe to the COM jack. Connect the probes to the DC voltage source. The display will show the measured DC voltage.
AC Voltage Measurement (Automatic Mode)
Connect the red probe to the V/Ω/Hz/etc. jack and the black probe to the COM jack. Connect the probes to the AC voltage source. The display will show the measured AC voltage.
Resistance Measurement
Connect the red probe to the V/Ω/Hz/etc. jack and the black probe to the COM jack. Connect the probes across the component or circuit to measure resistance. The display will show the resistance value.
Continuity Test
Connect the red probe to the V/Ω/Hz/etc. jack and the black probe to the COM jack. Connect the probes to the circuit. If the resistance is below approximately 50 Ω, a buzzer will sound ?, and the display will show "0.0".
Capacitance Measurement
Connect the red probe to the V/Ω/Hz/etc. jack and the black probe to the COM jack. Connect the probes across the capacitor. Ensure the capacitor is discharged before measurement. The display will show the capacitance value (e.g., 50.00 µF).
Diode Test
Connect the red probe to the V/Ω/Hz/etc. jack and the black probe to the COM jack. Connect the probes across the diode (observing polarity). The display will show the forward voltage drop (e.g., 2.223V). If the diode is reverse-biased or open, the display may show "OL".
Non-Contact Voltage Detection (NCV)
Hold the multimeter near an AC voltage source. The NCV sensor (6) will detect the voltage, and the display will show "VALE" along with the NCV icon ⚡. A buzzer may sound.
Live Wire Detection
Place the probe tip near a suspected live wire. The multimeter will detect the live voltage, indicated by the "Live" display and the Live icon ⚡, accompanied by a buzzer sound.
Service Life and Disposal
With proper adherence to the requirements in this manual and the warranty card, the service life of the product is 3 years. After the service life, the device may continue to be used if its condition meets safety requirements and it retains its functional properties. Do not dispose of the device or its components as household waste. Dispose of the device according to your regional waste disposal regulations. For information on collection points for electrical appliances, contact your local administration, waste recycling service, or the retailer where the product was purchased.
Warranty Obligations
The warranty period for the device is 12 months from the date of retail sale (or 1 month for commercial/professional use). Warranty repair is provided under the following conditions: 1. Presence of a sales receipt. 2. Submission of the faulty device in a complete and clean condition. Warranty service is not provided for: 1. Devices with illegible or altered serial numbers. 2. Consequences of independent repair, disassembly, cleaning, or lubrication not specified in the operating instructions, evidenced by, for example, damage to the screw heads on housing components. 3. Malfunctions reported late. 4. Devices operated in violation of the instructions or not for their intended purpose. 5. Damage caused by external mechanical impact, aggressive substances, high temperatures, or other external factors like rain, snow, or high humidity. 6. Malfunctions caused by foreign objects, negligent care, or poor maintenance leading to device failure. 7. Malfunctions caused by the use of non-original spare parts or accessories. 8. Defects arising from operation with uncorrected prior faults. 9. Defects arising from technical maintenance or modifications by unauthorized service centers. 10. Natural wear and tear from intensive use. 11. Maintenance tasks such as adjustment, cleaning, lubrication, replacement of consumables, and periodic servicing as described in the manual. 12. Incomplete product комплектация discovered at the time of sale is not covered by the warranty. Warranty does not cover consumables and components that are subject to wear and tear, such as accessories (replaceable parts) included in the package or installed by the user, e.g., probe kits, batteries, and other replaceable parts.
Manufacturer and Importer Information
Exporter/Manufacturer: SHENZHEN AIMOMETER CO., LTD.
Address: Zhenye City Comprehensive Building, Shenfeng Road No. 2, Hongmian Community, Henggang Street, Longgang District, Shenzhen, China.
Importer/Authorized Representative: OOO "ZITREK RUS"
Importer Address: 107078, Moscow, Novoryazanskaya St., bld. 18.
Phone: +7(905)518-81-22
Email: info@z3k.ru
Made in China
Production Date: Indicated on individual packaging.
Product Compliance: Conforms to TR CU 020/2011 "Electromagnetic compatibility of technical means". EAC mark.
Service Centers: A list of service centers can be found at: https://z3k.ru/service/
Сервис
