Aquaguard Blaze: Your Trusted Water Purifier

Why Aquaguard?

• Trusted by over 15 million mothers.
• Owned by over 1.62 lakh doctors.
• Service available within 5 km range.
• 21 different technologies for diverse water conditions across India.
• Tested and certified by 130+ leading national and international laboratories.

The Power of Aquaguard Blaze

The Aquaguard Blaze Hot & Ambient is equipped with patented Active Copper™ technology, which infuses copper ions into the water, known for its antimicrobial properties. It also features Mineral Guard™ technology to retain essential natural minerals. The Zero Pressure Pump allows water to be drawn even at zero pressure and can suck water from up to 1 meter below the purifier. The RO membrane effectively removes viruses, bacteria, and modern contaminants like lead and mercury, ensuring your family stays safe and healthy.

Aquaguard Blaze Hot & Ambient Features

With an aesthetic design and metallic finish, the Aquaguard Blaze Hot & Ambient complements any home or office environment.

• Active Copper™ Cartridge: Provides antimicrobial, antioxidant, and anti-inflammatory benefits, supporting healthy metabolism. Activated carbon polishes the water for better taste.
• Mineral Guard™ Technology: Retains natural essential minerals that other purifiers might remove.
• Dual Protection: Advanced RO+UV purification for comprehensive safety (for RO+UV+MTDS models).
• Superior RO Purification: Removes contaminants like lead and mercury.
• MTDS: Ensures the purifier works with various water sources up to 2,000 ppm TDS (for RO+UV+MTDS models).

Installing Your Aquaguard Blaze

Installation must be performed by a trained Eureka Forbes Service Technician.

1. Input water must be tested for Total Dissolved Solids (TDS).
2. Install the purifier in a dry, ventilated place, away from direct sunlight, heating devices, or freezing temperatures. Ensure adequate height to avoid hot water splashes.
3. Input water temperature should be between 10°C - 40°C. Avoid connecting to a hot water tap.
4. Ensure tap water pressure does not exceed 3.0 kg/cm². If it does, a Pressure Reducing Valve (PRV) is mandatory.
5. Flush filters and membrane thoroughly for 3-5 minutes.
6. Ensure the reject water pipe is positioned lower than the purifier.
7. The TDS regulator should be adjusted by a trained technician for optimal water quality.
8. Do not switch on the heater until the storage tank is completely filled during the first-time usage.

Input Water Quality Usage Limitations:

• For iron content above 0.3 mg/litre, an iron remover is recommended.
• For turbidity above 5 NTU, a special pre-filter is required.
• For TDS above 1,000 ppm or hardness above 300 ppm, a Membrane Life Enhancer is recommended.
• Do not install if TDS exceeds technical specifications.

Purification Process of Aquaguard Blaze RO+UV+MTDS

The multi-stage purification process includes:

• i-Filter™: Removes suspended particles like dust, dirt, and sand.
• Chemi-Block: Adsorbs color, odor, excess chlorine, and organic impurities.
• Mineral Guard™: Retains essential minerals like Calcium and Magnesium.
• Reverse Osmosis (RO) Membrane: Reduces TDS, hardness, pesticides, and heavy metals; eliminates microorganisms.
• UV e-boiling: Disinfects water by eliminating disease-causing bacteria and viruses.
• Active Copper™ Cartridge: Provides antimicrobial benefits and enhances taste.
• MTDS Regulator: Adjusts TDS for healthy water.

LED Indication Chart for Aquaguard Blaze RO+UV+MTDS

Technical Specifications* Blaze RO+UV+MTDS

*Technical Specifications are subject to change without prior notice.

Note: Performance data is applicable under standard laboratory conditions. Actual performance may vary. If input water pressure is higher than specified, a pressure reducing valve is mandatory. Accessories available at extra cost. If input water TDS > 1,000 ppm or hardness > 300 ppm, a Membrane life enhancer is recommended.

How to Dispense Water from Aquaguard Blaze

To Dispense Ambient Water:

• Press the ambient tap towards the product. Release to stop.
• Lift the tap lever for continuous flow. Pull down to stop.

To Dispense Hot Water:

• Switch ON the heater switch. Heating takes 6-8 minutes to reach approx. 85°C.
• Dispensed through the red hot water tap.
• Push the child lock button and then the lever for dispensing. Release to stop.
• Lift the tap lever and push the child lock for continuous hot water flow. Pull down to stop.

Note: Hot water temperature may vary. Heating capacity is 5 litres per hour.

Tips for Safety and Maintenance

• Read and understand the purifier functions before use.
• Installation and service by authorized Eureka Forbes personnel only.
• Install in a well-ventilated, dry place, away from direct sunlight or heat sources.
• Maintain a 5cm gap from the wall for cooling.
• Connect to a grounded 230V AC power socket; use voltage stabilizers if needed.
• Turn ON the heater switch for hot water; allow time for heating.
• Do not switch on the heater until the tank is full for the first use.
• Discard ~10 litres of water after installation or filter replacement.
• Do not handle plugs with wet hands.
• Replace filters when the end-of-life indicator is displayed.
• Use only genuine Eureka Forbes filter cartridges and spares.
• Always switch off and unplug before maintenance or cleaning.
• Contact an authorized service center for any damage or malfunction. Do not attempt self-repair.

Consumable Components & Service Life

Note: Refer to Standard Test Conditions for filter life.

Precautions

• Hot water can cause burns; avoid touching with bare hands.
• Do not overfill containers with hot water.
• Keep children away from operating the hot water dispenser.
• Keep the heater switched OFF when not in use to prevent ambient water temperature increase.

Safety Features

• Separate switch for heater operation.
• Child lock for the hot water tap to prevent accidental use.
• Thermostat to prevent overheating of hot water.

Important Note on Zero Pressure Pump (ZPP) and Dry Run Sensor (DRS)

The Aquaguard is equipped with a ZPP and DRS, enabling it to function under various conditions:

• Normal Input Water Pressure (up to 3 bar max.)
• Low Water Pressure from Loft Tank
• Zero Water Pressure
• Suction Mode (up to 1m below product level)

Product Functioning with Normal/Low & Zero Pressure:

• Ensure water flow into the product is > 1.5 LPM.
• DRS detects water unavailability and stops the unit to prevent dry running.
• DRS restarts the product when water supply resumes. The unit intelligently checks for water availability.
• If the product is in standby mode when water supply resumes, restart by switching the power OFF and ON.

Product Functioning with Suction Capability:

• DRS stops the product when the water container is empty. Restart by switching power OFF and ON.
• Prolonged use in loft tank/suction mode may affect pump performance and filter life. A booster pump is recommended for low pressure if performance is not met.
• Do not recirculate rejected water back into the product.
• The booster pump can suction water from 1m below the product level (e.g., from a bucket).
• Not suitable for suction from underground storage tanks, sumps, or open wells beyond 3 feet below the product level.

Warranty Terms & Conditions

1. Warranty is for 12 months against manufacturing defects from the date of original purchase.
2. Notify the company in writing of any defects and allow inspection. Deposit goods at your expense if required.
3. The company's inspection and test report is final.
4. Aquaguard may require initial setting post-installation. Contact the service center for service requirements.
5. The company may retain defective parts.
6. The company's liability is limited to the first sale and does not cover defects from misuse, neglect, unauthorized repairs, or use on incorrect electrical supply.
7. Warranty is valid only if installed by the company or its authorized agency.
8. Consumable items are subject to normal wear and tear and are not covered.
9. RO Membrane warranty is 1 year or 6,000 liters (whichever is earlier), provided input water meets standard test conditions. Clogged membranes will be serviced free of charge after inspection.
10. The company is not liable for death, injury, or property damage due to equipment failure, misuse, or causes beyond its control.
11. The company's liability shall not exceed the price paid by the customer.

General Definitions:

• 'Goods': Products described in the Order Form.
• 'Customer': Original purchaser.
• 'Company': EUREKA FORBES LIMITED.
• 'Aquaguard®': Includes Aquaguard®, Aquaguard® Select, and Sure from Aquaguard®.
• 'General Terms & Conditions': Agreed terms on the Order Form.
• 'Invoice': Issued by the company to the customer.
• 'User Manual': Instructions provided with the product.

Eureka Forbes Limited reserves the right to change terms and conditions without prior notice. Disputes are subject to Mumbai Jurisdiction.

Post-Warranty Services

• Yearly Service Contracts may be offered at prevailing rates.
• Customers can opt for pay-per-service calls, paying for labor and spares.
• Customers will pay for replacement or repair of defective components during servicing.
• Eureka Forbes Limited ensures spare availability for up to 7 years from the invoice date.

The Aquaguard® Advantage

Both the old and new Aquaguard logos represent original Aquaguard® products from Eureka Forbes Limited.

Environment Protection

Eureka Forbes encourages recycling of packaging material. Dispose of old products responsibly at local e-waste centers. Contact the nearest authorized service center for guidance.

Health Protect™

Specially designed and authenticated purification cartridges ensure 'pure & healthy water or no water'. An indication light alerts you to the usage of non-genuine cartridges or when genuine cartridges reach the end of their usable life (6,000 liters), prompting you to contact Eureka Forbes for replacement. This feature even shuts down the purification process for complete protection.