ECOVACS DEEBOT T30 PRO OMNI Instruction Manual

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical Appliance, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE

SAVE THESE INSTRUCTIONS

1. The Appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the Appliance by a person responsible for their safety.
2. Clear the area to be cleaned. Remove power cords and small objects from the floor that could entangle the Appliance. Tuck rug fringe under the rug base, and lift items such as curtains and tablecloths off the floor.
3. If there is a drop off in the cleaning area due to a step or stairs, you should operate the Appliance to ensure that it can detect the step without falling over the edge. It may become necessary to place a physical barrier at the edge to keep the unit from falling. Make sure the physical barrier is not a trip hazard.
4. Only use as described in this manual. Only use attachments recommended or sold by the manufacturer.
5. For INDOOR household use ONLY. Do not use the Appliance in outdoor, commercial or industrial environments.
6. Do not use without dust bin and/or filters in place.
7. Do not operate the Appliance in an area where there are lit candles or fragile objects.
8. Keep hair, loose clothing, fingers, and all parts of body away from any openings and moving parts.
9. Do not operate the Appliance in a room where an infant or child is sleeping.
10. Do not use Appliance on wet surfaces or surfaces with standing water.
11. Do not allow the Appliance to pick up large objects like stones, large pieces of paper or any item that may clog the Appliance.
12. Do not use Appliance to pick up flammable or combustible materials such as gasoline, printer or copier toner, or use in areas where they may be present.
13. Do not use Appliance to pick up anything that is burning or smoking, such as cigarettes, matches, hot ashes, or anything that could cause a fire.
14. Do not put objects into the suction intake. Do not use if the suction intake is blocked. Keep the intake clear of dust, lint, hair, or anything that may reduce air flow.
15. If the power cord is damaged, it must be replaced by the manufacturer or its service agent in order to avoid a hazard.
16. Turn OFF the power switch before cleaning or maintaining the Appliance.
17. The lithium battery type suitable for CH2311A is Max. 8 cells, max. nominal voltage DC 14.4V, rated capacity 4,800mAh. The battery must be removed and discarded according to local laws and regulations before disposal of the Appliance.
18. Please dispose of used batteries according to local laws and regulations.
19. Do not incinerate the Appliance even if it is severely damaged. The batteries can explode in a fire.
20. The Appliance must be used in accordance with the directions in this Instruction Manual. Ecovacs Home Service Robotics cannot be held liable or responsible for any damages or injuries caused by improper use.
21. The robot contains batteries that are only replaceable by skilled persons. To replace the robot's battery, please contact Customer Service.
22. Please make sure your power supply source voltage matches the power voltage marked on the OMNI Station.
23. Use only the original rechargeable battery and OMNI Station provided with the Appliance from the manufacturer. Non-rechargeable batteries are prohibited.
24. Take care not to damage the power cord. Do not pull on or carry the Appliance or OMNI Station by the power cord, use the power cord as a handle, close a door on the power cord, or pull power cord around sharp edges or corners. Do not run Appliance over the power cord. Keep power cord away from hot surfaces.
25. Do not use the OMNI Station if it is damaged. The power supply is not to be repaired and not to be used any longer if it is damaged or defective.
26. Do not use with a damaged power cord or receptacle. Do not use the Appliance or OMNI Station if it is not working properly, has been dropped, damaged, left outdoors, or come in contact with water. It must be repaired by the manufacturer or its service agent in order to avoid a hazard.
27. The plug must be removed from the receptacle before cleaning or maintaining the OMNI Station.
28. Remove the Appliance from the OMNI Station, and turn OFF the power switch to the Appliance before removing the battery for disposal of the Appliance.
29. When not using the OMNI Station for a long period of time, please unplug it.
30. If the robot will not be used for a long time, power OFF the robot for storage and unplug the OMNI Station.
31. WARNING: Add clean water into the clean tank only.
32. WARNING: For the purposes of recharging the battery, only use the detachable supply unit CH2311A provided with the Appliance.

To satisfy RF exposure requirements, a separation distance of 20 cm or more should be maintained between this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter.

Device Update

Typically, some devices are updated bi-monthly, but not always so specific. Some devices, especially those that went on sale more than three years ago, will only be updated if a critical vulnerability is found and fixed.

Symbols and Notes

The remote surveillance is for the absolute private use of non-public, private owned places for the pure self-protection and single control intended only. Please be aware of the local data protection based legal obligations in case of use. No surveillance of public places, especially with clandestine intent and/or on the part of the employer without justified reasons. Such not justified use is in the risk and responsibility of the user only.

European Union Compliance Statement

Information on Disposal for Users of Waste Electrical & Electronic Equipment

This symbol on the product or on its packaging indicates that used electrical and electronic products should not be mixed with unsorted municipal waste. For proper treatment, it is your responsibility to dispose of your waste equipment by arranging to return it to designated collection points. Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling.

To return your used device, please use the return and collection systems or contact the retailer where the product was purchased, which is free of charge. Please contact your local authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, in accordance with your national legislation.

Information on Disposal for Users of used batteries

This symbol means that batteries and accumulators, at their end-of-life, should not be mixed with unsorted municipal waste. Your participation is an important part of the effort to minimize the impact of batteries and accumulators on the environment and on human health. For proper recycling you can return this product or the batteries or accumulators it contains to your supplier or to a designated collection point, which is free of charge.

Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Penalties may be applicable for incorrect disposal of this waste, in accordance with your national legislation. There are separate collection systems for used batteries and accumulators. Please, dispose of batteries and accumulators correctly at your local community waste collection/recycling center.

Regulatory Information

Restriction of the use of certain hazardous substances (RoHS) Directive

Ecovacs Home Service Robotics Co., Ltd. hereby declares the whole product including parts (cables, cords, and so on) meets the requirements of RoHS Directive 2011/65/EU and amendment Commission Delegated Directive (EU) 2015/863 on the restriction of the use of certain hazardous substances in electrical and electronic equipment ("RoHS recast" or "RoHS 2.0").

Radio Equipment Directive

Ecovacs Home Service Robotics Co., Ltd. hereby declares that the product listed in this section comply with the essential requirements and other relevant provisions of the Radio Equipment Directive 2014/53/EU.

Europe Authorised Representative:

ECOVACS Europe GmbH, Holzstrasse 2 | D-40221 Düsseldorf | Germany

Ecovacs Home Service Robotics Co., Ltd. hereby declares that the product comply with the essential requirements and other relevant provisions of the RoHS Directive 2011/65/EU and amendment Commission Delegated Directive (EU) 2015/863, the Radio Equipment Directive 2014/53/EU. The declaration of conformity can be viewed at the following address: https://www.ecovacs.com/global/compliance.

PRODUCT DIAGRAM

Robot

Top View Components:

• Top Cover
• TrueMapping: Navigation system.
• TrueDetect 3D Sensor: Advanced sensor for object detection.
• Buttons: Control interface.
• Edge Sensor: Detects edges to prevent falls.
• Anti-collision Sensors and Bumper: Detects and avoids obstacles.

Bottom View Components:

• Anti-drop Sensors: Detects drops and stairs.
• Carpet Detection Sensor: Identifies carpets to adjust suction.
• Universal Wheel: For maneuverability.
• Side Brush: Sweeps debris towards the main brush.
• Main Brush: Main cleaning brush.
• Brush Release Button: For removing the main brush.
• Driving Wheels: Propel the robot.
• Mounting Slots for Mopping Pad Assembly: For attaching mopping accessories.

Button Functions:

• Short press: Exit/Return to the Station
• Short press: Start/Pause/Continue
• Short press: Start/End Spot Cleaning
• Long press: Self-clean
• Long press: Power on/Power off
• Long press: Child Lock

RESET Button

Restore to default settings: Press and hold RESET button for 5 seconds. After you hear the voice prompt, the startup music will be played and the robot will be restored to default settings.

Other Robot Components:

• Microphone: For voice commands.
• Charging Contacts: Connects to the charging station.
• Water Filling Port: For adding cleaning fluid.
• Data Transfer Port: For professional maintenance personnel use only.
• Wi-Fi Status Indicator: Shows Wi-Fi connectivity status.

Dust Bin Components:

• Filter
• Sponge Filter
• Dust Disposal Port
• Dust Bin Handle
• Filter Net
• Release Button

Mopping Pad Assembly Components:

• Mopping Pad Plates
• Washable Mopping Pads

OMNI Station

Front View Components:

• Clean Water Tank
• Light Strip: Indicates status (Glowing White: Standby/Running/Self-clean; Flashing Red: Malfunction; Goes out: Power Outage/Deep Sleep Mode).
• Dust Collection Cabin
• Charging Contacts
• Dirty Water Tank
• Cleaning Sink

Back View Components:

• Air Vent
• Cable Trunking
• Power Socket

Dust Bag Components:

• Dust Bag Handle

Note:

• If the Light Strip is flashing red, please check the reason in ECOVACS HOME App.
• If DEEBOT fails to charge, please wipe Charging Contacts with a clean and dry cloth.

SENSORS

NOTES BEFORE CLEANING

Preparation:

• Tidy up the area by putting furniture, such as chairs, in their proper place.
• During the first use, make sure each room door is open to help DEEBOT fully explore your house.
• It may be necessary to place a physical barrier at the edge of a drop to stop the unit from falling over the edge.
• Put away objects including cables, cloths, and slippers, etc., on the floor to improve the cleaning efficiency.
• Before using the product on a rug with tasseled edges, please fold the rug edges under.
• Please do not stand in narrow spaces, such as hallways, and make sure not to block the TrueMapping Distance Sensor.

QUICK START

1 Installation

The sound of "Click" indicates proper installation.

Step 1: Connect components by aligning them and pressing until a "Click" is heard.

Step 2: Assemble and Place the Station.

Keep the area around the Station clear of objects, especially those with reflective surfaces.

Station Placement Requirements:

• Maintain at least 0.05m (0.16') clearance on the sides.
• Maintain at least 0.8m (2.62') clearance in front.
• If there are reflective objects (mirrors, skirting lines) nearby, cover the bottom 14cm of the Station.
• Do not place the Station under direct sunlight.
• It is recommended to place the Station on a hard floor for optimal performance.
• Place the Station in a location with a strong Wi-Fi signal.

Note:

• It is recommended to use ECOVACS DEEBOT Cleaning Solution (sold separately). Using other cleaning solutions may cause DEEBOT slipping, water tank blockage, or other problems.
• Water drops in the Water Tank are from the function test and are safe to use.

Use Tanks

Instructions for filling water tanks (details not provided in text, only visual reference).

CONNECT DEEBOT WITH APP

DOWNLOAD THE ECOVACS HOME APP

To enjoy all available features, it is recommended to control your DEEBOT via the ECOVACS HOME App.

1. Scan the QR Code under the Top Cover to download the App.
2. Search for "ECOVACS HOME" to download the App from your app store.

CONNECT DEEBOT WITH APP

1. Via Bluetooth:

Turn on the DEEBOT and mobile phone Bluetooth. Allow the App to obtain mobile phone Bluetooth permission. Tap to scan the QR Code on DEEBOT or tap [Add icon] in the App to find nearby DEEBOT.

2. Via Wi-Fi:

You can also choose to connect DEEBOT with the App through other methods according to the prompts on the App's page.

Note: Please select the appropriate connecting method.

Wi-Fi Network Requirements:

• You are using a 2.4GHz or 2.4/5 GHz mixed network.
• Your router supports 802.11b/g/n and IPv4 protocol.
• Do not use a VPN (Virtual Private Network) or Proxy Server.
• Do not use a hidden network.
• WPA and WPA2 using TKIP, PSK, AES/CCMP encryption.
• WEP EAP (Enterprise Authentication Protocol) is not supported.
• Use Wi-Fi channels 1-11 in North America and channels 1-13 outside North America (refer to local regulatory agency).
• If you are using a network extender/repeater, the network name (SSID) and password must be the same as your primary network.
• Please enable WPA2 on your router.

Wi-Fi Indicator Light:

Please be aware that the realization of intelligent functions such as remote startup, voice interaction, 2D/3D map display and control settings, and personalized cleaning (depending on different products) requires users to download and use the ECOVACS HOME App, which is constantly updated. Users must agree to the Privacy Policy and User Agreement to process basic information and enable product operation. If you do not agree, some intelligent functions may not be realized, but basic manual operation will still be available.

OPERATION

Power ON and Charge DEEBOT

1. Power On: Press and hold the [Power Button] for 3 seconds. Wait for the startup music to play, indicating that the DEEBOT has powered on.

2. Return to Station: Short press the [Station Button] to recall DEEBOT to enter the Station to charge. (Charging time is approximately 6.5 hours).

Note: After DEEBOT enters the Station, wait for about 5 seconds and you will hear the voice prompt "Pairing Successful".

Note: When DEEBOT is not working, it is recommended to keep it powered ON and charging.

OPERATE DEEBOT

DEEBOT will create a map during the first-time cleaning. When creating a map for the first time, please follow DEEBOT to help eliminate some minor issues. For example, DEEBOT may get stuck under furniture. Please refer to the following solutions:

1. Raise low-sitting furniture if possible.
2. Cover the bottom of the furniture.
3. Set up Virtual Boundary via the App.

Short press the [Start Button] to start. For the first-time cleaning, please ensure that DEEBOT is fully charged.

TECHNICAL SPECIFICATIONS

Output power of the wireless module is less than 100mW.

Note: Technical and design specifications may be changed for continuous product improvement.

Explore more accessories at https://www.ecovacs.com/global.

Scan the QR code for more information.