User Manual for SYNCHRO models including: TRIMIX-S2, TRIMIXS2, 2AXVZ-TRIMIX-S2, 2AXVZTRIMIXS2, 152Y, Remote Controller with Control Box
Zhejiang Tri mix Technology Co., Ltd TRIMIX-S2 Control Box 2AXVZ-TRIMIX-S2 2AXVZTRIMIXS2 trimix s2
Remote controller: 152Y 152Y--USER'S MANUAL Control box (works with remote controller) :152Y I.ELECTRONICS OVERVIEW Power supply Controll box Remote controller: 152Y motor Control box (works with remote controller) :152Y 1 II. PAIRING THE WIRELESS REMOTE STEP 1 Push in on bottom of remote to release battery cartridge and install three AAA batteries into the remote battery compartment.Push in firmly to close. STEP 2 Plug the base into a power source and press the Pairing Button/Program Button on the control box approximately in 1s,ensure the Pairing Lamp - White (Third) flashing. STEP 3 Press "SW" until the backlight LED flashing ,release it and then press "HEAD UP" ,never release until the backlight LED is lighting all long,the remote is pairing and release it. Second,Press "BACK UP", never release until the backlight LED is lighting all long and then release. Pairing Button/Program Button Pairing Lamp - White (Third) First, Press "SW"button until the backlight LED flashing and then release. When the Pairing Button/Program Button on the control box and the backlight LED on the remote stop flashing, and the buzzer on the control box has a "DI" sound,pairing is completed. If the function on the remote can not be operated,repeat the pairing again. 4 III. FUNCTIONAL OPERATING FOR WIRELESS REMOTE MARK STEP1 STEP2 FUNCTIONAL DESCRIPTIONS The backlight LEDs all OFF before operating. TV PressTV,ZG,Muntil the backlight LED is lighting and the memory position is completed. ZG MEMORY POSITON When the backlight LED is lighting and press again, clear Press "SW" in 3s until the backlight LED M BACK UP PAIRING the corresponding memory position. TV & ZG have the memory position ,M no memory position. Pairing the remote and control box. flashing and then press the "BUTTON" in STEP 2 Press LEG UP 3 seconds Press SW 3 seconds CONTROL SWITCHING Control Switching is the backlight LED of "SW" is OFF. Control Switching is the backlight LED of "SW" is ON. Press BOTTOM LED 3 seconds Control Switching is the backlight LED of "SW" is FLASHING. IV. FUNCTIONAL OPERATING FOR WIRELESS REMOTE Power supply: Input: 100-240V ~, 50/60Hz Output:29.0V 1.8A Motor: By pairing the remote control with the control box, the motor can be controlled up and down Product interface description The interfaces in the red box below are only used for engineering testing and are not open to consumers. FCC/ISEDC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment . This transmitter must not be colocated or operating in conjunction with any other antenna or transmitterAcrobat Distiller 18.0 (Windows)