Welcome
Thank you for choosing this JBL® product. Your new JBL® powered subwoofer incorporates a high-performance transducer and built-in amplifier that deliver powerful, dynamic, and accurate low-frequency performance for your film soundtracks and music. With adjustable crossover, phase controls, and automatic turn on/off, it is simple to connect and set up.
We are confident that this JBL subwoofer will provide every note of enjoyment you expect. When considering additional audio equipment for your home, car, or office, choose JBL products again. This quick-start guide contains all the information needed to set up, connect, and adjust your new subwoofer. For more in-depth information, visit www.jbl.com.
What's Included
- 1 x JBL SUB 100P
- 1 x Power Cord
- 1 x Owner's Manual
- 1 x Safety Sheet
Rear Panel Controls and Connections
Diagram of the JBL SUB 100P rear panel showing controls: Power Mode (Auto/On), Phase (Normal/Reverse), Crossover (50Hz-150Hz), Volume, Subwoofer Input (LFE), Power Switch (On/Off), Power Input. An LED indicator displays status (Blue: On, Red: Standby).
- 1) Power Mode:
- When set to 'Auto', the subwoofer enters Standby mode. It automatically turns on when an audio signal is detected and returns to Standby after approximately 10 minutes of no signal. Setting this switch to 'On' keeps the subwoofer powered until the Power Switch is turned 'Off.'
- 2) On/Standby LED:
- Indicates the subwoofer's status when the Power Switch is 'On'. Blue LED means the subwoofer is On. Red LED means the subwoofer is in Standby mode.
- 3) Phase Switch:
- Determines if the subwoofer transducer's piston-like action is in phase with the main speakers. Playing out of phase can cancel sound waves, reducing bass performance and sonic impact. This depends on speaker placement relative to the listening position and each other.
- 4) Crossover Control:
- Sets the highest frequency at which the subwoofer reproduces sound. A higher setting increases the subwoofer's operating frequency and bass overlap with speakers, aiding a smooth bass transition. Adjust for a smooth bass response, lowering if bass is too strong, or raising if too weak.
- 5) Volume:
- Adjusts the subwoofer's volume. Turn clockwise to increase, counter-clockwise to decrease. Balance with other speakers; this setting should not need frequent changes.
- 6) Subwoofer (LFE Input):
- Connect to the dedicated subwoofer / LFE output of a receiver/processor.
- 7) Power Switch:
- Set to 'On' to power the subwoofer. Set to 'Off' to conserve energy when not in use for extended periods.
- 8) Power Input:
- Plug the power cord into an active, unswitched electrical outlet. Do not plug into accessory outlets on audio components.
Placing Your Subwoofer
Subwoofer performance is directly related to its placement in the listening room and its physical position relative to other speakers. Room reflections, standing waves, and absorptions strongly influence performance. Corner placement (1) generally maximizes bass, but can also increase destructive standing wave effects. Placing the subwoofer along the same plane as the left and right speakers (2) can improve integration. Placement behind the listening position (3) may also yield good results.
Experiment with placement before choosing a final location. Temporarily place the subwoofer in the listening position, play music with strong bass, and move around the room to find the location with the best bass performance.
Diagram illustrating subwoofer placement options: 1. Corner placement, 2. Along the same plane as front speakers, 3. Behind the listening position.
Connecting Your Subwoofer
To a Receiver or Preamp/Processor with a Low-Pass Filtered Dedicated Subwoofer Output (LFE):
Diagram showing connection: Receiver/Processor LFE OUT to Subwoofer INPUT via LFE cable. Note: This cable is not included but can be purchased from an electronics retailer.
To a Receiver or Preamp/Processor with Preamp Outputs:
Diagram showing connection: Receiver/Processor PREAMP OUTPUT to Subwoofer INPUT via RCA cables. An RCA Y-Adapter cable can also be used. Note: This cable is not included but can be purchased from an electronics retailer.
Notes for Preamp Output Connection: Be sure to turn the Subwoofer's Crossover fully clockwise when using this connection type, as it bypasses the subwoofer's internal crossover. Check your receiver or processor menu settings and set the subwoofer selection to 'On' or 'Yes.' Review your receiver or processor's manual for more information on speaker setup and configuration. We recommend setting the subwoofer's Crossover to 80Hz for mid-sized speakers, higher for smaller (satellite) speakers, and lower for larger floorstanding speakers.
Operating the Subwoofer
Turning the Subwoofer On and Off
Set the Power Switch to 'On'. Set the Power Mode to 'Auto'. The subwoofer will automatically turn on with an audio signal and enter Standby after 10 minutes of no signal. The LED glows blue when On and red when in Standby. For extended periods of non-use, set the Power Switch to 'Off'.
Subwoofer Adjustments: Crossover
The Crossover control adjusts the built-in low-pass filter between 50Hz and 150Hz. A higher setting increases the subwoofer's operating frequency and bass overlap with speakers, aiding a smooth bass transition. Adjust for a smooth bass response, lowering if bass is too strong, or raising if too weak.
Subwoofer Adjustments: Volume
Use the volume control to set the subwoofer's volume. Turn clockwise to increase, counter-clockwise to decrease. Balance with other speakers; this setting should not need frequent changes. For optimal volume, listen to music and films with strong bass content and find a 'middle ground' level. If the subwoofer consistently seems too loud or too quiet, consider repositioning it; corner placement tends to increase bass output, while placement away from walls or corners lessens it.
Subwoofer Adjustments: Phase
The Phase switch determines if the subwoofer driver's action is in phase with the speakers. Out-of-phase operation can cancel sound waves, reducing bass performance and sonic impact. While 'Normal' is often suitable, the best setting depends on your system and room. For clearest sound and maximum impact, listen to music you know well and select the phase position that gives drums and other percussive sounds the most impact.
Using the Supplied Carpet Spikes
Four metal spikes are supplied for carpeted surfaces. Do not use on non-carpeted surfaces. To insert spikes: 1. Gently lay the subwoofer on its side on a soft, nonabrasive surface. 2. Screw each spike into the threaded insert in each foot, ensuring they are fully screwed in for stability. Note: Never drag the subwoofer; always lift and carry it.
JBL Arena SUB 100P Overview
Don't forget the bass.
The JBL Arena SUB 100P delivers powerful bass with its 10" (250mm) high-output polycellulose woofer and dual rear ports that optimize bass performance. The 100W high-efficiency Class-D amplifier features unobtrusive rear-mounted controls for easy setup and seamless integration.
Image of the JBL Arena SUB 100P powered subwoofer, available in black and white finishes.
Features
- The signature punch and accuracy of JBL bass
- Understated, contemporary look and feel
- An audio powerhouse at an affordable price
- Just one part of an even more powerful system
Specifications
- 10" (250mm) Polycellulose Low-Frequency Woofer
- Power: 100W RMS (200W Dynamic)
- Frequency Response: 41Hz - 150Hz
- Crossover Frequencies: 50Hz - 150Hz (variable), 24 dB/octave
- Controls: Auto Power, Crossover, Level, Phase
- Input: One (1) Line-Level LFE Input
- Enclosure Type: Bass-Reflex via Rear-Firing Ports
- Power Requirement: 100V-240V, 50/60Hz
- Power Consumption (Idle/Full/Power): <0.5W (standby) / 160W/2.1A (max - 120V) / 160W/1.5A (max - 230V)
- Dimensions (H x W x D): 14-5/16" x 14-1/2" x 16" (364mm x 368mm x 406mm)
- Weight: 24 lbs (10.9 kg)
Important Safety Instructions
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Do not block any ventilation openings. Install in accordance with manufacturer's instructions.
- Do not install near heat sources like radiators, stoves, or other apparatus that produce heat.
- Do not defeat the safety purpose of polarized or grounding-type plugs. Consult an electrician for outlet replacement if the plug does not fit.
- Protect the power cord from being walked on or pinched.
- Use only manufacturer-specified attachments/accessories.
- Use only with specified carts, stands, tripods, brackets, or tables. Use caution when moving cart/apparatus combinations to avoid tip-over injury.
- Unplug during lightning storms or when unused for long periods.
- Refer all servicing to qualified personnel. Servicing is required if the apparatus is damaged, liquid has been spilled, objects have fallen into it, or it has been exposed to rain or moisture, does not operate normally, or has been dropped.
- Do not expose to dripping or splashing; ensure no liquid-filled objects are placed on the apparatus.
- To disconnect completely from AC mains, disconnect the power-supply cord plug from the AC receptacle.
- The mains plug of the power-supply cord shall remain readily operable.
- Do not expose batteries to excessive heat such as sunshine or fire.
Regulatory and Compliance Information
Caution
[Warning Symbol] RISK OF ELECTRIC SHOCK. DO NOT OPEN. The lightning flash with an arrowhead symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
FCC and IC Statement (USA and Canada)
This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by HARMAN could void the user's authority to operate the equipment.
RF Energy Statement
This equipment complies with FCC/IC RSS-102 radiation exposure limits for an uncontrolled environment. Install and operate with a minimum distance of 20cm between the radiator and your body.
Laser Safety (for CD/DVD/Blu-ray Disc™ Players)
Caution: This product uses a laser system. To prevent direct exposure to the laser beam, do not open the cabinet enclosure or defeat any safety mechanisms. Do not stare into the laser beam. Read the owner's manual carefully and retain it for future use. Refer servicing to qualified personnel only.
CLASS 1 LASER PRODUCT
Hearing Loss Prevention (For All EU Countries)
Caution: Permanent hearing loss may occur if earphones or headphones are used at high volume for prolonged periods. To prevent possible hearing damage, do not listen at high volume levels for long periods.
Environmental Compliance
WEEE Notice: This product must not be disposed of with household waste. Dispose of electronic waste at designated collection points for recycling. Proper recovery helps conserve natural resources and ensures safety for human health and the environment. Contact your local city center, household waste disposal service, or the shop where you purchased the equipment for more information.
RoHS Compliance: This product complies with Directive 2011/65/EU.
Battery Directive 2006/66/EC: Batteries must be disposed of in an environmentally sound manner. Contact local waste-management officials for information. WARNING: Danger of explosion if battery is incorrectly replaced. Do not disassemble, crush, puncture, short external contacts, or expose to excessive heat.
Symbols indicating mercury (Hg), cadmium (Cd), or lead (Pb) content in batteries are shown. The symbol indicating 'separate collection' for batteries is the crossed-out wheeled bin.
Declaration of Conformity: HARMAN International declares that this equipment complies with relevant directives (e.g., 2004/108/EC, LVD 2006/95/EC, ErP 2009/125/EC, RoHS 2011/65/EU). The declaration of conformity may be consulted on the HARMAN website.
For Products with Wireless Operation: HARMAN International declares compliance with Directive 1999/5/EC, ErP 2009/125/EC, and RoHS 2011/65/EU.
For All Products Except Those with Wireless Operation: HARMAN International declares compliance with EMC Directive.
CE mark is present.
HARMAN International Industries, Incorporated, 8500 Balboa Boulevard, Northridge, CA 91329 USA. www.jbl.com
