BN-LINK CP-UIH06-1 Digital Repeat Cycle Timer
Product Number: CP-UIH06-1
Product Ratings
Rated Voltage: 125V, 60Hz
Max. Loading: 15A/1875W Resistive, 10A/1250W Tungsten, 1/2HP
Warnings
- Use a grounded outlet
- Follow local electrical codes
- For indoor use only
- Keep children away
- Unplug timer before cleaning
- Fully insert plug
- Do not use in wet locations
- Do not exceed electrical ratings
A. Initial Set Up
Part 1 - Reset the Timer
Press and hold the R button on the side of the timer for 3 seconds.
Display Example: Digital display showing "12:00" with "OFF" and "AM" indicators.
Note: At this stage, no work mode will be displayed or executed.
Part 2 - Set the Current Time
Press and hold the MODE button, then press the HOUR button simultaneously to set the hour. The hour cycles from 12 AM to 11 PM.
Press and hold the MODE button, then press the MINUTE button simultaneously to set the minute. The minute cycles from 00 to 59.
Note: You can set the current time in the time interface or during other CYCLE operations but not in CTD working mode.
B. Product Functions and Set Up Instructions
Function 1 - Setting Daily ON-OFF Timing
1.1 Enter the Setting Mode
Press and hold the TIMED button to enter the mode.
Display Example: Digital display showing "0:00" for ON time and "0:00" for OFF time, with "AM" and "PM" indicators. The top row indicates "ON", and the bottom row indicates "OFF".
1.2 Set the ON Time
The top row "1 ON" will blink.
Press and hold the HOUR button to set the hour.
Press and hold the MINUTE button to set the minutes.
1.3 Set the OFF Time
Press the TIMED button to switch to the bottom row "1 OFF".
Press and hold the HOUR button to set the hour.
Press and hold the MINUTE button to set the minutes.
1.4 Set Additional Groups
Press the TIMED button to cycle through the settings for 2 ON, 2 OFF, 3 ON, and 3 OFF.
After 3 OFF, it will return to 1 ON.
1.5 Exit & Confirm Timer Group Setting
Press and hold the TIMED button in any blinking interface to exit or confirm.
The device will automatically switch to CYCLE TIMED working mode.
1.6 Clear or Restore Settings
Press the CTD button in any setting interface to clear or restore settings.
Cleared settings will display as "--:--."
1.7 Default Settings
The last saved settings will display upon entering the setting interface. If no settings exist, "--:--" will be displayed.
Display Example: Digital display showing "--:--" for the upper row and "8:20" for the lower row (current time).
Function 2 - Cycle Duration Setting
2.1 Enter the Setting Mode
Press and hold the CYCLE button.
2.2 Select Time Format
Press the "MODE" button to choose between H:M (hours and minutes) or M:S (minutes and seconds).
Display Examples:
- H:M format: Digital display showing "00:01" ON and "00:02" OFF.
- M:S format: Digital display showing "00:01" ON and "00:02" OFF.
2.3 Set ON Time
The upper row ON will blink.
Press and hold the HOUR and MINUTE buttons to set the desired time.
2.4 Set OFF Time
Press the CYCLE button to switch to the lower row OFF.
Long press the HOUR and MINUTE buttons to set the desired time.
2.5 Return to ON Time
Press the CYCLE button again to return to the upper row ON setting.
2.6 Exiting CYCLE Setting Mode
To exit, long press the CYCLE button.
The device will automatically switch to CYCLE TIMED working mode upon exit.
Default Display: If no timer group information has been set, the upper row will display "--:--."
Function 3 - Working Mode and Switching
3.1 Switching Between Modes
Press and hold the MODE button to switch modes.
After the initial long press, a short press of the MODE button will cycle through the modes.
If no buttons are pressed for 3 seconds, the device will automatically lock the current mode and start operating.
3.2 Mode Switching Sequence
- TIME INTERFACE (OFF, no functions active)
- CYCLE TIMED
- CYCLE CONTINUOUS
- CYCLE PERIOD
- TIMED
- Back to Time Interface (OFF)
3.3 Cycle Timed Mode
Requires: On-Off timing items & Cycle duration settings
Example: ON-OFF Timing: 8:00 AM ON ~ 5:00 PM OFF. Cycle Duration: 1 minute ON, 2 minutes OFF.
Display Example: Digital display showing "5:00" for OFF time and "8:20" for current time, with "PM", "Next", "OFF", "AM", "TIMED" indicators. The "CYCLE" indicator is flashing. Text indicates the timer will turn off at 5:00 PM.
Output Status: Repeats 1 minute ON / 2 minutes OFF continuously from 8:00 AM to 5:00 PM.
3.4 Cycle Continuous Mode
Requires: Cycle duration settings
Example: 1 minute ON, 2 minutes OFF.
Display Example: Digital display showing "00:01" for ON time and "8:20" for current time, with "ON", "AM", "H:M", "CONTINUOUS", "CYCLE" indicators. Text indicates the current time is 8:20 AM, operating in CYCLE CONTINUOUS mode, with the CYCLE indicator flashing.
3.5 Cycle Period Mode
Requires: On-Off timing items & Cycle duration settings
Cycle Period Setting: When switched to the CYCLE PERIOD working mode, the setting interface will pop up first (Different from the other three working modes).
The upper row shows the cycle interval, supporting only the H:M format.
Display Example: Digital display showing "00:01" for ON time and "8:20" for current time, with "ON", "AM", "H:M", "PERIOD", "CYCLE" indicators. Text indicates the current cycle is in the ON period, with 1 minute remaining, and the number updates every minute. The current time is 8:20 AM, and it is in CYCLE PERIOD mode, with the CYCLE character flashing.
Setup: Press the HOUR button to set the hours and the MINUTE button to set the minutes, with long press for fast adjustment. The default display will show the last saved setting each time you enter.
After setting, short press the CYCLE button to complete the setup and start the CYCLE PERIOD.
In the setting interface, short press the MODE button will switch to the TIMED working mode. (If the PERIOD time is changed, the settings will be saved.)
Example: Cycle: The device will turn ON at H:M 00:01 and OFF at 00:02. Interval: The set time is H:M 30:00, representing a 30-hour duration.
3.6 Timed Mode
Requires: Cycle duration settings
Example: Timed - 8:00 AM ON ~ 5:00 PM OFF.
Example Display: Digital display showing "5:00" for OFF time and "8:20" for current time, with "PM", "Next", "OFF", "AM", "TIMED" indicators. Text indicates the timer will turn off at 5:00 PM.
Output Status: The output remains on between 8:00 AM and 5:00 PM.
Function 4 - Countdown Function
Activate Countdown
Press and hold the CTD button for 2 seconds in the time interface or any working mode.
Display Example: Digital display showing "20:00" for countdown time and "8:20" for current time, with "ON", "OFF", "AM", "H:M", "CTD" indicators. Text indicates the numbers blink and the current time is displayed without the CYCLE character.
Left side: Choose ON or OFF. Press the MODE button to switch.
CTD ON: Indicates countdown on mode. Socket output is turned on first, then off after the countdown ends. This repeats daily.
CTD OFF: Indicates countdown off mode. Socket output is turned off first, then on after the countdown ends. This repeats daily.
To reset the countdown, short press the TIMED button to immediately set the countdown time to 00:00.
Countdown Operation
Example Display 1: After setting the countdown (time not 00:00), short press the CTD button to start the countdown immediately.
Display: Digital display showing "20:00" for countdown time and "8:00" for current time, with "ON", "AM", "H:M", "CTD" indicators. Text indicates countdown remaining time is 20 hours, product is ON, "CTD" blinks, and numbers change every minute. Displays the current time.
Example Display 2: Digital display showing "04:00" for countdown time and "4:00" for current time, with "OFF", "AM", "H:M", "CTD" indicators. Text indicates countdown remaining time is 4 hours, product is OFF, "CTD" is steady, and numbers change every minute. Displays the current time.
Note: This screen shows the countdown in CTD ON mode after the work time ends, initiating the rest time countdown until the next cycle.
Countdown Exit
Press and hold the CTD button to exit.
Function 5 - Always ON Function
Always ON can be used if the product is for regular socket use.
Press and hold the MINUTE button for 2 seconds in the time interface or any CYCLE mode.
In CTD mode, first hold the CTD button to exit countdown mode.
Display: Digital display showing "On" in the center and "8:00" for current time, with "AM" indicator. Text indicates "On" in the center indicates Always ON.
To exit, press and hold the MINUTE button for 2 seconds again.
C. WARRANTY
30-Day Money-Back Guarantee: If you are not satisfied with your purchase, you can request a refund within 30 days.
12-Month Warranty: The device must have been used under proper technical conditions. Covers failures and defects not caused by human error.
D. CONTACT US
For any problems during use, please contact BN-LINK INC. at support@bn-link.com.
BN-LINK INC.
Address: 17890 Castleton St, Suite 228, City of Industry, CA 91748
Customer Support:
- U.S. Domestic: 424-279-6074
- International: +1 888-491-5507
- E-mail: support@bn-link.com
- Web: www.bn-link.com
Working Hours: 9 AM - 5 PM PST, Mon - Fri
Designed in California | Made in China
