Shelly Wall Display

User and Safety Guide

Read before use: This document contains important technical and safety information about the device, its safe use and installation.

⚠️ CAUTION! Before beginning the installation, please read carefully and entirely this guide and any other documents accompanying the device. Failure to follow the installation procedures could lead to malfunction, danger to your health and life, violation of law or refusal of legal and/or commercial guarantee (if any). Shelly Europe Ltd is not responsible for any loss or damage in case of incorrect installation or improper operation of this device due to failure of following the user and safety instructions in this guide.

Product Introduction

Shelly® is a line of innovative microprocessor-managed devices, which allow remote control of electric circuits through a mobile phone, tablet, PC, or home automation system. Shelly® devices can work standalone in a local Wi-Fi network or they can also be operated through cloud home automation services. Shelly Cloud is a service that can be accessed using either an Android or iOS mobile application or with any internet browser at https://control.shelly.cloud/.

Shelly® devices can be accessed, controlled, and monitored remotely from any place where the user has internet connectivity, as long as the devices are connected to a Wi-Fi router and the Internet. Shelly® devices have an Embedded Web Interface accessible at http://192.168.33.1 when connected directly to the device access point, or at the device IP address on the local Wi-Fi network. The embedded Web Interface can be used to monitor and control the device, as well as adjust its settings.

Shelly® devices can communicate directly with other Wi-Fi devices through HTTP protocol. An API is provided by Shelly Europe Ltd. For more information, please visit: https://shelly-api-docs.shelly.cloud/#shelly-family-overview.

Shelly® devices are delivered with factory-installed firmware. If firmware updates are necessary to keep the devices in conformity, including security updates, Shelly Europe Ltd will provide the updates free of charge through the device Embedded Web Interface or the Shelly mobile application, where the information about the current firmware version is available. The choice to install or not to install the device firmware updates is the user's sole responsibility. Shelly Europe Ltd shall not be liable for any lack of conformity of the device caused by failure of the user to install the provided updates in a timely manner.

Shelly Wall Display is a smart home control panel with a color display and load circuit switching functionality.

Installation Instructions

⚠️ CAUTION! Danger of electrocution. Mounting/installation of the Device to the power grid has to be performed with caution, by a qualified electrician.

⚠️ CAUTION! Danger of electrocution. Every change in the connections has to be done after ensuring there is no voltage present at the Device terminals.

⚠️ CAUTION! Use the Device only with a power grid and appliances that comply with all applicable regulations. A short circuit in the power grid or any appliance connected to the Device may damage it.

⚠️ CAUTION! Do not connect the Device to appliances exceeding the given max load!

⚠️ CAUTION! Connect the Device only in the way shown in these instructions. Any other method could cause damage and/or injury.

⚠️ CAUTION! Do not install the Device where it can get wet.

? RECOMMENDATION: Connect the Device using solid single-core cables or stranded cables with ferrules. The cables should have insulation with increased heat resistance, not less than PVC T105°C (221°F).

⚠️ CAUTION! The Device and the load current circuit has to be secured by a cable protection switch in accordance with EN60898-1 (tripping characteristic B or C, max. 5 A rated current, min. 6 kA interrupting rating, energy limiting class 3).

Before starting the mounting/installation of the Device, check that the breakers are turned off and there is no voltage on their terminals. This can be done with a phase tester or multimeter. When you are sure that there is no voltage, you can proceed to connecting the wires.

Wiring Diagram Description (Figure 1)

The diagram shows the connections for the Shelly Wall Display. The Live (L) wire from the 230 VAC power source connects to the device's L terminal. The Neutral (N) wire from the power source connects to the device's N terminal. A switch or button can be connected between the device's SW terminal and the Live (L) wire.

Installation Steps

1. Connect the wires to the power module according to the wiring diagram. Connect the Live wire to the Device L terminal, and the Neutral wire to the N terminal. Connect a switch or a button to the Device SW terminal and the Live wire.
2. Insert the power module with the wires into the wall box and fix it with the supplied screws. (Illustrated in Figure 3)
3. Remove the screw at the bottom of the display module. (Illustrated in Figure 4)
4. Attach the display module by pressing it against the power module until you hear a click. ⚠️ CAUTION! Be very careful not to bend the header pins when inserting them into the display module header connector.
5. Replace the screw into the display module and fasten it to prevent accidental detachment.

Initial Inclusion

If you choose to use the Device with the Shelly Smart Control mobile application and cloud service, instructions on how to connect the Device to the Cloud and control it through the Shelly Smart Control app can be found in the mobile application guide. The Shelly mobile application and Shelly Cloud service are not conditions for the Device to function properly. This Device can be used standalone or with various other home automation platforms and protocols.

⚠️ CAUTION! Do not allow children to play with the Device and the buttons/switches connected to the Device. Keep the devices for remote control of Shelly (mobile phones, tablets, PCs) away from children.

Specifications

• Dimensions (Height x Width x Depth): 85x85x30mm / 3.35x3.35x1.18 in
• Ambient Temperature: -20 °C to 40 °C / -5 °F to 105 °F
• Humidity: 30 % to 70 % RH
• Maximum Altitude: 2000 m / 6562 ft
• Power Supply: 230 VAC, 50/60Hz
• Electrical Consumption: < 1 W
• Max. Switching Current: 5 A
• Power Measurement: No
• External Protection: max. 5 A, tripping characteristic B or C, 6 kA interrupting rating, energy limiting class 3
• RF Band: 2400 - 2495 MHz
• Max. RF Power: < 20 dBm
• Wi-Fi Protocol: 802.11 b/g/n
• Wi-Fi Operational Range (depending on local conditions):
  • up to 50 m / 160 ft outdoors
  • up to 30 m / 100 ft indoors
• Bluetooth Protocol: 4.2
• Bluetooth Operational Range (depending on local conditions):
  • up to 30 m / 100 ft outdoors
  • up to 10 m / 33 ft indoors
• Schedules: 20
• Webhooks (URL Actions): 20 with 2 URLs per hook
• Scripting: No
• MQTT: Yes

Declaration of Conformity

Hereby, Shelly Europe Ltd. declares that the radio equipment type Shelly Wall Display is in compliance with Directive 2014/53/EU, 2014/35/EU, 2014/30/ EU, 2011/65/EU.

The full text of the EU declaration of conformity is available at the following internet address: https://shelly.link/wall-display_DoC

Manufacturer: Shelly Europe Ltd.

Address: 103 Cherni vrah Blvd., 1407 Sofia, Bulgaria

Tel.: +359 2 988 7435

E-mail: support@shelly.cloud

Official website: https://www.shelly.cloud/

Changes in the contact information data are published by the Manufacturer on the official website. All rights to the trademark Shelly® and other intellectual rights associated with this Device belong to Shelly Europe Ltd.

Legend

Device Terminals:

• O: Output terminal
• SW: Switch input terminal
• L: Live terminal
• N: Neutral terminal

Wires:

• N: Neutral wire
• L: Live (230 VAC, 50/60 Hz) wire