Trusda LS2C.M2 Power Bank Instruction Manual

Product Overview

This document provides instructions for the Trusda LS2C.M2 power bank. The power bank has an unfolded size of 160x120mm and a folded size of 80x120mm. It is made of 100g writing paper with double-sided single-color printing and accordion folding.

Product Name: LS2C.M2

Capacity: 10000mAh@3.85V, 38.5Wh

Rated Power: 20W

Features:

• Supports wireless charging technology with a built-in induction coil.
• Compatible with various wireless charging devices and devices supporting 5V, 9V, 12V DC input.
• Built-in battery protection circuit with overcharge, over-discharge, overload, and short-circuit protection for high safety.
• Efficient DC-DC step-up conversion circuit for output.
• Features like automatic power-off, LED display, and ultra-low power consumption standby.

LED Introduction

• Power on Standby: Blue light
• Output by: Blue light keeps on
• Output abnormal load: Blue light flashing
• Charging: White LED flashing
• Power display: White LED shows current power (4 white LEDs bright when fully charged)
• Wireless Charging Indicators: Green light indicates wireless charging standby; Blue light long bright when wireless charging is active.

Accessory List

• USB-C to USB-C charging cable x1

Basic Instructions for Product Operation

• Charging the power bank: The white LED will flash while charging and show the current power when fully charged.
• Load status: When a device is connected, the product automatically identifies and outputs power, indicated by a solid white LED.
• Simultaneous charging and releasing: Most main equipment supports this. For special equipment, it must be confirmed. During this time, both output and input voltage are limited to 5V.
• Wireless Charging:
  • To enable wireless charging for compatible devices, place the device on the coil. The green light indicates standby.
  • When a device is placed on the coil, wireless charging activates automatically. The blue light will be solid.
  • If using C line/C port with a load, magnetic suction wireless charging requires a key press to start. The C line/C port will be limited to 5V, and magnetic suction wireless charging to 5W. When the C line/C port load is removed, magnetic suction wireless charging restores to 15W.
• Foreign Body Detection: The product has a foreign body detection function. If a metal item is placed on the coil, the output will automatically close, and the white light will flash. It stops flashing after the foreign body is removed.
• Low Battery Voltage: When the battery voltage is lower than 3.5V, the Q value induction function of magnetic suction wireless charging is turned off. Clicking the key will enable magnetic suction wireless charging.

Precautions

• Read this specification carefully before using the product.
• Use the power bank within the specified charging and discharging rated specifications and ambient temperature.
• Keep accessories away from children.
• Keep away from flammables and explosives when using the product.
• Use only the specified charger and approved accessories to avoid damage to electronic products and the power bank.
• Use the mobile power supply properly according to local laws and regulations. In situations like aircraft landing or near medical instruments, avoid charging and turn off the device immediately.
• If the product is abnormal (e.g., package damage, deformation, smell of electrolyte, leakage), stop using it immediately.
• Do not dispose of used mobile power in regular trash; use designated battery recycling bins.

Safety Warnings

• Avoid short-circuiting the product interface.
• Avoid charging the product for a long time after it is fully charged. Remove the charger promptly.
• Do not throw, impact, or damage the product. If the product is sunken, perforated, cracked, or shows other damage, stop using it immediately.
• Do not disassemble or modify the product.
• Keep the product in a dry environment and away from corrosive substances.
• It is forbidden to put the product in high-temperature environments (e.g., near heat sources or in direct sunlight).
• Products used frequently in humid, low-temperature, or high-temperature environments should be scrapped within 18 months. If still needed, professional certification is required. The longest service life is 24 months.

FCC Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Disclaimers

The manufacturer is not responsible for equipment damage and safety problems caused by:

• Not following the operation instructions and safety warnings.
• Damage caused by using the product in environments beyond the specified conditions.
• Damage caused by storage conditions not meeting the requirements.
• Unauthorized modifications or repairs.
• Damage caused by external factors such as lightning strikes or power surges.

For FAQs and more information, please visit: www.trusda.com/support

Specifications

Tolerance Table

Product Number: LS2C.M2

Product Name: Mobile Power

Material:

Scale: mm

Drawn by:

Approved by:

Date: 2025-03-10

Manufacturer Information

Manufacturer: Shenzhen Trusda Industrial Co., Ltd.