Lark Manor Dresser Installation and Assembly Guide
Model Numbers: bbov6271, W114504700
Thank you for purchasing our products. Please contact us if you have difficulty with assembly or need replacement parts. Our customer service is here to assist you.
BOARD IDENTIFICATION
| Part Number | Quantity |
|---|---|
| 1 | 1x1 |
| 2 | 2x1 |
| 3 | 3x1 |
| 4 | 4x1 |
| 5 | 5x1 |
| 6 | 6x1 |
| 7 | 7x2 |
| 8 | 8x1 |
| 9 | 9x1 |
| 10 | 10x1 |
| 11 | 11x1 |
| 12 | 12x8 |
| 13 | 13x12 |
| 14 | 14x12 |
| 15 | 15x8 |
| 16 | 16x4 |
| 17 | 17x4 |
| 18 | 18x4 |
| 19 | 19x8 |
| 20 | 20x4 |
| 21 | 21x1 |
| 22 | 22x1 |
Hardware Identification
- A: Cam bolt (X98)
- B: Cam lock (X98)
- C: Wood dowel (M6X30, X12)
- D: Screws (M4X35, X64)
- E: Screws (M3.5X12, X96)
- F: Screws (X16)
- G: Screws (X12)
- H: Screws (X16)
- I: Screwdriver (X2)
Installation of Eccentric Wheel Nut Set
Step 1:
Screw the end of cambolt on the board, find the corresponding board and insert the other end.
Diagram shows a cambolt being screwed into a board.
Step 2:
Stuff the camlock into the round hole. The arrowpoints to the cambolt.
Diagram shows a camlock being inserted into a hole, with an arrow indicating alignment with the cambolt.
Step 3:
Turn clockwise about 180° to lock the plate.
Diagram shows a camlock being rotated clockwise with a screwdriver to secure a connection.
INSTALLATION STEPS
STEP 1:
Install the screws (E) from the second hole from the left and the fifth hole from the right on G-LEFT-1. Install the screws (E) from the fifth hole from the left and the second hole from the right on G-RIGHT-1.
Diagram shows two long panels (G-LEFT-1 and G-RIGHT-1) with multiple screw holes. Screws (E) are depicted being inserted into specific holes on both panels. Quantities of E (X16) and G (X4) are shown.
STEP 2:
Attach panels using Cam bolts (A) and Wood dowels (C).
Diagram shows multiple panels being assembled. Cam bolts (A) are shown being inserted into holes, and Wood dowels (C) are also shown. Quantities of A (X20) and C (X4) are indicated.
STEP 3:
G-LEFT-1: Install the screws (E) from the third hole from the left and the fourth hole from the right. G-RIGHT-1: Install the screws (E) from the fifth hole from the left and the second hole from the right.
Diagram shows panels being assembled with screws (E) inserted into specific holes. A 180° rotation symbol is shown, indicating orientation. Quantities of E (X16) and G (X4) are indicated.
STEP 4:
Attach panels using Cam bolts (A) and Wood dowels (C).
Diagram shows panels being assembled with Cam bolts (A) and Wood dowels (C) being inserted. A 180° rotation symbol is shown. Quantities of A (X4) and C (X2) are indicated.
STEP 5:
G-LEFT-1: Install the screws (E) from the second hole from the left and the fifth hole from the right. G-RIGHT-1: Install the screws (E) from the fourth hole from the left and the third hole from the right.
Diagram shows panels being assembled with screws (E) inserted into specific holes. A 180° rotation symbol is shown. Quantities of E (X16) and G (X4) are indicated.
STEP 6:
Attach panels using Cam bolts (A) and Wood dowels (C).
Diagram shows panels being assembled with Cam bolts (A) and Wood dowels (C) being inserted. A 180° rotation symbol is shown. Quantities of A (X4) and C (X2) are indicated.
STEP 7:
Attach panels using Cam locks (B).
Diagram shows panels (3 and 8) being joined. Cam locks (B) are shown being inserted and secured. Quantity of B (X4) is indicated.
STEP 8:
Attach panels using Screws (D).
Diagram shows panels (3, 4, and 9) being joined with Screws (D). Quantity of D (X4) is indicated.
STEP 9:
Attach panels using Cam bolts (A) and Wood dowels (C).
Diagram shows panel (6) being prepared with Cam bolts (A) and Wood dowels (C). Quantities of A (X6) and C (X4) are indicated.
STEP 10:
Attach panels using Cam locks (B).
Diagram shows panels (6, 10, and 11) being joined with Cam locks (B). Quantity of B (X6) is indicated.
STEP 11:
Attach panels using Screws (D).
Diagram shows panels (3, 4, and 6) being joined with Screws (D). Quantity of D (X4) is indicated.
STEP 12:
Attach panels using Cam locks (B).
Diagram shows panels (3 and 7) being joined with Cam locks (B). Quantity of B (X2) is indicated.
STEP 13:
Attach panels using Cam locks (B).
Diagram shows panels (2, 6, 7, 9, 10, 11) being joined with Cam locks (B). Quantity of B (X10) is indicated.
STEP 14:
Slide panel (22) into place.
Diagram shows panel (22) being inserted into the partially assembled structure.
STEP 15:
Attach panels using Cam locks (B).
Diagram shows panels (4 and 7) being joined with Cam locks (B). Quantity of B (X2) is indicated.
STEP 16:
Attach panels using Cam locks (B).
Diagram shows panels (5, 6, 9, 11) being joined with Cam locks (B). Quantity of B (X10) is indicated.
STEP 17:
Insert panel (21) into place.
Diagram shows panel (21) being inserted into the structure.
STEP 18:
Attach panel (1) using Cam bolts (A).
Diagram shows panel (1) being prepared with Cam bolts (A). Quantity of A (X8) is indicated.
STEP 19:
Attach panels using Cam locks (B).
Diagram shows panels (1, 2, 3, 4, 5) being joined with Cam locks (B). Quantity of B (X8) is indicated.
STEP 20:
Attach panels (12 and 16) using Cam bolts (A).
Diagram shows panels (12 and 16) being prepared with Cam bolts (A). Quantities of A (x8 for panel 12, x4 for panel 16) are indicated.
STEP 21:
Attach panels using Screws (D).
Diagram shows panels (13, 14, 15, 17, 18) being joined with Screws (D). Quantities of D (x4 for 13, x8 for 15, x4 for 17, x4 for 18) are indicated.
STEP 22:
Assemble drawer components.
Diagram shows drawer parts (19 and 20) being assembled. Quantity of 19 (x8) and 20 (x4) are indicated.
STEP 23:
Attach panels using Cam locks (B).
Diagram shows drawer side panels being joined with Cam locks (B). Quantities of B (x4 for one set, x8 for another) are indicated.
STEP 24:
Attach drawer fronts using Screws (F).
Diagram shows drawer fronts being attached to drawer boxes using Screws (F). Quantities of F (x16 for one set, x8 for another) are indicated.
STEP 25:
G-LEFT-2: Install screws (E) from the first hole from the left and the fourth hole from the right. G-RIGHT-2: Install screws (E) from the fourth hole from the left and the first hole from the right.
Diagram shows drawer box assemblies (G-LEFT-2 and G-RIGHT-2) with screws (E) being inserted. Quantities of E (X48) and G (X12) are indicated.
STEP 26:
Insert assembled drawers into the dresser frame.
Diagram shows the dresser frame with arrows indicating the insertion of multiple assembled drawers.
STEP 27:
Attach the back panel.
Diagram shows the back of the dresser with a panel being attached using hardware (H).
STEP 28:
Secure the dresser to the wall using the provided anti-tip hardware (I).
Diagram shows the dresser positioned against a wall, with close-ups illustrating the attachment of anti-tip brackets to the dresser and the wall using Screwdriver (I). A drill symbol is also shown, indicating wall mounting.
