ASSEMBLY INSTRUCTIONS

Important Notice

This product contains small components; please ensure they are kept away from small children.

IMPORTANT SAFETY INFORMATION: PLEASE READ BEFORE ASSEMBLY AND KEEP FOR FUTURE REFERENCE.

• Read each step carefully. It is very important that each step of instruction is performed in the correct order. If these steps are not followed in sequence, assembly difficulties will occur.
• Make sure all parts are included. Most parts are labelled or stamped on the raw edge.
• Work in a spacious area, preferably on a carpet, near the place the unit will be used.
• Do not use power tools to assemble your furniture. Power tools may strip or damage the parts.
• Move your new furniture carefully, with two people lifting and carrying the unit to its new location.
• Never push, drag, or pull your furniture (especially on carpet).

PLEASE DO NOT RETURN PRODUCT TO US IMMEDIATELY

If a part is missing or damaged, email our customer service. We will gladly ship your replacement parts FREE of charge. For prompt, reliable service, please have your assembly instruction ready.

[warning] WARNING: Children have died from furniture tipover. To reduce the risk of furniture tipover:

• ALWAYS install anti-tip device provided.
• NEVER put a TV on this product.
• NEVER allow children to stand, climb or hang on any drawers, doors, or shelves.
• NEVER open more than one drawer at a time.
• Place heaviest items in the lowest drawers. This is a permanent label. Do not remove!

Tools Recommended

[two people] [screwdriver] [drill] [cross]

Parts List and Hardware

Diagram showing an exploded view of the dresser, illustrating all structural components (numbered 1-19) and the hardware (lettered A-P, CL-DR) required for assembly.

Step 1

Diagram shows attaching screws (A) to parts 6 and 7, then connecting part 8 to part 9 using screw (D) and tack glide (P).

Install the screw (A) on the part 6 & 7.

Connect part 8 to part 9 with screw (D), connect tack glide (P) to part 9 in clockwise to tighten.

Hardware: D x1, P x1, A x4

Step 2

Diagram shows inserting wooden dowel (C) into part 8, then connecting parts 6 and 7 to part 8. Cam locks (B) are inserted into part 8 and tightened with a screwdriver.

Insert wooden dowel (C) into part 8, then connect part 6 & 7 to part 8. Insert cam lock (B) into the corresponding holes on part 8 and use a screwdriver to turn it clockwise to tighten, the installation position is as shown.

Hardware: C x2, B x4

Step 3

Diagram shows attaching guide rails (CL and CR) to part 4 using screws (N). Guide rail CL is attached to the right side, and CR to the left side, with a 180-degree turn.

Firstly, lock the guide rail (CL) to the right side of the part 4 with screw (N), then turn it 180 degrees and lock the guide rail (CR) to the left side of the part 4 with the screw (N). The installation position is as shown. There is only one piece part 4.

Hardware: N x18, CL x3, CR x3

Step 4

Diagram shows installing screws (A) on the left and right sides of part 4.

Install screw (A) on the left and right sides of part 4, the installation position is as shown.

Hardware: A x8

Step 5

Diagram shows attaching guide rails (CL and CR) to parts 2 and 3 respectively, using screws (N).

Lock the guide rail (CL) on part 2 with screw (N), lock the guide rail (CR) on part 3 with screw (N).

Hardware: N x18, CL x3, CR x3

Step 6

Diagram shows inserting screws (A) into parts 2 and 3, and attaching mats (O) to the legs.

Insert screw (A) into corresponding holes on part 2 & 3, then attach mat (O) to the legs bottom as shown.

Hardware: O x4, A x16

Step 7

Diagram shows inserting wooden dowel (C) into part 4, then connecting part 4 to part 8 using screw (D).

Insert wooden dowel (C) into part 4, then connect part 4 to part 8 by screw (D), the installation position is as shown.

Hardware: C x2, D x2

Step 8

Diagram shows connecting part 5 (x2) to part 4 with cam locks (B). Cam locks are inserted into part 5 and tightened with a screwdriver.

Connect part 5 (x2) to part 4 with cam lock (B), insert cam lock (B) into the corresponding holes on part 5 (x2) and use a screwdriver to turn it clockwise to tighten, the installation position is as shown.

Hardware: B x4

Step 9

Diagram shows connecting part 10 to part 4 with screw (D), inserting dowel (C) into part 2, then connecting assembled parts 5 (x2), 10, 6, and 7 to part 2 using cam locks (B).

Connect part 10 to Part 4 with screw (D), insert the dowel (C) into part 2 firstly, then connect assembled part 5 (x2) & 10 & 6 & 7 to part 2 with cam lock (B), put the cam lock (B) into the corresponding holes on part 5 (x2) & 10 & 6 & 7 and use a screwdriver to turn it clockwise to tighten, the installation position is as shown.

Hardware: D x1, C x2, B x8

Step 10

Diagram shows connecting part 5 (x2) to part 4 with cam locks (B). Cam locks are inserted into part 5 and tightened with a screwdriver.

Connect part 5 (x2) to part 4 with cam lock (B), put the cam lock (B) into the corresponding holes on part 5 (x2) and use a screwdriver to turn it clockwise to tighten, the installation position is as shown.

Hardware: B x4

Step 11

Diagram shows inserting part 12 along the slot between parts 6 and 10.

Insert part 12 along the slot between part 6 & 10, the position is as shown.

Step 12

Diagram shows inserting dowel (C) into part 3, then connecting assembled parts 5 (x2), 10, 6, and 7 to part 3 using cam locks (B).

Insert the dowel (C) into part 3 firstly, then connect assembled part 5 (x2) & 10 & 6 & 7 to part 3 with cam lock (B), put the cam lock (B) into the corresponding holes on part 5 (x2) & 10 & 6 & 7 and use a screwdriver to turn it clockwise to tighten, the installation position is as shown.

Hardware: C x2, B x8

Step 13

Diagram shows inserting part 11 along the slot between parts 2 and 3. It also shows adjusting pad (P) on the middle leg, ensuring it is grounded.

Insert part 11 along the slot between part 2 & 3, the position is as shown.

Adjusting the pad (P) on the middle leg, please ensure that it is firmly grounded to prevent any potential dresser collapse caused by hanging.

Step 14

Diagram shows installing screw (A) on part 1 and fastening the L-shaped iron piece (I) with screw (J).

Install the screw (A) on the part 1, fasten the L-shaped iron piece (I) with screw (J).

Hardware: J x2, I x2, A x6

Step 15

Diagram shows inserting dowels (C) into parts 2, 3, and 4, then connecting these parts to part 1 using cam locks (B).

Insert the dowel (C) on part 2 & 3 & 4, then connect assembled parts ② & 3 & 4 to part ① with cam lock (B), put the cam lock (B) into the corresponding holes on part 2 & 3 & 4 and use a screwdriver to turn it clockwise to tighten, the installation position is as shown.

Hardware: C x6, B x6

Step 16

Diagram shows using screws (G) and (H) to fasten the back plate buckle.

Use the screws in component (G), (H) to fasten the back plate buckle. The installation position is as shown.

Hardware: G x20, H x20

Step 17

Diagram shows drilling holes on the wall and fixing the cabinet with expansion screws (L) and screws (K).

First drill holes on the wall where it is placed, then use expansion screw (L) to fix the cabinet with screw (K). The installation location is as shown.

Hardware: L x2, K x2

Step 18

Diagram shows installing screws (A) on drawer panels 19 (x3) and 13 (x3), then attaching handles (E) using screws (F).

Install the screw (A) on the drawer panels 19 (x3) & 13 (x3) firstly, then use the screw (F) to lock the handle (E) on the drawer panels 19 (x3) & 13 (x3).

Hardware: E x12, F x12, A x30

Step 19

Diagram shows connecting side panels 14, 15, and back panel 10 using screws (M). It also shows inserting the bottom plate 17 and connecting part 18 to part 16 with screw (M).

Use the screw (M) to connect the side panels 14 & 15 and the back panel 10.

Insert the bottom plate 17 along the slot, then connect part 18 to part 16 with screw (M).

Hardware: M x30

Step 20

Diagram shows inserting cam locks (B) into parts 14, 15, and 18, then tightening them with a screwdriver to assemble the drawer front plate 13.

Put the cam lock (B) into the corresponding holes on part 14 & 15 & 18 and use a screwdriver to turn clockwise to tighten, assemble the drawer front plate 13 to the drawer.

Hardware: B x15

Step 21

Diagram shows installing guide rails (DR and DL) on side panels 15 and 14 respectively, using screws (N).

Use the screw (N) to install the guide rail (DR) on the side panel 15 and install the guide rail (DL) on the side panel 14 with screw (N), the installation position is as shown.

Hardware: DL x3, DR x3, N x18

Step 22

Diagram shows inserting cam locks (B) into parts 14, 15, and 18, then tightening them with a screwdriver to assemble the drawer front plate 19.

Put the cam lock (B) into the corresponding holes on part 14 & 15 & 18 and use a screwdriver to turn clockwise to tighten, assemble the drawer front plate 19 to the drawer.

Hardware: B x15

Step 23

Diagram shows installing guide rails (DR and DL) on side panels 15 and 14 respectively, using screws (N).

Use the screw (N) to install the guide rail (DR) on the side panel 15 and install the guide rail (DL) on the side panel 14 with screw (N), the installation position is as shown.

Hardware: DL x3, DR x3, N x18