eufy S100 Wall Light Cam User Manual

At a Glance

Diagram showing the eufy S100 Wall Light Cam with numbered callouts pointing to its components: 1. Light, 2. Camera Lens, 3. Status LED, 4. Motion Sensor, 5. Micro-USB Port, 6. Reset Hole.

• 1. Light
• 2. Camera Lens
• 3. Status LED
• 4. Motion Sensor
• 5. Micro-USB Port
• 6. Reset Hole

What's Included

Illustrations of the included items: the S100 Wall Light Cam, a mounting base, screws for the base and camera, a USB cable, and a quick start guide.

• S100 Wall Light Cam
• Mounting Base
• Base Screw
• Camera Fixing Screw
• USB Cable
• Quick Start Guide

Setting Up the System

1. Open the USB port cover on the back of the device, then connect it to power with the provided cable. The status LED will display red when the device is ready for setup.

   Diagram showing the back of the device with the USB port cover open, connecting the USB cable to the device and a power source. An arrow indicates the status LED turning red.

2. Download and install the eufy Security app, then set up an account.

   Screenshot of a smartphone displaying the eufy Security app interface, with buttons to download from the App Store and Google Play.

3. Scan the QR code on the back of the device, then follow the on-screen instructions to complete the setup.

   Diagram showing a smartphone scanning a QR code on the back of the eufy S100 Wall Light Cam.

4. Disconnect the device from power and close the USB port cover, then secure the rubber plugs.

   Diagram showing the device being disconnected from power, the USB port cover being closed, and rubber plugs being inserted.

Installation

⚡Safety Warning: To avoid the risk of shock, injury, or death, always be cautious when working with electricity. Hire a professional electrician if you're uncomfortable working with electrical wiring.

1. Turn off the circuit breaker of your home. Turn the lights on and off to check the electricity in your home is properly turned off.

   Diagram showing a hand turning off a circuit breaker switch labeled 'OFF'. A light switch is also shown in the 'OFF' position.

2. Select a location for the device and mark it.

   Illustration of a doorway with a measurement line indicating the recommended installation height of 1.8m to 2m from the ground. A note indicates not to install higher than 2.2m.

   ? For the best motion detection experience, install the device between 1.8m and 2m above the ground. Do not install the device more than 2.2m above the ground.

3. If no wires exist, run wires to the installation location. Next, screw the mounting bracket onto the wall.

   • On wooden walls, do not pre-drill holes. Use the screws provided to fix the mounting bracket onto the wall.
   • For walls made of hard materials, such as stucco, brick, or concrete, pre-drill holes in the required locations, insert the provided anchors, and then use the provided screws to fix the mounting bracket to the wall.

   Diagram showing a mounting bracket being attached to a wall. One illustration shows drilling into a wall and inserting an anchor, then screwing the bracket. Another shows attaching directly to wood.

4. Loosen the wire screws, insert the neutral, ground, and live wires into the connectors, and then tighten the wire screws to thoroughly secure the wires.

   Diagrams showing the wire terminals on the mounting bracket. One shows loosening screws, inserting wires (labeled Ground, Neutral, Live), and tightening screws.

   Region	Ground	Neutral	Live
   North America	Green / Yellow	White	Black
   Europe	Green / Yellow	Blue	Brown

   Note: The wire colors vary depending on region.

Next Steps:

5. Mount the device onto the mounting bracket, and then secure it with a screw on each side.
6. Turn on the circuit breaker of your home.

Diagram showing the device being attached to the mounted bracket and secured with screws. Another diagram shows a hand turning on a circuit breaker switch labeled 'ON'.

Adjusting Angles

1. Rotate the device while checking the live stream from the eufy Security app until you get the desired view.

   Diagram showing the device being rotated left and right, with a smartphone displaying a live stream. Arrows indicate adjustment angles (e.g., 30°).

2. Adjust each light for different lighting effects.

   Diagrams showing the device's lights being adjusted to different angles and brightness levels, indicating various lighting effects.

Customer Service

For customer support, please refer to the following:

• Warranty: 12-month limited warranty.
• Contact Numbers:
  • US: +1 (800) 988-7973
  • UK: +44 (0) 1604 936200
  • DE: +49 (0) 69 9579 7960
  • China: +86 400 0550 036
  • Japan: 03 4455 7823
  • AU: +61 3 8331 4800
  • Egypt: +20 8000000826
  • UAE: +971 8000320817
  • Kuwait: +965 22069086
  • Saudi Arabia: +966 8008500030
  • Middle East & Africa: +971 42428633
• Email: support@eufylife.com
• Address: Anker Innovations Limited, Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
• Social Media: @EufyOfficial (Facebook, Instagram, Twitter)

Notices and Compliance

?Safety: This equipment is not suitable for use where children are present and is not intended for use by children. Do not use the product in any way other than described to avoid personal injury or property damage. Users must comply with local laws and regulations. Ensure an appropriate disconnect device is provided and an all-pole mains switch is incorporated in the electrical installation. The luminaire requires supply conductors long enough to extend 150mm into the outlet box. Caution: risk of electric shock. Installation must be performed by a person familiar with the product and its hazards. Minimum 90°C supply conductors are required.

?FCC Statement (United States): This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: no harmful interference caused, and acceptance of any interference received. Modifications not expressly approved may void user authority. Tested to comply with Class B digital device limits for reasonable protection against harmful interference in residential installations. Generates RF energy; improper installation may cause interference. If interference occurs, try reorienting the antenna, increasing separation, connecting to a different circuit, or consulting a technician. FCC Radio Frequency Exposure Statement: Device meets general RF exposure requirements with a minimum separation distance of 20cm. Notice: Use shielded cables for all connections to other computing devices.

?IC Statement (Canada): Complies with Industry Canada licence-exempt RSS standards. Subject to two conditions: no interference caused, and acceptance of any interference. Complies with Canadian ICES-003. IC RF Statement: Maintain a distance of 20cm from the body for RF exposure compliance.

?Notice (Europe and United Kingdom): Complies with radio interference requirements of the European Community (Directive 2014/53/EU) and UK Radio Equipment Regulations 2017. Suitable temperature range: -20°C to 50°C; recommended 5°C-25°C. RF exposure information: Maximum Permissible Exposure (MPE) calculated for 20cm separation. Wi-Fi: 2.4GHz, 2412-2472MHz, EIRP 19.83dBm. Importers listed for EU (Anker Innovations Deutschland GmbH) and UK (Anker Technology (UK) Limited).

?Notice (Australia): Temperature guidelines: -20°C to 50°C, recommended 5°C-25°C. Product designed with high-quality, recyclable materials. Disposal instructions: Do not discard as household waste; deliver to appropriate collection facility for recycling.