Goblin Helicopters
Installation Guide for GOBLIN models including: H2242-K, H1893-S, H2193-S, HPS3 Rotor Tail, HPS3, Rotor Tail, Tail
3 Blades Tail D8 Conversion Kit | Goblin Helicopters
17 дек. 2024 г. — ... Genesis Sport into a 3-blade tail rotor. Please read this user manual carefully, it contains instructions for the correct assembly of the KIT. Please refer ...
File Info : application/pdf, 2 Pages, 2.38MB
DocumentDocumentHPS3 ROTOR TAIL [ H2242-K ] Bag 1 This KIT is designed to convert the 2-blade tail rotor of the IL Pro, IL Raw and Genesis Sport into a 3-blade tail rotor. Please read this user manual carefully, it contains instructions for the correct assembly of the KIT. Please refer to the website www.goblin-helicopter.com for updates and other important information. Thanks You. NOTE: It is a normal for the tail to feel a bit tight after initial assembly as the tail spindle preload is usually high when the helicopter is brand new. The preload will loosen up after 2-5 flights allowing the system to become smooth. Tail Blade Grip Assembly (H1893-S) eg: MULTI PURPOSE GREASE [HA096] Spacer 7.5x 10x0.5mm [H0349] (H0330-S) C Shim [HC449] Use in case tail grip are too play Tail Hub HPS3 (H2193-S) Bearing 5x 10x4mm (HC411-S) Button Head Cap Screw M3x6mm (HC094-S) Smaller ID Thrust Bearing 5x 10x4mm (HC435-S) Larger ID Socket Head Cap Screws M2x6mm (HC004-S) Tail Shaft HPS3 (H2194-S) Bushing (H0435-S) Washer 2.2x 5x0.3 (HC170-S) Bushing 2x 3x3 [H0076] (H0056-S) Tail Pitch Slider Link (H0056-S) Set Screw M4x6mm (HC153-S) eg: MULTI PURPOSE GREASE [HA096] Tail Pitch Slider Assembly (H2195-S) Page 01 HPS3 ROTOR TAIL [ H2242-K ] Bag 2 Tail Pulley Assembly (H2083-25-S) SPARE PARTS Pin M2 [H0435-S] Tail Blade Grip [H1893-S] - 3 x Pin M2. - 3 x Spacer 2x 3x3mm. - 3 x Tail Pitch Slider Link. - 6 x Head Cap Screws M2x6mm. Tail Pulley Z25 [H2083-25-S] Set Screw M4x6mm (HC153-S) NOTE: The set screw must align with the hole in the tail shaft Nylon Nut M3 (HC206-S) Washer 3.1x 5.75x0.5 (HC714-S) Use in case tail blades are too loose Socket Head Screw RECOMMENDATIONS Shoulder M3x18mm (HC079-S) * These parts should be used only with models SAB. * Please follow all the instructions shouwn in the Goblin main manual. In this manual please read Chapter 2, Important notes. * Use Loctite on all threads. * Prior to use, lubricate all movements with sprat lubricant. * Possible to use with the follow Tail blades: SAB blades for 3 blades tail rotor 110 mm SAB blades for 3 blades tail rotor 115 mm - 1 x Tail Pulley Z25. - 2 x Tail Pulley Z25 WS. - 6 x Button Cap Screws M2x4mm. - 1 x Set Screw M4x6mm. Tail Shaft HPS3 [H2194-S] - 1 x Tail Shaft HPS3. - 2 x Set Screws M4x6mm. - 2 x Tail Blade Grip. - 2 x Washer 7,5x 10x0,5. - 2 x Button Cap Screws M4x6mm. - 4 x Ball Bearing 5x 10x4. - 2 x Thrust Bearing 5x 10x4. Tail Hub HPS3 [H2193-S] - 1 x Tail Hub. - 1 x Set Screw M4x6mm. - 3 x Button Cap Screws M4x6mm. Tail Pitch Slider [H2195-S] - 1 x Tail Pitch Slider Assembled. Page 02