User Manual for BITMAIN models including: BITMAIN, Antminer, APW5-12-2600, PSU Series
1. Overview. The APW5-‐12-‐2600 series AC-‐DC PSU combines high efficiency and good dynamic performance into a power dense package. It also features overload, overheat, overcurrent and low...
BITMAIN APW5--12--2600 PSU Series User Guide 1 Content 1. Overview . ................................................................................................................. 3 2. Features ................................................................................................................... 3 3. Specifications ........................................................................................................... 4 4. Order Information & Wire Type . .............................................................................. 6 5. Trouble Shooting & FAQ . .......................................................................................... 7 6. Precautions for Use . ................................................................................................. 7 2 1. Overview The APW5--12--2600 series AC--DC PSU combines high efficiency and good dynamic performance into a power dense package. It also features overload, overheat, overcurrent and low voltage protection, making it well suited to 12V, 2600W power devices. Please note: 1. This PSU cannot be used in countries where the mains power voltage is lower than 100V because the PSU will not start below this voltage 2. Features l 110V/120V±20% voltage input range l High efficiency, up to 94.6% l Short circuit, overload and overheat protection l Extreme power density l An active power factor corrector function, PF>0.99(full load) l Fan speed changes with temperature l User can change output lines and fine--tune output voltage l 12 Month Warranty 3 3. Specifications Output Input Protection Environment Conditions Structure Cooling DC Voltage 12.25V Rated Current (220V input) 216A Rated Power (220V input) 2600W Rated Current (110V input) 108A Rated Power (110V input) 1300W Ripple & Noise <1% Voltage Regulation <2% Source Regulation <1% Load Regulation <1% Setup, Rise Time <5S Power Off Protection Trip Time >10mS Interface Type 7 pairs of 6 pin PCI--E connectors. 380mm length for each PCI--E cable. Voltage Range 90--265V AC Current Range 10.5--16.5A Starting Voltage 100--240V AC Frequency Range 47--63Hz Power Factor >0.95(full load) Leakage Current <1.5mA (220V 50Hz) Low--voltage Input 90--100V AC Output Short Circuit Yes Output Overcurrent (220V 216--255A input) Output Overcurrent (110V 108--135A input) Overheat Protection Yes Operating Temperature --20 -- 60 Operating Humidity 20%--90% RH (non--condensing) Dimensions 266mm*125mm*86mm Weight 2.5Kg Fan Forced--air cooling Fan speed When the temperature of the heat sink is higher than 80 , the fan runs at full speed. 4 Max Load vs. Ambient Temperature Graph (220V input) CurrentA 220 216 210 Input220V 216 216 216 200 200 190 180 170 160 --20 0 20 50 55 60 Efficiency vs Load (220V input) EFF Efficiency 96.0% 94.0% 92.0% 90.0% 88.0% 86.0% 84.0% 10 60 110 160 currentA Temp efficiency load current 210 A 5 4. Order Information & Wire Type 4.1 Order Information 4.2 Wire Types 7 pairs of 6 pin PCI--E connectors. 380mm length for each PCI--E 6 5. Trouble Shooting & FAQ # Issue Reason Troubleshooting 1 Fan won't AC Input is 1. Make sure the AC input wire has a good connection run, and no abnormal and the plugs are connected firmly 12V output 2. Make sure the mains power is working well and its voltage is above 100V. 2 The fan is 1. Voltage in 1. Please check whether the voltage is above 100V running, but your power with multimeter to make sure the PSU can switch on there is no system is lower correctly. 12V output. than required 2. Check whether there is a short circuit output or 2. PSU is in overload that is causing the PSU to enter a locked protection status. After removing the problem, the PSU should mode power up. 3 After a few PSU is in over-- 1Check whether the fan is working minutes, the heat protection 2Check whether the fan's vent is being blocked PSU 3Check whether there is a dust buildup inside the repeatedly PSU due to prolonged use. Do NOT remove the PSU's stops and cover unless trained to do so. starts and 4Check that the power and ambient temperatures keeps cycling. follow the Load/Temperature graph 4 Output is Fan is broken 1. Check that the fan is clear of blockages or buildup normal but 2. Fan is broken and needs to be replaced. the fan is not working. 5 The PSU The PSU is in Check whether the load current has exceeded the suddenly has over--current built--in overcurrent protection limit. The protection no output protection. automatically triggers when the load current exceeds and can't be the limit to protect against damage to the PSU and started again. the server. 6. Precautions for Use 1. Before using the PSU, please ensure that the voltage and power outputs are compatible with your equipment. 2. Please ensure that the PSU appears to be in good shape and has not suffered damage in transit. If the exterior of the PSU appears damaged, do not use it. 3. Make sure that the metal cover for the PSU with on/off switch is properly grounded. Improper grounding is dangerous. 7 4. The PSU must be installed in such a way that it receives good, unobstructed airflow. Under no circumstances should the PSU be installed in an enclosed place. 5. When installing the PSU, please double check that the output polarities are the correct way round, and that the screws are fastened securely in place. 6. Do not attempt maintenance on any wiring while the PSU is powered up from the mains. 7. Running the PSU at <80% load or below can greatly prolong the life of the PSU. Usually, for every 10ºC above the rated amount, the life of the PSU is cut in half. 8 9Word Mac OS X 10.10.5 Quartz PDFContext