IP PAR725 QUAD
Outdoor IP65 7x25W QUAD LED Projector
Brand: Algam Lighting
Safety Instructions
The following symbols are internationally accepted symbols to warn of potential hazards related to the use of electrical equipment. If any of these symbols are present on your device, please read the following instructions:
- ATTENTION! Before using your equipment, we recommend that you read all the instructions in this manual.
- ATTENTION! This device produces an intense and powerful light. Risk to the eyes. Do not look directly into the beam.
- DANGER! Hazardous voltage, risk of electric shock. Do not open the product.
- ATTENTION! Risk of burns. The exterior of the unit can become very hot. Do not touch within 10 minutes of use.
- ATTENTION! Fire hazard. Keep all combustible and flammable materials away from the unit during operation.
- DANGER! Safety hazard. This appliance presents a significant risk of injury. Follow the safety instructions.
[Distance Symbol] 0.5m Place the unit at least 50cm away from flammable materials and walls.
PROTECTION CLASS IP65 The equipment is designed and tested for IP65 protection in accordance with EN 60529. This degree of protection corresponds to resistance to dust and water (jets of water) allowing the product to be used outdoors. However, it does not protect against immersion.
For ports with protective caps: handle the protective caps on the connectors with care, as they ensure that the product is dust- and water-tight. When the port is not in use, check that the connectors are free of dust and moisture, and close the protective caps carefully.
The IP65 rating does not guarantee the device's resistance to outdoor conditions (UV, heat, temperature variations...).
Installation
- Unpack and check carefully for transport damage before using the product. Never put a damaged product into operation.
- This product must be installed with strong hooks of adequate size for the weight carried. The product must be screwed to the hooks and tightened properly to prevent it from falling due to vibrations. Also check that the structure (or hanging point) can support at least 10X the weight of the hanging unit. The device must be installed by a qualified person and must be placed out of reach of the public. It is necessary to use a secondary hanging system (safety sling) approved for the weight of the device.
- Do not place the unit, speakers or any other object on top of the power cord and make sure it is not pinched.
- For proper protection against electric shock, the unit must be connected to earth (ground). The electrical supply circuit must be equipped with a fuse or circuit breaker and a differential protection device.
- Power Disconnection Notice: To disconnect the device from the power source, the power plug must be removed from the power outlet. For this reason, the device must be placed in a position that allows constant, unobstructed access to the power outlet. This way, in case of an emergency, you can disconnect the power plug immediately.
- The unit should only be installed in a well ventilated area. Make sure that no ventilation slots are blocked. To ensure adequate ventilation, leave at least 20 cm of free air space around the sides and top of the unit.
- To reduce the risk of strangulation the flexible wiring connected to this luminaire shall be effectively fixed to the wall if the wiring is within arm's reach.
Usage
- This appliance must not be used by persons (including children) with limited physical, physiological or mental capabilities or lack of experience and/or knowledge, unless they are supervised by a person responsible for their safety or are instructed by that person in the operation of the appliance.
- Never leave this equipment unattended.
- If you experience any problems with the unit, stop using it immediately. Do not attempt to repair it yourself. Contact your dealer or an authorized service center. There are no user replaceable parts.
- NEVER use the unit under the following conditions:
- In areas subject to vibration or bumps,
- In places where the ambient temperature is above 45°C or below 2° C.
- In areas exposed to excessive dryness or humidity (ideal conditions: between 35% and 80%).
- Never use the unit near flames, flammable or explosive materials or hot surfaces. Doing so may cause a fire.
- The exterior of the unit can become very hot. It is important to avoid contact with the unit during operation and for at least 10 minutes after use.
- It is important to use the supplied power cable (grounded cable).
- Before turning on the power, make sure that the voltage and frequency of the power supply match the power requirements of the unit, as described in this manual.
- Never cut or tamper with the power cord or plug. If a power cord is provided with a ground wire, it is required for safe operation! Risk of fatal electric shock!
- Always hold the power cord by the plug. Do not pull on the cord itself and never touch the power cord with wet hands as this may cause a short circuit or electric shock.
- Do not connect this device to a dimmer pack.
- You must ensure that the power cord never gets wet during operation. Before a thunderstorm and/or a lightning storm, unplug the unit from the mains.
- Under no circumstances should you open the housing of the device. If you do, your safety will not be assured. There are no operational components inside, only dangerous voltages that can give you a fatal shock!
- WARNING: This device emits bright flashes of light that may trigger epileptic seizures in photosensitive individuals.
Maintenance / Service
- Never attempt to disassemble, repair or modify the unit yourself. Otherwise, the warranty becomes void. Repairs by unqualified persons may result in damage or malfunction. Please contact the nearest authorized service center. The light source contained in this fixture should only be replaced by the manufacturer or its service agent or a person of equivalent qualification.
- Screens, lenses or UV filters should be replaced if they are visibly damaged to an extent that compromises their effectiveness, such as by deep cracks or scratches.
- The lamp should be replaced if it has been damaged or deformed by heat.
- Disconnect the unit from the mains before servicing.
- If the cable or flexible outer cord of this fixture is damaged, it must be replaced with a special cable or cord from the manufacturer or its service agent only.
- Never immerse the unit in water or any other liquid. Wipe only with a slightly damp cloth.
- CAUTION: To reduce the risk of fire replace fuse with same type and rating.
Product Installation
Power Supply
Please use the attached power, note that power voltage and frequency are the same as the marked voltage and frequency of device when connecting power. Every device's power should be connected separately, so that device can be controlled individually.
| CABLE (EU) | CABLE (US) | PIN | INTERNATIONAL |
|---|---|---|---|
| Brown | Black | Live | L |
| Light Blue | White | Neutral | N |
| Yellow/Green | Yellow/Green | Earth |
DMX Connection
Connection between lights and DMX must use the shied cable of diameter more than 0.5mm. Please use the attached 3 pin XL plug/socket to connect the DMX output/input interface. The connection between socket and cable as below (note the plug/socket's 3 pin number and position).
DMX-OUTPUT (XLR mounting-sockets, rear view):
- Pin 1: Shield
- Pin 2: Shield (-)
- Pin 3: Shield (+)
DMX-INPUT (XLR mounting-plugs, rear view):
- Pin 2
- Pin 3
When using standard DMX512 control signal, the last device's output interface must be connected to a DMX plug. This plug is putting a 120 ohm resistance between "canon" plug's 2 pin and 3 pin. Sticking this plug into the last device's signal output interface, it will avoid the interference during the process of signal transmission.
Rigging
Attention! The installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and /or damage to property. Overhead rigging required extensive experience! Working load limits should be respected, Certified installation materials should be used, the installed device should be inspected regularly for safety.
Operation Instructions
The unit features the following controls:
- 1. Digital display: For setting model.
- 2. Connector/cable POWER IN: Power input socket.
- 3. DMX IN: 3PIN male XLR interface for DMX communication.
- 4. Control buttons: Navigating menus and functions (MENU, UP, DOWN, ENTER).
- 5. Connector/cable POWER OUT: Power output connect with next light.
- 6. DMX OUT: 3PIN female XLR interface for DMX communication.
[Diagram description: A circular diagram shows the back panel of the IP PAR725 QUAD with numbered ports and controls. 1 is the digital display, 2 is the POWER IN socket, 3 is DMX IN (male XLR), 4 are the control buttons (MENU, UP, DOWN, ENTER) located near the display, 5 is the POWER OUT socket, and 6 is DMX OUT (female XLR). Safety warnings and IP65 rating are also visible.]
Menu Operating Instructions
Use the control buttons (MENU, UP, DOWN, ENTER) to navigate and adjust settings.
- [MENU button]: To go forward in selected functions or go back to the last layer menu.
- [UP arrow button]: To go forward in selected functions or increase parameters.
- [DOWN arrow button]: To go backward in selected functions or reduce parameters.
- [ENTER button]: To go into the next layer menu or validate commands.
Saving Operations: Press ENTER to save any operation. The unit will return to the last menu in 10 seconds.
Restore Factory Settings: Hold the MENU button and connect the power cable.
| DISPLAY SHOW | NUMERICAL VALUE | FUNCTION AND DESCRIPTION |
|---|---|---|
| d001 | 001-512 | DMX512 address setting – 4 channel mode |
| A001 | 001-512 | DMX512 address setting - 9 channel mode |
| r255 | 000-255 | Red dimming, from dark to bright |
| G255 | 000-255 | Green dimming, from dark to bright |
| b255 | 000-255 | Blue dimming, from dark to bright |
| u255 | 000-255 | White dimming, from dark to bright |
| FH99 | 01-99 | Strobe, speed from slow to fast |
| CL01 | 01-08 | 8 common color output. |
| CC99 | 01-99 | Colorful jump, from slow to fast. |
| dE99 | 01-99 | Colorful gradient, from slow to fast. |
| CP99 | 01-99 | Colorful pulse change, from slow to fast. |
| SU01 | 01-09 | Colorful sound control choice |
DMX Protocol
4 Channels
| CHANNEL | FUNCTION | DESCRIPTION |
|---|---|---|
| CH1 | R dimming | Red dimming, from dark to bright |
| CH2 | G dimming | Green dimming, from dark to bright |
| CH3 | B dimming | Blue dimming, from dark to bright |
| CH4 | W dimming | White dimming, from dark to bright |
9 Channels
| CHANNEL | FUNCTION | DESCRIPTION |
|---|---|---|
| CH1 | Master Dimmer | RGBWAUV master dimmer, from dark to bright |
| CH2 | R dimming | Red dimming, from dark to bright |
| CH3 | G dimming | Green dimming, from dark to bright |
| CH4 | B dimming | Blue dimming, from dark to bright |
| CH5 | W dimming | White dimming, from dark to bright |
| CH6 | Master strobe | 000-004 Close the strobe 005-255 Strobe, speed from slow to fast |
| CH7 | CTO | Color temperature: 3200-8000 warm |
| CH8 | Function selection | 0 - 50 CH1-8 valid 51 - 100 8 common color output 101 - 150 Colorful jump 151 - 200 Colorful gradient 201 - 250 Colorful pulse change 251 - 255 Sound mode |
| CH9 | Function speed | Color selection / speed addition / sound control selection |
Specifications
| Product size | 260 x 160 x 285mm |
| Weight | 2.75kg |
| Power consumption | 180W |
| Input voltage | 100-240V~ 50/60Hz |
| Light Source | 7 x 25W RGBWA LED |
| DMX Channel | 4/9 CH |
| Dimmer | 0%-100% linear dimming |
| IP Rating | IP65 |
| Control mode | DMX512, sound control, automatic, master/slave |
Disposal and Compliance
[WEEE Symbol] This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) in its currently valid version. Do not dispose with your normal household waste.
Dispose of this device through an approved waste disposal arm or through your local waste facility. When discarding the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility.
[CE Mark] This Algam Lighting product is compliant to all required UE certifications and conformed to following standard and UE directives:
- LVD Directive 2014/35/EU
- EMC Directive 2014/30/EU
- RoHS 2 Directive 2011/65/EU
The UE DECLARATION OF CONFORMITY is available, if you need it, please just ask for it at: contact@algam.net
