Panasonic Strada CN-RA05D/CN-RA05WD Installation Manual

Important Safety Information

Warning: Read and understand all instructions before installation. Failure to follow these instructions or using unspecified parts may lead to accidents or damage, for which Panasonic is not liable. Such installations may also void the product warranty.

For Retailers: Ensure this manual is provided to the customer after installation.

For Customers: Installation and wiring require professional knowledge and experience. For safety, please entrust the work to your retailer.

Connection Terminals

This section identifies the connection terminals for reference during installation. Refer to "Wiring Instructions" (P.7-9) for detailed wiring information.

• ETC 2.0 Vehicle-Mounted Device Terminal (ETC 2.0): For connecting a separately sold ETC 2.0 vehicle-mounted device. Remove the seal if not in use.
• iPod/USB Connection Terminal (iPod): Use a separately sold cable to connect an iPod or commercial USB memory. Remove the seal if not in use.
• Navigation Unit (Rear): Contains terminals for various connections.
• GPS Antenna Terminal (GPS ANT): For connecting the GPS antenna.
• Cooling Fan: Ensure this area is not obstructed.
• Drive Recorder Connection Terminal: For connecting a separately sold drive recorder.
• Power Connector (POWER FUSE 15A): Includes a built-in 15A fuse.
• Vehicle AV Interface Connection Terminal (AV I/F): For connecting to the vehicle's AV interface.
• Digital TV Antenna Connection Terminal (DIGITAL TUNER ANT IN): For connecting the digital TV antenna.
• Radio Antenna Input Terminal (FM/AM ANT): For connecting the radio antenna.

Table of Contents (Summary)

The manual is organized into sections covering safety precautions, installation steps, wiring instructions, antenna placement, unit installation, and integration with other devices.

Safety Precautions

General Warnings:

• Risk of Death or Serious Injury: Do not install or wire in locations that obstruct vision or endanger passengers. Do not install in areas prohibited by the vehicle manufacturer, as this may interfere with safety systems like airbags.
• Risk of Injury or Property Damage: Use only supplied or specified parts. Ensure secure installation to prevent detachment during driving. Keep the installation area clean and dry. Regularly check the installation status. Ensure wiring does not interfere with moving parts or hot surfaces. Do not block the unit's ventilation holes.
• Prohibited Actions: Do not modify or disassemble the unit. Do not cut the insulation of cords to power other devices. Do not modify or connect the ground cord to other devices.
• Handling Small Parts: Keep small parts away from children to prevent accidental ingestion.
• Cord Handling: Avoid damaging cords by pinching, pulling, bending, or exposing them to heat or metal parts. Secure cords with clamps or tape.

Installation Procedure

1. Disconnect the Battery: Disconnect the battery terminal before starting work.
2. Install Other Devices: Install supplied antennas, microphones, and separately sold accessories. Temporarily fit them to confirm placement.
3. Route Cords/Cables: Route all cords and cables, ensuring they do not interfere with driving or come into contact with hot surfaces or sharp metal edges. Use cord clamps or tape for securing. Ensure power connector is connected last.
4. Install Navigation Unit: Mount the navigation unit in the vehicle. Ensure correct installation kits are used if required for your vehicle model.
5. Reconnect the Battery: Reconnect the battery terminal securely.
6. Check Installation and Wiring: Verify all connections and ensure all vehicle electrical systems are functioning correctly.

Wiring Instructions

Detailed diagrams illustrate how to connect various components, including power, speakers, antennas, and interface cables. Specific instructions are provided for:

• Crimping Connectors: Ensure connectors are fully inserted.
• Removing Lock-Type Cords: Push in the direction of the arrow to remove.
• Antenna Connections: Connect GPS, digital TV, and radio antennas correctly. Keep antenna cords separate and avoid bundling them together to prevent signal degradation.
• Power and Ground Connections: Connect the power connector and ground cord securely to appropriate points.
• Other Connections: Instructions for connecting speaker cords, steering wheel remote control codes, reverse signal, speed pulse, and camera input are provided.

Antenna Installation

General Guidelines:

• Consult your vehicle manufacturer or dealer regarding specific installation requirements and vehicle features (e.g., airbags, heat-reflective glass).
• Adhere to the installation range specified by regulations for digital TV antennas.
• Install the GPS antenna indoors, on the dashboard near the windshield, away from other electronic devices to ensure optimal reception.
• Clean the installation surface thoroughly before applying antennas. Use a hairdryer to warm the surface in cold weather.
• Do not bend or force antennas.
• Do not touch the adhesive surface or power feeding section.

Digital TV Antenna Placement:

• Install the power feeding section and cords within the specified range from the edge of the windshield (approx. 25 mm).
• Ensure antennas are placed in the correct orientation and location for optimal performance.
• Avoid placing antennas over inspection stickers or in overlapping positions.

GPS Antenna Placement:

• Install on the windshield near the dashboard.
• Keep at least 15 cm away from other antennas and devices.
• Secure the cord with cord clamps.

Navigation Unit Installation

Mounting Bracket: Use the supplied mounting bracket and screws. Ensure correct screw lengths are used.

Audio Space Installation:

• Confirm the dimensions of the unit (180 mm width x 100 mm height for 2DIN).
• Ensure the installation angle is within 40° of horizontal. Incorrect angles may affect gyro sensor performance and vehicle position display.
• Do not force the unit into the audio space, as this can damage wiring.
• If the mounting bracket interferes with the dashboard, it may need to be trimmed.
• Avoid pressing hard on the front of the unit or its controls, as this can cause damage.

Connecting Other Devices

This section details how to connect various accessories:

• ETC 2.0 Vehicle-Mounted Device: Use the dedicated connection cord.
• Rearview Camera: Connect the camera using the provided cables.
• iPod/USB Memory: Use the specific connection cable (CA-LUB200D). Ensure iPod is powered on. Secure devices to prevent movement. Avoid high temperatures and direct sunlight.
• Drive Recorder: Connect using the dedicated navigation connection cord.
• Rear Seat Monitor: Requires the separately sold Vehicle AV Interface Cord (CA-LAV200D).
• Video Camera: Requires the separately sold Vehicle AV Interface Cord (CA-LAV200D). Use the appropriate adapter cable for the video camera's connection type.

Installation and Wiring Check

Power On: Start the vehicle's engine (ACC ON) and check if the unit powers on.

Confirm Safety Screen: Review the safety information displayed and select confirmation.

Check GPS Reception: In a location with good visibility, check if the GPS reception indicator turns yellow. If not, verify GPS signal status (P.23). Ensure correct vehicle position is displayed.

Check Two-Top Menu: Press the MENU button to display the two-top menu.

Verify Vehicle Signal Information: Navigate through the menus to check battery voltage, parking brake status, reverse signal, illumination signal, and speed pulse. Ensure these signals are correctly detected.

Check Sensor Learning Values: Reset sensor learning values if necessary and re-check after driving. This is important for accurate vehicle position and performance.

Check Extended Unit Information: Verify that connected units (e.g., USB, iPod, ETC 2.0, Drive Recorder) are recognized by the system.

Set Vehicle Type: Select the appropriate vehicle type from the settings menu for optimal performance.

Steering Wheel Switch Settings

If your vehicle is equipped with steering wheel controls, you can assign functions to them:

1. Navigate to Information > Settings > System Settings > Steering Switch.
2. Select the desired function for each steering wheel switch.
3. Press and hold the switch for 1 second to assign the function.
4. Repeat for all switches. Ensure all switches have a function assigned for proper operation.

GPS Information Check

Navigate to Information > Settings > Information > GPS Information to view details such as latitude, longitude, number of satellites acquired, date, and time.

Trademarks and Other Information

This section lists trademarks related to ETC, VICS, Apple products (iPhone, iPod), and other company names and product names.

Parts Included

A list of included parts is provided, including the navigation unit, SDHC memory card, antennas, cables, connectors, cleaner, and instruction manual kit.

Note: The unit does not come with a B-CAS card, but terrestrial digital broadcasting can be viewed without one.

Manufacturer Information

Panasonic Corporation, Automotive & Industrial Systems Company, Yokohama, Japan.