Netum NFTUM Barcode Scanner

Illumination Settings

• 0200020 OFF: Illumination LEDs are OFF all the time.
• 0200010 Always ON: Illumination LEDs keep ON after the engine is powered on.
• Normal: Illumination LEDs are turned on during image capture.

Aiming Pattern

When scanning/capturing an image, the scanner projects an aiming pattern which allows for positioning the target barcode within its field of view, thus making decoding easier.

• Normal: The engine projects an aiming pattern only during barcode scanning.
• Always ON: Aiming pattern is constantly ON after the engine is powered on.
• OFF: Aiming pattern is OFF all the time.

Beep Settings

• 0203010 ** Beep On: Enables the scanner to beep to indicate a successful scan.
• 0203000 Beep Off: Disables the scanner from beeping to indicate successful scans.

Beep Volume

• 0203030 ** Loud
• 0203031 Medium
• 0203032 Low

LED ON/OFF

• 0206011 ** LED ON
• 0206010 LED OFF

Video Reverse Feature

The Video Reverse feature applies only to 2D barcodes. The examples of regular and inverse barcodes are shown below.

• 0001021 Video Reverse ON: Reads both regular and inverse barcodes.
• 0001011 ** Video Reverse OFF: Reads regular barcodes only.

Scanner shows a slight decrease in scanning speed when Video Reverse is ON.

Quick Setup Guide

This is a plug-and-play model if you use a US keyboard. If you use another type of keyboard, you need to set the keyboard language (please refer to USB Country Keyboard Types) before using the scanner. For other configurations, please refer to the relevant programming barcodes below.

Barcode Programming

Netum barcode scanners are factory programmed for the most common terminal and communication settings. If you need to change these settings, programming is accomplished by scanning the barcodes in this guide. An asterisk (**) next to an option indicates the default setting.

Important Notes:

All configurations need to go through the following steps except Factory Defaults: Scan "Enter Setup" ➔ "Programming Barcode" ➔ "Exit Setup".

• 0006010 Enter Setup
• 0006000 ** Exit Setup

If the scanner has exited the setup mode, only some special programming barcodes, such as the Enter Setup barcode and Factory Defaults barcode, can be read.

Factory Defaults

Configures the scanner to revert all settings to factory defaults.

• 0001000 Factory Defaults

Custom Defaults

Scanning the Save as Custom Defaults barcode can save the current settings as custom defaults. Once custom default settings are stored, they can be recovered at any time by scanning the Restore All Custom Defaults barcode. Custom defaults are stored in non-volatile memory. Restoring the scanner to factory defaults will not remove the custom defaults from the scanner.

• 0001150 Save as Custom Defaults
• 0001160 Restore All Custom Defaults

USB Interface (Optional)

USB HID-KBW

By default, the scanner is in HID mode as a Keyboard device. It works on a Plug and Play basis and no driver is required.

• 1100020 ** USB HID-KBW

USB Country Keyboard Types

If your interface is USB Keyboard, your keyboard layout default is a US keyboard. To change this layout, scan the appropriate Keyboard Country barcode below.

• 1103001 ** U.S.
• 1103002 Japan
• 1103003 Denmark
• 1103004 Finland
• 1103005 France
• 1103006 Turkey_F
• 1103007 Italy
• 1103008 Norway
• 1103218 Portugal
• 1103222 Spain
• 1103223 Sweden
• 1103202 Belgium
• 1103227 UK
• 1103209 Austria, Germany

USB COM Port Emulation

If you connect the scanner to the Host via a USB connection, the USB COM Port Emulation feature allows the host to receive data in the way as a serial port does. A driver is required for this feature.

• 1100060 USB COM Port Emulation

USB HID-POS

The USB HID-POS interface is recommended for new application programs. It can send up to 56 characters in a single USB report and appears more efficient than keyboard emulation.

Note: USB HID-POS does not require a custom driver. However, a HID interface on Windows 98 does. All HID interfaces employ standard drivers provided by the operating system. Use defaults when installing the driver.

• 1100080 USB HID-POS

Scan Mode

Trigger Mode (Default)

Scanning this barcode will enable the scanner to enter manual trigger mode.

• 0302000 ** Trigger Mode

Auto Sense Mode

Scanning this barcode will enable the scanner to enter auto sense mode.

• 0302010 Sense Mode

Continuous Mode

This mode enables the engine to scan/capture, decode, and transmit over and over again.

• 0302020 Continuous Mode

Illumination Options

A couple of illumination options are provided to improve the lighting conditions during every image capture:

• 0200000 ** Normal

FAQ

Problem: Some barcodes cannot be read.

Solution:

1. Dirty or unclear barcodes might not be read.
2. The possible reason is that the setting for some barcode types is not commonly used and is off by default. You need to activate a specific barcode type to get it to work. Please contact the supplier from whom you purchased it, or go to the official website www.gzxlscan.com to download the complete manual and refer to the "Symbologies" section.
3. Clean the scanner window.

Problem: Barcodes can be read, but cannot be displayed.

Solution: Verify that the serial port parameters (such as baud rate, data bit, and stop bit) settings match the host requirements.

Problem: Carriage Return/Line Feed settings.

Solution: Please go to the official website www.gzxlscan.com to download the complete manual and refer to the part about "Terminating Character Suffix".

Question: Are there any barcodes for applying or removing a suffix?

Yes, you may go to our official website www.gzxlscan.com to download the complete manual and refer to the "prefix and suffix" section, or contact customer service for help.

Question: How to solve the messy code problem encountered while using other foreign languages?

The default language is English. Please refer to "USB Country Keyboard Types" to change the language according to your needs.

Support

If you have any inquiries, please do not hesitate to contact us.

Contact Information

• Tel: +0086 20-6626-0708
• Email: service@gzxlscan.com
• Skype: service@gzxlscan.com
• Web: www.gzxlscan.com
• Address: Unit 137, The Pacific Industry Park, Xintang Town, Zengcheng District, Guangzhou, China/511340
• Made in: China

Packing List

• Quick Start Setup Guide x 1 pc
• Barcode scanner x 1 pc

Quick Setup Guide V4.1