Smartbright 'Tri-Colour' Batten BN125
Mounting Instruction
Version: V1.0
Certifications: AS/NZS 60598, IP20, Indoor Use (ta25°C), Grounded
Product Specifications
Product Type | Dimension (mm) | CCT (K) | Lumen Output (lm) | Power (W) | Voltage | Frequency | Weight (kg) |
---|---|---|---|---|---|---|---|
BN125C LED SWT/SCCT L600 PSU AU | 600x65x65 | 4000K/5000K/6500K | 1380/2000 | 12W/20W | 220-240V~ | 50/60Hz | 0.85 |
BN125C LED SWT/SCCT L1200 PSU AU | 1200x65x65 | 4000K/5000K/6500K | 2300/4000 | 20W/40W | 220-240V~ | 50/60Hz | 1.45 |
1. Luminaire Dimension
Diagram showing the luminaire dimensions. The overall length is indicated as L=600/1200 mm, the width is 65 mm, and the height is 55 mm.
Dimensions: Length 600/1200 mm, Width 65 mm, Height 55 mm.
2. Supply Cord
Diagram illustrating the supply cord connection. It shows a 60245 IEC57 3x1.0~1.5mm² cable with three wires: Brown (connected to L), Yellow/Green (connected to GND), and Blue (connected to N).
Cable type: 60245 IEC57 3x1.0~1.5mm². Wire connections: Brown (L), Yellow/Green (GND), Blue (N).
3. Surface Mounting
Diagrams for surface mounting. For the L600 model (A), mounting distances are shown: A=573 mm, B=121 mm, C=40 mm, with four mounting holes indicated. For the L1200 model (B), mounting distances are A=972 mm, B=40 mm, with four mounting holes indicated.
L600 Mounting Distances: A=573 mm, B=121 mm, C=40 mm (4 mounting points). L1200 Mounting Distances: A=972 mm, B=40 mm (4 mounting points).
4. Open the Luminaire and Take Out the Accessories Bag
Illustration of opening the luminaire and accessing the accessories bag. It shows the luminaire cover being removed, revealing the internal components and an accessories bag labeled 'included (4X)', indicating four items are included.
Action: Open luminaire, retrieve accessories bag (contains 4 items).
5. Power Supply Connection
Diagram showing the power supply connection. Wires are connected to terminals within the luminaire. The diagram depicts the internal wiring layout.
Connect power supply wires to the designated terminals inside the luminaire.
6. CCT and Power Regulating Switch
Illustration of the CCT and Power regulating switches. The CCT switch allows selection between 4000K, 5000K, and 6500K. The Power switch has two settings: 'H' for half power and 'F' for full power.
CCT Switch: Select 4000K, 5000K, or 6500K. Power Switch: Select 'H' (Half Power) or 'F' (Full Power).
7. Close the Luminaire
Diagram showing the final step of closing the luminaire.
Action: Securely close the luminaire.
Important Safety Information and Precautions
- For indoor use only.
- Do not switch on before complete installation.
- The luminaire must be installed by a licensed electrician and wired in accordance with Australian wiring rules.
- The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire shall be destroyed.
- The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
- The luminaire is complied with AS/NZS 60598.
- Luminaire must not be used or stored in corrosive environments where hazardous materials such as Sulphur, Chlorine, phthalates, etc., are present.
Environmental Disposal Information
This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
Recycle responsibly. Do not dispose of with household waste.