Monster Open Ear AC600 Bluetooth Headphones
Quick Start Guide
Product Overview
Contents:
- Earphones x 2 (left & right)
- Charging Case
- USB-C Charging Cable
- Quick Start Guide and Warranty Letter
Key Components:
- 1. LED indicator
- 2. Multi-function Touch Button (MFB)
- 3. MIC hole
- 4. Charging contact
- 5. Vocal position
- 6. USB-C charging port
- 7. Charging indicator light
Wearing
Put the Monster Open Ear AC600 onto your ears and rotate to fit comfortably to get the best wearing and sound quality experience.
Power On/Off
Take out the earphones from the charging case, and they will turn on automatically. Put the earphones into the charging case, and they will automatically shut down and charge.
Pairing
Take out the earphones from the charging case, and they turn on automatically. For new device connection, please turn on Bluetooth and search for "Monster Open Ear AC600" to pair. After successful connection, you will hear a system voice prompt.
Case Charging
Use the USB-C charging cable provided with the product to charge. The charging case indicator shows the charging status. When the charging case is fully charged, the charging case indicator lights up.
Music Control
- Play/pause music: Double-click the multi-function touch button (left or right earphone).
- Previous track: When connected to a mobile phone, touch the left earphone 3 times.
- Next track: When connected to a mobile phone, touch the right earphone 3 times.
Call Control
- Answer/end a call: Double-click the MFB (left or right earphone).
- Reject an incoming call: When an incoming call comes, press and hold for 2 seconds (left or right earphone).
- Cancel a call: If the caller does not answer the call after dialing, double-click to cancel the call.
Voice Control
When the earphones are connected to the phone, press and hold for 2 seconds to wake up the voice assistant (both left and right earphones can be operated).
Reset
When the earphone is on, touch both earphones 5 times at the same time. The left and right earphone white lights will flash quickly. After clearing the pairing record between the earphone and the phone (without clearing the left and right earphones), the device enters search and pairing mode. It will automatically shut down if no new device is connected within 3 minutes.
Indicator/Voice Guide
| Mode | Description | Voice Prompt |
|---|---|---|
| Power On | White light on for 1 second | System tone |
| Power Off | The red light is on for 2 seconds | System tone |
| Pairing | White light flashes quickly | System tone |
| Connected | White indicator is on for 1 second and off | System tone |
| Charging Case Charging | When charging, the red light blinks slowly, and then blinks long after it is full. | N/A |
Notes
- After removing the earphones from the charging case, they will automatically connect without pressing any button and enter pairing mode.
- Please place the earphones in the correct position for charging.
- It is not recommended to replace the battery personally without permission.
- The battery [battery pack or battery combination] shall not be exposed to lighting, baking, or similar overheating or undercooling environments.
- The charging case input voltage and current standard when charging with external power is ≤5V/1A.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
FCC ID: 2AVD2-MH22185
