MiraScreen Wireless HD Transmitter & Receiver Kit

Preface

Thank you for purchasing MiraScreen products. For optimum operation, please read this manual carefully before use.

Connection Diagram

Receiver (RX)

• Indicator Light
• USB-C Power Supply Port
• HD Port
• 3.5mm Jack

Transmitter (TX)

• Function Button
• Indicator Light
• ON-OFF Switch
• HD Port
• USB-C Power Supply Port

Hardware Casting

Combination of receiver and transmitter, plug and play.

Pairing Instructions

The product is paired at the factory. In case of pairing failure, restore and re-pair the device as follows:

1. Press and hold the receiver function button for more than 3 seconds. A prompt will appear on the interface: "Release the button to pair with Ezcast TX." Wait for the transmitter to enter pairing mode.
2. Press the transmitter function button for more than 3 seconds. The indicator will flash for pairing. Wait for the transmitter indicator to be always on, indicating a successful connection.

Note: One receiver can pair with up to 8 transmitters for switching.

Function Settings

1. Search for the receiver in Wireless Network (Name is MiraScreen-XXXX, default password is 12345678).
2. Open the mobile/tablet browser and enter 192.168.203.1 in the address bar.
3. After entering the website, you can operate distribution network, resolution, upgrade, and restart.

Software Casting

When the receiver is used alone, it needs to cooperate with the software on the mobile phone or computer. Complete the "Internet" distribution network in the Function Settings.

Apple iOS System - Operation Steps

Slide the screen to enter the Apple Device Control Center, click Airplay, and select the MiraScreen device.

Android System - Operation Steps

1. Turn on the screen casting function on your mobile phone/tablet.
2. Search for and connect to the MiraScreen device.

Different brand screen casting function path reference:

• HUAWEI: Settings > Smart Assist > Multi-screen Interactive
• Xiaomi: Settings > Connect and Share > Cast Screen
• VIVO: Settings > Other connection methods > Smart screen
• OPPO: Settings > Other connection methods > Smart screen
• MEIZU: Settings > Display > Projection Screen
• Lenovo: Settings > Display > Wireless Display
• SAMSUNG: Phone From Top To Bottom > Smart View

Please contact service for more models and brands.

Transmitter [TX] - Function Button

Transmitter Indicator Status

• Slow Flash: Disconnected
• Fast Flash: Pairing
• Always On: Connected

Setup Instructions

1. Connect the HD port or VGA port of the receiver to the video input port of the display device (e.g., monitor or TV).
2. Connect the USB-C power supply port of the receiver to the charging cable and plug it into a power adapter (Voltage above 5V, current above 2A). Turn on the Receiver power switch.
3. Adjust the HD Signal source of the monitor or TV to the corresponding HD port until the boot screen is displayed.
4. Connect the transmitter to the computer or other devices with HD video output function. After the indicator light enters the fast flash state, wait for ten seconds to complete casting.

Note: Please ensure the computer's power supply is sufficient. If the power supply is insufficient or HD cannot supply power, connect the transmitter to a power adapter or USB-C power supply port (Voltage above 5V, current above 2A).

Problem Solving

• Q: How to restore factory settings?
  A: When the product fails, press and hold the receiver function button for 10 seconds. After a black screen appears and the device restarts, the factory settings will be restored.
• Q: Can devices without an HD interface be used?
  A: Yes, please use a device with an HD interface converter.
• Q: How to enter privacy mode?
  A: Tap the transmitter function button to disconnect or reconnect.

Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE: This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.

RF Exposure Statement

To maintain compliance with FCC's RF Exposure guidelines, this equipment should be installed and operated with a minimum distance of 10cm from the radiator to your body. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.