Introduction
Thank you for purchasing a Braun shaver. This manual provides important information for the safe and effective use of your new Braun shaver. Please read it carefully and keep it for future reference.
Safety Precautions
Warnings
Warning: Indicates potential risks of death or severe injury.
Caution: Indicates potential risks of injury or property damage.
General Warnings:
- Your appliance is provided with a special cord set with an integrated Safety Extra Low Voltage power supply. Do not exchange or tamper with any part of it, as this carries a risk of electric shock. Only use the provided cord set.
- If the appliance is marked with a symbol like ☍492, it can be used with any Braun power supply coded 492-XXXX.
- The shaver is suitable for cleaning under running tap water. Always detach the shaver from the power supply before cleaning it in water.
- Do not shave with a damaged foil or cord.
- This appliance can be used by children aged 8 years and above, and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they are given supervision or instruction concerning safe use and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be performed by children unless they are older than 8 years and supervised.
Electrical Safety
- Do not use the shaver with voltages other than 100-240V AC, as this may cause fire or electric shock.
- Do not damage, bend, twist, or pull the power cord. Do not place heavy objects on it or expose it to heat, as this can cause the cord to break and lead to fire or electric shock.
- Do not use the shaver if the power cord or plug is damaged, or if the outlet is loose, as this may cause electric shock, short circuits, or fire.
- Do not disassemble or repair the appliance yourself, except for battery removal during disposal. Unauthorized repairs can lead to fire, electric shock, or injury. Contact a Braun repair center for service.
- Do not immerse the power plug in water or splash water on it. This can cause short circuits, electric shock, smoke, fire, leakage fires, or malfunctions.
- Do not use the power plug in wet areas such as bathrooms or shower rooms for the same reasons.
- Never unplug the power cord with wet hands, as this can cause electric shock or injury.
- Keep the cleaning fluid cartridge away from fire sources, as it is flammable and can cause fire.
- Always switch off the shaver and unplug the power cord before cleaning or maintenance to prevent electric shock or injury.
- Ensure the electrical contacts on the power plug are completely dry before use. Failure to do so may result in short circuits, electric shock, smoke, fire, leakage fires, or malfunctions.
- Always use the dedicated power cord supplied with the shaver. Using an incorrect cord can lead to fire, electric shock, or injury.
Usage Precautions
- Do not let children use the shaver alone or leave it within their reach to prevent accidents or injuries.
- Do not use the shaver for purposes other than shaving (e.g., for hair on the head). Doing so may damage the foil and cause skin injury or premature wear.
- Do not allow metal objects, dust, or water droplets to adhere to the power plug. This can cause short circuits, electric shock, smoke, fire, leakage fires, or malfunctions. Clean the plug periodically.
- Do not press the foil or cutter hard, as this may cause damage and skin injury.
- Do not share the shaver with others to prevent the spread of infections.
- When removing the battery for disposal, ensure the terminals are not short-circuited.
- Before each use, check the foil for any tears or deformation to prevent skin injury.
- When unplugging the shaver, always pull the plug itself, not the cord, to avoid electric shock, short circuits, or fire.
- Unplug the shaver from the outlet when not in use or when not charging (especially during extended absences) to prevent injury, burns, insulation degradation, electric shock, or leakage fires.
Parts and Specifications
Shaver Parts
The Braun Series 9 shaver is comprised of the following parts:
- Foil & Cutter Cassette: The foil and cutter are integrated into one unit.
- Cassette Release Buttons: Press these buttons to remove the foil and cutter cassette.
- MultiHeadLock Switch: Locks the shaver head in one of five positions, allowing for easier shaving of difficult-to-reach areas.
- Power Switch: Turns the shaver on and off.
- Shaver Display: Shows charging status and other indicators.
- Long Hair Trimmer: Used for trimming sideburns, mustache, or beard.
- Shaver-to-Station Contacts: Located on the back of the shaver for connection to the Clean&Charge Station.
- Release Button for Long Hair Trimmer: Releases the lock for the long hair trimmer.
- Shaver Power Socket: Port for connecting the power cord.
- Power Cord: The special cord set for charging and powering the shaver.
- Travel Case: For storing and protecting the shaver during travel.
Clean&Charge Station Parts
The Clean&Charge Station includes:
- Station Power Socket: Connection point for the power cord.
- Lift Button for Cartridge Exchange: Used to open the station for cartridge replacement.
- Station-to-Shaver Contacts: Connects with the shaver's contacts for charging and cleaning.
- Clean&Charge Station Display: Indicates cleaning fluid level and status.
- Status Light: Illuminates during cleaning and drying cycles.
- Start Button: Initiates the cleaning and charging cycle.
- Cleaning Cartridge: Contains the cleaning fluid.
Specifications
| Item | Details |
|---|---|
| Power Source | Rechargeable / AC |
| Battery | Lithium-ion |
| Charging Time | 1 Hour |
| Power Consumption | 7W |
| Rated Voltage | AC100-240V 50-60Hz |
| Weight | 210g |
| Dimensions (h x w x d) | 168 x 66 x 44mm |
| Accessories Included | Power cord, Clean&Charge System, Travel case, Brush (1 each) |
Note: Specifications are subject to change without notice.
Operation
First Use and Charging
Connect the shaver to an electrical outlet using the special cord set (10) into the power socket (9), or via the Clean&Charge Station. For first-time use, charge the shaver continuously for 1 hour.
Charging and Basic Operating Information
- Recommended Ambient Temperature for Charging: 5°C to 35°C. Temperatures outside this range may affect charging performance.
- Recommended Ambient Temperature for Shaving: 15°C to 35°C.
- Temperature Limits: Do not expose the appliance to temperatures higher than 50°C for extended periods.
- Charging Time: A full charge provides up to 50 minutes of cordless shaving time. This may vary based on beard growth and environmental conditions.
- Shaving with Cord: You can also shave by connecting the shaver directly to an electrical outlet via the special cord set if the battery is discharged.
- Display Illumination: When connected to an electrical outlet, the shaver display may take a few minutes to illuminate.
Shaver Display
The shaver display (5) indicates the battery's charge status:
- Charge Status: Battery segments blink during charging. All segments light up briefly when fully charged, then turn off.
- Low Charge: A low-charge light ([low battery symbol]) flashes red when the battery is low. You should still be able to finish your shave. A beep sound will remind you of the low charge status when switching off the shaver.
- Cleaning Status: A cleaning indicator ([cleaning symbol]) lights up when the shaver requires cleaning in the Clean&Charge Station.
- Travel Lock: A lock symbol ([lock symbol]) lights up when the shaver is locked to prevent accidental activation, such as when stored in a suitcase.
Using the Shaver
Press the on/off switch (4) to operate the shaver.
Tips for a Perfect Dry Shave
- Always shave before washing your face for optimal results.
- Hold the shaver at a 90° angle to your skin at all times.
- Stretch your skin and shave against the direction of your beard growth.
MultiHeadLock Switch (Head Lock)
To shave hard-to-reach areas (e.g., under the nose), slide the MultiHeadLock switch (3) down to lock the shaver head. The shaver head can be locked in five positions. To change positions, move the shaver head forward or backward with your thumb and forefinger; it will click into the next position automatically. For automatic cleaning in the Clean&Charge Station, the head lock should be released (slide switch up).
Long Hair Trimmer
To trim sideburns, mustache, or beard, press the release button (8) and slide the long hair trimmer (6) upwards. Caution: Do not slide the trimmer horizontally on the skin, as this may cause cuts.
Travel Lock
- Activation: Press and hold the on/off switch (4) for 3 seconds. The shaver will lock, confirmed by a beep sound and the lock symbol on the display. The display will then turn off.
- Deactivation: Press and hold the on/off switch (4) for 3 seconds again to unlock the shaver.
Cleaning and Maintenance
Manual Cleaning of the Shaver
Cleaning Under Running Water
- Switch on the shaver (cordless) and rinse the shaver head under hot running water until all residue is removed. You may use liquid soap without abrasive substances. Rinse off all foam and let the shaver run for a few more seconds to remove remaining water.
- After rinsing, switch off the shaver, press the cassette release buttons (2) to remove the Foil & Cutter cassette (1), and let it dry completely.
- If you regularly clean the shaver under water, apply a drop of light machine oil (not included) on top of the Foil & Cutter cassette and the long hair trimmer once a week for lubrication.
Cleaning with a Brush
- Switch off the shaver. Remove the Foil & Cutter cassette (1) and tap it out on a flat surface to remove debris.
- Using the supplied brush, clean the inner area of the pivoting head. Caution: Do not brush the foil or inner blades, as this may damage them.
The Foil & Cutter cassette can be attached in either orientation without affecting shaving performance.
Clean&Charge Station Cleaning
The Clean&Charge Station is designed for cleaning, charging, lubricating, disinfecting, drying, and storing your Braun shaver.
Installing the Clean&Charge Station
- Press the lift button (13) at the rear of the station to raise the housing.
- Hold the cleaning cartridge (17) on a flat, stable surface (e.g., a table) and carefully remove its lid.
- Slide the cartridge from the rear into the base of the station until it clicks into place.
- Slowly push the housing down until it locks.
- Connect the station to an electrical outlet by attaching the special cord set (10) to the power socket (12).
Charging the Shaver in the Clean&Charge Station
Insert the shaver head first, with the front showing and the head lock released, into the cleaning station. Important: The shaver must be dry and free from foam or soap residue. Align the shaver's contacts (7) on the back with the station's contacts (14). Push the shaver into the correct position. A beep sound confirms proper placement, and charging will start automatically.
Cleaning the Shaver
When the cleaning indicator ([cleaning symbol]) lights up on the shaver display, insert the shaver into the Clean&Charge Station as described above and press the start button (16). If the status light (15b) does not shine (indicating the station has entered standby mode after about 10 minutes), press the start button twice. Cleaning will not start otherwise. For best results, cleaning after each shave is recommended.
The cleaning process involves several cycles of flushing with cleaning fluid (approximately 3 minutes), followed by an active drying phase (approximately 40 minutes) with a fan running. Charging will resume afterwards, indicated on the shaver display. The display turns off when the shaver is fully charged.
Removing the Shaver from the Clean&Charge Station
Hold the Clean&Charge Station with one hand and tilt the shaver slightly forward to release it.
Cleaning Cartridge / Replacement
When the level indicator (15a) lights up permanently red, there are approximately 3 more cycles of fluid remaining. When the level indicator blinks red, the cartridge needs replacement (roughly every 3 weeks with daily use). After pressing the lift button (13) to open the housing, wait a few seconds before removing the used cartridge to prevent dripping. Before discarding the used cartridge, close its openings with the lid of the new cartridge, as the used cartridge contains contaminated cleaning solution.
Consumables
Braun recommends replacing your shaver's Foil & Cutter cassette every 18 months to maintain maximum performance. These are available from your dealer or Braun Service Centres.
- Foil & Cutter Cassette: Models 92S/92B.
- Cleaning Cartridges: CCR2CR (2-pack), CCR3CR (3-pack), CCR4CR (4-pack), CCR6CR (6-pack).
Important: Do not reuse cartridges with water or other liquids. Always use genuine Braun cleaning cartridges.
Troubleshooting
| Problem | Possible Reason | Remedy |
|---|---|---|
| SHAVER | ||
| Shaver does not start when pressing the start button. | Travel lock is activated. | Press the on/off switch for 3 seconds to unlock the shaver. |
| Shaver does not charge completely and keeps blinking. | Ambient temperature is out of valid range. | Recommended ambient temperature for charging is 5°C to 35°C. |
| Charging does not start when connected to power socket or put in the Clean&Charge Station. | 1. Shaver is not placed properly in the Clean&Charge Station. 2. Sometimes charging could start delayed (e.g. after long storage). 3. Ambient temperature is out of valid range. 4. Special cord set is not plugged in properly. | 1. Ensure shaver contacts align with station contacts. 2. Wait a few minutes; charging should start automatically. 3. Recommended ambient temperature for charging is 5°C to 35°C. 4. Ensure the special cord set is securely connected. |
| Unpleasant smell from the shaver head. | 1. Shaver head is cleaned with water only. 2. Cleaning cartridge is in use for more than 8 weeks. | 1. When cleaning with water only, use hot water and mild soap. Remove Foil & Cutter cassette to let it dry. 2. Change cleaning cartridge at least every 8 weeks. |
| Battery performance dropped significantly. | 1. Shaver head is regularly cleaned with water but not lubricated. 2. Foil and cutter are worn, requiring more power for each shave. | 1. If regularly cleaned with water, apply a drop of light machine oil on the foil weekly for lubrication. 2. Replace Foil & Cutter cassette. |
| Shaving performance dropped significantly. | 1. Shaving system is clogged. 2. Foil and cutter are worn. | 1. Soak the Foil & Cutter cassette in hot water with a drop of dish liquid. Rinse properly, tap dry, and apply a drop of light machine oil once dry. 2. Replace Foil & Cutter cassette. |
| Shaver turns off with fully charged battery. | Foil and cutter are worn, requiring more power than the motor can deliver. The appliance turns off. | Replace Foil & Cutter cassette. Regularly oil the shaving system, especially when cleaning with water only. |
| Shaver head is damp. | 1. Drain of the Clean&Charge Station is clogged. 2. Cleaning cartridge has been used for quite a while. | 1. Clean the drain with a wooden toothpick. 2. The alcohol/isopropanol proportion has decreased while the oil proportion has increased. Remove residue with a cloth. |
| CLEAN&CHARGE STATION | ||
| Cleaning does not start when pressing the start button. | 1. Shaver is not placed properly in the Clean&Charge Station. 2. Cleaning cartridge does not contain enough cleaning fluid (level indicator blinks red). 3. Appliance is in standby mode. | 1. Insert shaver into the Clean&Charge Station, ensuring contacts align. 2. Insert a new cleaning cartridge. 3. Press the start button again. |
| Increased consumption of cleaning fluid. | Drain of the Clean&Charge Station is clogged. | Clean the drain with a wooden toothpick. Regularly wipe the tub clean. |
Warranty and After-Sales Service
Warranty Information
Please ensure the warranty card is properly filled out by the retailer with the date of purchase and your name. The manufacturer's warranty is valid for one year from the date of purchase. Consumables and accessories are not covered by the warranty, except where specified on the warranty card.
Requesting Repair Service
If your shaver malfunctions or exhibits abnormal behavior, stop using it immediately and contact a Braun repair center or your retailer. For in-warranty service, present your warranty card. Out-of-warranty repairs are available for a fee.
Spare Parts Availability
Spare parts for this product are kept for 6 years after the product is discontinued.
Battery
If battery performance significantly decreases despite proper charging, the battery may be worn out. Contact your retailer or a Braun repair center. Battery replacement is a paid service. Do not attempt to remove the battery except for disposal.
After-Sales Support
For any questions or concerns, please contact your retailer or the Braun Customer Service.
Braun Product Service Contacts
- Braun Customer Service:
- For general inquiries: 0120-136343 (Mon-Fri, 9:00-17:30, excluding holidays)
- Website: http://www.braun.com/jp
- Braun Repair Center:
- For repair inquiries: 049-281-2033 (Mon-Fri, 9:30-12:30 / 13:30-17:30, excluding holidays)
- Address: 5-7-3 Nissa-Hanamizu-ki, Sakado-shi, Saitama 350-0269
- Website: http://braun-service.jp
Please note: Phone numbers and operating hours are subject to change.
Product Checks and Disposal
Long-Term Use Product Check
Periodically check your electric product for the following symptoms:
- Intermittent or failed startup.
- Cord issues (intermittent power, overheating).
- Unusual noises or vibrations during operation.
- Appliance deformation, burning smell, or physical damage.
- Extended charging times or rapid battery drain.
- Any other abnormal behavior or malfunction.
Action Required: If you notice any of these symptoms, stop using the product immediately. Turn it off and unplug it from the power outlet. Contact a Braun repair center or your retailer for assistance. Continued use may lead to further malfunction or fire hazards.
Safety Information
For general safety information regarding electrical appliances, please refer to the Japan Electrical Appliances Safety Association website: http://www.aeha.or.jp
Product Disposal
Environmental Notice: This product contains batteries and/or recyclable electric waste. To protect the environment, do not dispose of it with regular household waste. Please take it to designated electric waste collection points in your country.
Battery Disposal: The product uses a rechargeable Lithium-ion battery. Warning: Never disassemble the product or its battery, as this can cause fire, electric shock, or injury. Ensure the battery is fully discharged before disposal. When removing the battery, insulate the terminals (e.g., with tape) to prevent short circuits. Take the battery to a small secondary battery recycling collection point.
For information on recycling collection points, visit the Japan Battery Recyclers Association (JBRC) website: http://www.jbrc.com
Content is subject to change without notice.
Privacy Policy
Personal information collected from customers is used solely for responding to inquiries and requests, and for related services. Your personal information is stored securely within P&G group databases. P&G will not share your information with external parties without your consent. In some cases, P&G may share minimal personal information with service providers to fulfill requests, but these providers are bound by strict confidentiality agreements and are prohibited from using the information for any other purpose. For detailed information, please refer to the P&G Privacy Policy: http://www.pg.com/privjp (PC only).
