DigiTech Metal Master Heavy Metal Distortion

Product Controls and Features

The pedal features the following controls and connections:

• Level Knob (1): Controls the effect's output level. Turning clockwise increases the output level; counter-clockwise decreases it.
• Low Knob (2): Controls the boost or cut of low frequencies. Turning clockwise increases low frequency content; counter-clockwise decreases it.
• High Knob (3): Controls the boost or cut of high frequencies. Turning clockwise increases high frequency content; counter-clockwise decreases it.
• Morph Knob (4): Blends between three different metal distortion voicings. The minimum position offers a smooth high gain tone. At the 12 o'clock position, it provides a scooped midrange sound. The maximum position delivers a punchy mid-range heavy metal sound that cuts through the mix. Experiment with different positions for a wide variety of tones.
• Pedal (8): Press the pedal to turn the effect on and off. The Indicator LED (10) illuminates when the effect is active.
• Input Jack (6): Connect your instrument (e.g., guitar) to this jack. Connecting a guitar cable engages battery power, even if the Indicator LED is not lit. Disconnect all cables when not in use to prolong battery life.
• Out 1 (Amp) Jack (9): Connect this output to your guitar amplifier.
• Out 2 (Mixer) Jack (11): This output utilizes DigiTech's CIT™ cabinet modeling technology, allowing the pedal to be run directly into a mixer or recorder input without needing a guitar amplifier.
• AC Adapter Jack (3): Connect a DigiTech PS200R power supply to this jack. Ensure the supply matches your area's mains line voltage.
• Pedal Release Pins (7): These spring-loaded pins hold the pedal in place. Push them in to release the pedal from the chassis and access the battery compartment.

Connections Diagram Description

The connection diagram illustrates:

• A guitar connected to the pedal's INPUT jack.
• The pedal's OUT 1 (AMP) jack connected to an AMPLIFIER.
• The pedal's OUT 2 (MIXER) jack connected to a MIXER console.
• An optional PS200R power supply connected to the pedal's AC adapter jack.

Setup Directions

Follow these steps before use:

1. Turn the volume down on the amplifier/mixer you are connecting to.
2. Connect the pedal's output (OUT 1 or OUT 2) to the amplifier/mixer input.
3. Connect your guitar to the pedal's INPUT jack.
4. Connect the power supply to the pedal (optional).
5. Turn the Level control on the pedal to its minimum position.
6. Turn up your amplifier/mixer level to the desired listening level.
7. Turn on the pedal by pressing the pedal switch and gradually increase the level to your desired listening volume.

Battery Replacement

To replace the battery:

1. Using the tip of a 1/4" guitar cable, push one of the release pins on either side of the pedal to detach it from the chassis.
2. Remove the old battery from the battery compartment and disconnect its cable.
3. Connect a new battery to the cable and place it in the battery compartment, ensuring the cable does not interfere with the spring or pedal switch arm.
4. Align one hole of the pedal with its corresponding pin on the chassis.
5. Push the opposite pin in and lower the other side of the pedal into place over the depressed pin. Release the pin. When properly fastened, both release pins should be flush with the outer side of the pedal.

Specifications

Declaration of Conformity

Manufacturer's Name: DigiTech

Manufacturer's Address: 8760 S. Sandy Parkway, Sandy, Utah 84070, USA

Product Name: Metal Master

Product Option: All (requires Class II power adapter conforming to EN60065, EN60742, or equivalent requirements.)

Product Specifications Conformance:

• Safety: IEC 60065 (1998)
• EMC: EN 55013 (1990), EN 55020 (1991)

Supplementary Information: The product complies with the Low Voltage Directive 72/23/EEC and the EMC Directive 89/336/EEC, as amended by Directive 93/68/EEC.

Declaration Date: February 22, 2002

European Contact: Your local DigiTech Sales and Service Office or Harman Music Group, 8760 South Sandy Parkway, Sandy, Utah 84070 USA. Phone: (801) 566-8800, Fax: (801) 568-7583.

Warning and Safety Instructions

Important Safety Instructions:

1. Read and keep these instructions.
2. Heed all warnings.
3. Do not use this apparatus near water.
4. Clean only with a dry cloth.
5. Do not block ventilation openings; install per manufacturer's instructions.
6. Do not install near heat sources like radiators, heat registers, stoves, or other heat-producing apparatus (including amplifiers).
7. Protect the power cord from being walked on or pinched, especially at plugs and where it exits the apparatus.
8. Unplug during lightning storms or when unused for long periods.
9. No user-serviceable parts inside. Refer all servicing to qualified personnel. Servicing is required for damage such as a damaged power cord/plug, spilled liquid, fallen objects, exposure to rain/moisture, abnormal operation, or dropping.
10. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
11. Refer to unit labels (including bottom cover) and other markings for pertinent information.

Warranty Information

DigiTech provides the following warranty for its products:

1. Warranty validation requires mailing the registration card within ten days of purchase.
2. DigiTech warrants the product, when used in the U.S., to be free from defects in materials and workmanship under normal use and service.
3. DigiTech's liability is limited to repairing or replacing defective materials. Products must be returned to DigiTech with a Return Authorization number. Parts and labor are covered for one year, extended to six years if the product is properly registered.
4. Proof-of-purchase is the consumer's responsibility.
5. DigiTech reserves the right to make design changes or improvements without obligation to install them on previously manufactured products.
6. The warranty is void if the product's main assembly is opened or tampered with by unauthorized personnel, or if used with AC voltages outside the manufacturer's suggested range.
7. This warranty is in lieu of all other warranties, expressed or implied. DigiTech assumes no obligation or liability beyond this warranty. DigiTech or its dealers are not liable for special, consequential damages, or delays due to causes beyond their control.

Note: Information in this manual is subject to change without notification. Some information may be inaccurate due to undocumented product or operating system changes. This version supersedes all previous versions.