Important Note
Do not discard packaging until the product has been successfully installed.
Customer Notification and Disclaimer Liability
This product is a modification for utility task vehicles and all-terrain vehicles. Use this product at your own risk.
Warranty and Liability Limitations: Buyer assumes all risks associated with the use and/or installation of this product and waives all liability claims against SuperATV®. SuperATV® is not liable for any direct, indirect, incidental, consequential, or special damages, including but not limited to, damage, loss of life, property damage, loss of profits, or injury arising from the use of this product.
Factory Warranty: Installation of this product may void or adversely affect your vehicle's factory warranty. Consult your vehicle warranty before use. SuperATV® is not liable for any voidance of the Buyer's vehicle warranty.
Safety and Laws: Operate your vehicle safely and abide by all local, state, and federal laws, including traffic laws and ordinances. Buyer is responsible for understanding and complying with all applicable laws regarding product installation and use. Use of this product on public streets, roads, or highways may be a violation of law. Buyer is solely responsible for any legal violations.
Vehicle Capability: Buyer is responsible for understanding their vehicle's capabilities and limitations according to manufacturer specifications and agrees to hold SuperATV® harmless from any damage resulting from failure to adhere to these specifications. Buyer must also obey all applicable federal, state, and local laws when operating their vehicle with this product.
Installation Acceptance: By installing this product, Buyer acknowledges they have had the opportunity to inquire about applicable laws, have read and understood this disclaimer, and accept its terms. SuperATV® is not responsible for proper installation, use, or service; Buyer is solely responsible for installation and any resulting damage.
Installation Instructions
Read instructions and view illustrations before beginning.
Step 1: Component Removal
Remove components shown from each side of the machine. Keep all removed components.
Visual Description: Images show the front of a Polaris RZR XP 1000. Arrows labeled "remove" indicate areas on the fascia, bumper, and radiator shroud. A close-up view shows fasteners securing the stock winch and surrounding components.
If applicable, remove the stock winch.
Note: Reinstall components after winch installation is complete.
Step 2: Mount Installation
Install the Mount to the machine using the hardware shown; tighten.
Visual Description: An image depicts the underside of the RZR's front end (Driver Side view), showing the Mount being attached to the vehicle's frame using "4x - M10 x 20mm" hardware.
Step 3: Winch to Winch Plate Installation
Install the Winch to the Winch Plate using the hardware shown; tighten.
Visual Description: An illustration shows a Winch Plate with a Winch mounted onto it. Hardware is identified as "hardware included with Winch".
Step 4: Winch Plate to Mount Installation
Install the Winch Plate (with the Winch attached) to the Mount using the hardware shown; tighten.
Visual Description: An image shows the Winch and Winch Plate assembly being attached to the previously installed Mount on the vehicle. Hardware indicated is "4x - M8 x 20mm".
Step 5: Winch Wiring
Connect the Winch Wiring. Refer to the separate "Winch Guide" for detailed wiring instructions.
Visual Description: A close-up image shows electrical connections on the winch motor, with wires being connected to terminals.
Step 6: Fairlead to Skid Panel Installation
Install the Fairlead to the Skid Panel using the hardware shown; tighten. Use Fairlead and hardware included with the Winch.
Visual Description: An illustration shows the Skid Panel and Fairlead. The Fairlead is attached to the Skid Panel using bolts and washers, indicated by dashed lines.
Step 7: Fairlead Adapter Installation (If Applicable)
Depending on the Winch size, a Fairlead Adapter may need to be installed to the Skid Panel with the hardware shown; tighten.
Install the Fairlead to the Fairlead Adapter; tighten. Use Fairlead and hardware included with the Winch.
Visual Description: An illustration shows the Skid Panel. First, the Fairlead Adapter is attached to the Skid Panel, then the Fairlead is attached to the Fairlead Adapter, using indicated hardware and dashed lines.
Step 8: Skid Panel to Mount Installation
Install the Skid Panel to the Mount using the hardware shown; tighten.
Visual Description: An image shows the Skid Panel being attached to the Mount assembly on the vehicle. Hardware indicated is "4x - M8 x 16mm".
Step 9: Reinstall Stock Plastic
Reinstall the stock plastic components that were removed in Step 1.
Visual Description: An image shows the front of the RZR with the installed winch mount assembly. An arrow indicates where original plastic trim pieces should be reattached.
Step 10: Fascia Installation
Install the Fascia to the machine and the Skid Panel using the hardware shown; tighten.
Visual Description: An image shows the front fascia being attached to the vehicle and the Skid Panel, secured by "2x - M6 x 20mm" screws.
Support Information
Need help with your installation?
Email: sales@superatv.com
Phone: 1-855-743-3427
Website: www.superatv.com
Support Hours:
- 8:00am - 8:00pm EST Monday - Thursday
- 8:00am - 7:00pm EST Friday
- 9:00am - 2:00pm EST Saturday
© 2023 SuperATV.com®. All Rights Reserved.
Aftermarket ATV-UTV Parts and Accessories
