Behringer WING-DANTE Quick Start Guide

Important Safety Instructions

Warning: Terminals marked with the symbol ⚡ carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼" TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.

Warning: This symbol ⚡, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure – voltage that may be sufficient to constitute a risk of shock.

Warning: This symbol !, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual.

Caution: To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user-serviceable parts inside. Refer servicing to qualified personnel.

Caution: To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with liquids, such as vases, shall be placed on the apparatus.

Caution: These service instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualified service personnel.

Warning: Please refer to the information on the exterior of bottom enclosure for electrical and safety information before installing or operating the device.

1. Please read and follow all instructions and warnings.
2. Keep the apparatus away from water (except for outdoor products).
3. Clean only with dry cloth.
4. Do not block ventilation openings. Do not install in a confined space. Install only according to manufacturer's instructions.
5. Protect the power cord from damage, particularly at plugs and appliance socket.
6. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
7. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other (only for USA and Canada). A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
8. Use only attachments and accessories recommended by the manufacturer.
9. Use only specified carts, stands, tripods, brackets, or tables. Use caution to prevent tip-over when moving the cart/apparatus combination.
10. Unplug during storms, or if not in use for a long period.
11. Only use qualified personnel for servicing, especially after damage.
12. The apparatus with protective earthing terminal shall be connected to a MAINS socket outlet with a protective earthing connection.
13. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
14. Avoid installing in confined spaces like bookcases.
15. Do not place naked flame sources, such as lighted candles, on the apparatus.
16. Operating temperature range 5° to 45°C (41° to 113°F).

Legal Disclaimer

Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2024 All rights reserved.

Limited Warranty

For the applicable warranty terms and conditions and additional information regarding Music Tribe's Limited Warranty, please see complete details online at community.musictribe.com/support.

Installation and Setup

The WING-DANTE card is an expansion card for the WING console, enabling 64x64 channels of audio over a standard Ethernet IP network using the Dante protocol. It supports single or redundant Ethernet connections.

Card Description

The WING-DANTE card features:

• Two Neutrik EtherCON connectors.
• An ACT/LINK LED that indicates a valid IP network connection (green).
• A 1 G LED that indicates operation on a 1 GBit/s network (amber).
• Two small handles (St) for easy removal from the slot.
• Two outer screws (M3 x 6) for securing the card in the slot.
• Three countersunk screws that fix the PCBA to the bracket (do not remove these).

Installation Precautions

General Safety:

• Always ensure the console power is OFF before installing the card to prevent malfunctions or electric shock.
• Touch the console's grounded metal chassis before handling the card to discharge static electricity.
• Handle the card by its faceplate or small handles, avoiding contact with components on the circuit board.
• Align the card with the slot guides and insert it carefully. Ensure it slides in smoothly and is fully seated.
• Secure the card with the provided screws.
• If removing a previous card, store it safely in the WING-DANTE's protective bag.

System Requirements

Refer to audinate.com for PC hardware and software requirements (Minimum System Requirements). Dante Virtual Soundcard drivers are optionally available at audinate.com.

Connection Scenarios

5.1 WING-DANTE Connection to Dante Network

This setup involves connecting the WING console via a network router to a PC and other Dante-enabled audio devices. The PC can simultaneously perform three tasks: run Dante Controller for signal routing, run Dante Virtual Soundcard (DVS) for recording/playback, and run editing/control applications.

5.2 WING-DANTE Direct Connection to PC/Mac and Dante Virtual Soundcard

This scenario describes a direct connection from the WING console to a PC or Mac using Dante Virtual Soundcard for recording/playback of up to 64x64 channels.

5.3 WING-DANTE Redundant Network Infrastructure

This setup utilizes two separate routers with independent wiring to connect to a second WING, X32, or other Dante-enabled device, ensuring redundant network connectivity.

5.4 WING-DANTE Connection to Midas HD96-24 with Dante Option

This illustrates connecting the WING console with the WING-DANTE card to a Midas HD96-24 console using Cat 5/6 AES50 and Cat 5/6 Ethernet cables.

WING Setup

6.1 Routing

Access the Routing screen by pressing the ROUTING button on the WING console. Select WING-DANTE from the Input Group menu to configure all 64 channels, including names, scribble strips, and tags. Icons at the top of the Routing screen allow selection of Inputs or Outputs. Routing is performed from the console's perspective; selecting Outputs routes signals to the Dante network. Press the unlock icon to edit output routing. Switching to Inputs allows routing signals from the Dante network to input channels or physical outputs.

Refer to audinate.com for comprehensive documentation, FAQs, and forum advice on configuring Dante Controller and Dante Virtual Soundcard applications.

6.2 Synchronization

Card settings, including clock synchronization, can be adjusted via the Dante Controller application. A master word clock source must be selected for the network. Users can choose between the WING's internal clock or the WING-DANTE clock. In Dante Controller, the WING-DANTE card may appear with its chip name (e.g., BKLYN-II-06f732), but a new name can be assigned in the Device View window.

Audinate Software Tools

Dante Controller

Dante Controller is Audinate's software application for configuring and routing audio across Dante networks. It is available for PCs (Windows) and Macs (OSX 10.5). Dante Controller must be installed on at least one PC/Mac on the Dante network to change signal routing or clocking. It is not required if the network is pre-configured for audio transmission between Dante devices.

Dante Virtual Soundcard

Dante Virtual Soundcard transforms your PC or Mac into a Dante-enabled device, enabling Dante audio traffic transmission and reception via a standard Ethernet port without additional hardware. On Windows, it uses Steinberg's ASIO audio interface and is compatible with ASIO/WDM audio applications. On Mac OSX, it uses the standard Core Audio interface and is compatible with most standard audio applications. Visit audinate.com for download and licensing information.

Federal Communications Commission Compliance Information

This equipment complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Music Tribe can void the user's authority to use the equipment.

This product complies with relevant EU directives (2014/30/EU, 2011/65/EU, 2012/19/EU, 519/2012, 1907/2006/EC). EU Representative: Music Tribe Brands DK A/S. UK Representative: Music Tribe Brands UK Ltd.

Correct Disposal: This symbol indicates that the product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU). Take it to a licensed collection center for recycling of waste electrical and electronic equipment (EEE). Proper disposal helps prevent negative environmental and health impacts and promotes efficient use of natural resources.