DIGITAL MIXER OPTION X-ADAT

Introduction

The X-ADAT card is a multi-channel audio interface expansion card for the X32 series digital mixers. It provides 32 channels of input and output via 8 Toslink interfaces and wordclock synchronization via a coaxial interface. This interface is ideal for recording with standalone ADAT hard disk recorders and offers unique digital insert options for integrating external processors and ADAT connections.

Installation

Before installing the X-ADAT expansion card into the X32 mixer's expansion slot, please visit behringer.com to confirm that the mixer's firmware supports this expansion card.

Important: Before installing the X-ADAT expansion card into the mixer, ensure the mixer's power is turned OFF. Failure to do so may cause malfunctions or electric shock.

1. Ensure the mixer's power is turned OFF.
2. Unscrew the two screws on the left and right of the expansion slot, remove the slot cover or the currently installed expansion card, and place it in a safe location.
3. Before removing the X-ADAT expansion card from its protective bag, it is recommended to touch the mixer's grounded metal chassis to prevent electrostatic discharge that could affect sensitive electronic components. It is best to hold the expansion card by gripping the panel or the two small handles, but do not directly touch the components on the circuit board.
4. Align the expansion card's two ends with the guides in the slot, and carefully insert the expansion card into the slot. Continue pushing the expansion card into the slot until the card's contacts are properly inserted into the internal interface.
5. Secure the expansion card using the supplied screws. Ensure the expansion card is securely fastened, otherwise, it may cause damage or malfunction.

Requirement: The firmware version of the X32 series mixers should be 2.0 or higher.

Connection Board

The X-ADAT card features:

• A single BNC coaxial connector for input/output, switchable, with no internal termination. The LED indicates WC output (master mode).
• 4 Toslink input connectors and 4 Toslink output connectors, providing 8 channels per interface.
• 2 small handles for removing the expansion card from the slot.
• 2 M3x6 screws for securing the expansion card in the slot.
• 3 small countersunk screws for securing the PCB. Do not loosen these screws.

Connection Diagram

X-ADAT → External Hard Disk Recorder (Wordclock provided via BNC coaxial connection)

Diagram shows Behringer X32 with X-ADAT connected via Coaxial to a Hard disc recorder Recorder.

2x ADA8200 → X32 COMPACT Input channels 17-24 and 25-32

Diagram shows two ADA8200 units connected via Optical to an X32 COMPACT, routing signals to input channels 17-24 and 25-32.

X32 Installation

The X-ADAT card can be selected as the clock source on the X32 Setup/config page. In this case, the X32 will be slaved to the ADAT clock received from the BNC input or Toslink input. Note that if the internal and external clock frequencies differ (e.g., 44.1/48 kHz), the mixer must be restarted.

Word Clock I/O and Sync Source Selection:

Word Clock I/O:

• Sync Source: Selectable between Local Clock, Slave mode (input) for synchronizing the console to an external word clock, and Master mode (output) for providing system word clock to external devices.
• BNC Word Clock I/O: A single BNC connector for input/output, switchable.

Clock Source Selection for ADAT Input/Output:

• Select ADAT clock source: Either use ADAT clock from the BNC input or Toslink input for synchronization.
• Fiber Optic Input 1-4 or Coaxial BNC Word Clock Input: These are the selectable clock sources.
• Internal Clock: Indicates the X32 mixer's internal clock.

When synchronizing the console to an external WC or ADAT source, ensure Clock Synchronization is set to "X-ADAT" on the Setup/config page.

Important Safety Information

Warnings

• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with a dry cloth.
• Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
• Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
• Only use attachments and accessories specified by the manufacturer.
• Only use carts, stands, tripods, brackets, or tables specified by the manufacturer or that are sold with the apparatus. If a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
• Unplug this apparatus during lightning storms or when unused for long periods.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
• The apparatus must be connected to a grounded mains socket.

Additional Safety Notes

• If the power plug or appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
• This product is intended for use in areas with an altitude of up to 2000 meters. It is suitable for non-tropical climates.

Legal Statement

• MUSIC Group accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners.
• MIDAS, KLARK TEKNIK, LAB GRUPPEN, LAKE, TANNOY, TURBOSOUND, TC ELECTRONIC, TC HELICON, BEHRINGER, BUGERA and DDA are trademarks and belong to MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2017. All rights reserved.

Warranty Terms

• For the applicable warranty terms and other related information from Music Group, please visit music-group.com/warranty for complete details.

Technical Specifications