Super Bright LEDs Wireless Dimming System
User Manual for PPA401S Dimming Module and WP4013 Dimmer Switch
Important Information
Please read all instructions prior to installation.
Safety and Notes
- Product must be installed and serviced according to applicable national, state, and local building and electrical codes.
- To reduce the risk of electric shock, ensure the main power source and circuit breakers are switched off before installation or wiring.
- Each dimming module (PPA401S) can be paired with up to five dimmer switches (WP4013).
- Dimmer switches can be paired with multiple dimming modules.
- Dimmer switches should be paired one at a time.
Specifications
General Specifications
| Parameter | Value |
|---|---|
| Operating Temperature | -4° to 104° F (-20° to 40° C) |
| IP Rating | IP20 |
| Radio Frequency | 433.96 MHz |
| RF Range | 98.4 ft (30 m) |
WP4013 Specifications
| Parameter | Value |
|---|---|
| Battery Type | CR2032 (x1, not included) |
Check product label for specific electrical specifications related to installation. Improper installation will void warranty.
Dimming Module (PPA401S) Installation
- With supply power off, connect wiring as shown in the diagram. Note: Open knockout on fixture or junction box prior to this step if needed.
- Mount the dimming module.
- Follow pairing instructions for the intended controller (dimmer switch, WP4013). Note: To unpair, hold the PAIR button for 5 seconds. You will hear four beeps to confirm unpairing is complete.
Wiring Diagram Description: The diagram illustrates the PPA401S dimming module connections. The Black wire connects to the 120–277 VAC Input (Line). The White wire connects to Neutral. The Red wire serves as the Line Output to the Driver. The Pink wire is for DIM (-) and the Purple wire is for DIM (+). A PAIR button is visible on the module.
Multiple lights can be controlled with one dimming module, provided the maximum load (10 A) is not exceeded. Dimming wires can be connected through conduit-side wires or an external connector on the controller body, but should not be connected to both simultaneously.
Dimmer Switch (WP4013) Installation
- Being careful to avoid any live wires, install the full wall plate or adapter plate with the tab on the bottom side as shown in the diagram.
- Install the CR2032 battery (not included) into the remote, but do not install the remote into the wall plate at this time.
- With the dimming module powered on, press the PAIR button on the module. The LED on the module will flash quickly.
- Hold the ON/OFF button on the remote for 3 seconds to pair with the dimming module. An audible beep indicates the remote has been paired with the dimming module.
- Test the remote to confirm successful pairing. Note: Up/Down buttons respond to individual presses and will not make continual adjustments if held down.
- Once pairing is complete, slide the remote into the wall plate. Note: Removal of the remote will require removal of the wall plate.
Remote Installation Diagram Description: The diagram shows the WP4013 dimmer switch remote and its installation into a wall plate. The remote slides into the plate, which has a tab on the bottom.
Battery Safety
- Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.
- Even used batteries may cause severe injury or death.
- Call a local poison control center for treatment information.
- Non-rechargeable batteries are not to be recharged.
- Do not force discharge, recharge, disassemble, heat above the manufacturer's specified temperature rating, or incinerate. Doing so may result in injury due to venting, leakage, or explosion, resulting in chemical burns.
- Ensure batteries are installed correctly according to polarity (+ and -).
- Do not mix old and new batteries, different brands, or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
- Remove and immediately recycle or dispose of batteries from equipment not used for an extended period according to local regulations.
- Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.
WARNING: INGESTION HAZARD: This product contains a button cell or coin battery. DEATH or serious injury can occur if ingested. A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours. KEEP new and used batteries OUT OF REACH of CHILDREN. Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.
