Intelbras PGM 8000 User Guide

Introduction

Congratulations on purchasing the Intelbras PGM 8000 expander, a product designed with Intelbras quality and security. This module features a relay output, enabling users to automate various devices in homes or businesses, such as gates, automatic curtains, lamps, and more.

1. Care and Security

• Follow all instructions in the manual/guide for product installation and handling.
• Perform installation in environments protected from rain, fog, and water splashes.
• Wireless communication may experience interference in areas with high-power radiation (e.g., near TV towers, radio stations).
• Clean the device exterior only with a damp cloth; do not use chemical solvents.
• Avoid subjecting the device to excessive pressure or impacts/falls.
• Do not cover the device with adhesives, paper, or inks.
• Do not expose the device directly to sunlight.
• Confirm the installation site is stable and appropriate.
• Only qualified personnel should perform configurations and installations.

This product contains an internal battery. Upon reaching the end of its useful life, the product must be delivered to an Intelbras authorized technical assistance center or disposed of appropriately to avoid environmental and health impacts. For disposal, batteries and other Intelbras electronics can be taken to any Green Eletron collection point. For questions about reverse logistics, contact Intelbras at (48) 2106-0006 or 0800 704 2767 (Monday to Friday, 8 AM to 8 PM; Saturdays, 8 AM to 6 PM) or email suporte@intelbras.com.br.

LGPD (General Law for the Protection of Personal Data): Intelbras does not access, transfer, capture, or perform any other treatment of personal data from this product.

?️ ?

2. Technical Specifications

¹ Intelbras wireless systems are tested to the highest standards for reliability. However, usage and installation scenarios require considerations:

• Transmitters/receivers may be affected by radio signals, natural interference, location, climatic issues, and other adversities impacting data transmission, regardless of frequency or technology, due to varying transmission mediums.
• Devices have internal processing time; data is received after this period.
• Wireless devices require regular testing to identify interference sources and protect against failures.

² The maximum range between the AMT 8000 alarm center and the PGM 8000 expander is up to 600 m with direct line of sight in an open field.

3. Features

• Low battery indication.
• Long battery life.
• Easy installation.
• Registration key.
• Tamper protection key.
• Two power options: AC 100/240 Vac ~ 50-60 Hz or DC: 12 Vdc to 24 Vdc.
• 1 internal 3 Vdc (CR2032) battery.
• Transmission frequency 915 MHz - 928 MHz.
• Protection against malicious signals.
• Encryption for data transmission between devices.

4. Registration at the Center Unit

To register the PGM expander with the alarm center:

1. Press the synchronization button on the center unit.
2. Press the button on the back of the expander (remove the product from its mounting bracket to access it).

Check the LED on the front of the expander:

• Green flashing: Successful registration.
• Orange flashing: Signal is intermittent or weak.
• Red flashing: Fault occurred; repeat the process.

The expander will be addressed according to the sequence of registration, respecting the limit of 16 devices of this type per center unit.

To check RF signal range: Press the sync button. Green LED indicates correct communication, orange indicates intermittent/weak communication, and red indicates no communication.

For registering other expanders/accessories via keyboard commands or for more information/configurations, refer to the AMT 8000 Alarm Center's complete manual.

Note: Perform the registration process safely, as the alarm center is energized.

5. Installation

The PGM 8000 expander includes a base for fixing to various surfaces like walls. To detach the expander from its base, slide it upwards. To reattach, follow the base's markings.

Fix the base using screws or double-sided tapes (sold separately) onto the desired surface. Arrange the installation wires as shown in the illustration, then fit the expander onto the base. Ensure both the base and the expander are securely fixed.

Diagram Description: The illustration shows the expander's base with a bracket for surface fixing and an output location for installation wires.

Note: Screws, double-sided tape, and other accessories are not included and must be purchased separately.

6. Battery / DC Supply / AC Power / Relay Drive

The PGM 8000 expander has an internal 3 Vdc CR2032 non-rechargeable battery. This battery powers the unit during AC/DC power outages to maintain communication with the center unit; however, the PGM output is deactivated during power loss. The battery connector is internal and not user-accessible for replacement.

The main power is supplied via an AC 100/240 Vac power supply or a 12 Vdc to 24 Vdc source (not included). Connect the power to the indicated locations and the device to be operated as shown.

Diagram Description: The diagram illustrates the PGM 8000 expander's connections. It shows terminals for AC input (110-250 Vac), DC input (12 Vdc or 24 Vdc), and the PGM output (NA, COM, NF). Connections are shown to a power supply and the device to be triggered. The diagram also indicates the location of the synchronization and reset buttons.

Notes:

• The predicted battery life is 3 to 5 years, which can be affected by the availability of DC and/or AC power.
• Power consumption when connected to mains:
  • Activated relay: 0.013 A
  • Deactivated relay: 0.010 A

7. Operation

The PGM extender is programmable and can trigger various devices such as electric locks, spotlights, auxiliary sirens, buzzers, or almost any electrical device. The PGM output activates upon programmed events and can operate in several modes:

• External triggering
• Password entry
• System activation
• System deactivation
• Medical emergency
• Failure to communicate event
• Phone line failure
• Siren problem
• Panic triggering
• Panic silent triggering
• Fire
• Zone 1 opening
• By remote control
• By time

After an event is restored, the PGM output deactivates. For more information and configurations, refer to the AMT 8000 Alarm Center manual.

8. Homologation

Anatel Homologation Number: 05326-18-00160

This equipment is authorized and does not cause harmful interference to duly authorized systems. The Anatel approval number is available on the product label. For inquiries, visit sistemas.anatel.gov.br/sch.

Warranty Term

This warranty is subject to the following conditions:

1. Intelbras provides a one (1) year warranty against manufacturing defects (90 days legal + 9 months contractual), counted from the purchase date shown on the invoice. This warranty includes the exchange of defective products. Costs for flaws due to inappropriate use are borne by the consumer.
2. Product installation must follow the manual. If professional installation is required, costs are not included.
3. Report defects immediately to the nearest Authorized Service. Unauthorized repairs void the warranty.
4. Home care requests may incur technical visit fees. Product withdrawal for service is at the consumer's expense.
5. The warranty is void if:
   • Defects are not manufacturing-related but caused by the consumer or third parties.
   • Damage results from accidents, claims, natural events (lightning, floods), humidity, voltage fluctuations, incorrect installation/use, or normal wear and tear.
   • The product is affected by chemicals, electromagnetic fields, electricity, or animals.
   • The serial number is tampered with or erased.
   • The device has been tampered with.
6. This warranty does not cover data loss; regular data backup is recommended.
7. Intelbras is not responsible for product installation or attempts of fraud/sabotage. Keep software updated and ensure network protection. The equipment is guaranteed under normal use conditions but may be affected by external fraud attempts.
8. The product has an internal battery. Dispose of batteries responsibly at authorized centers or Green Eletron collection points.

Intelbras S/A reserves the right to change product specifications without prior notice. Manufacturing process is not covered by ISO 14001 requirements. All images are illustrative.