Visa Lighting POSH Series Luminaires Installation Instructions
Manufacturer: Visa Lighting
Address: 1717 West Civic Drive, Milwaukee, WI 53209
Contact: 414-354-6600
Models Covered: CB5518, CB5519, CB5520, CB5521, CB5522, CB5523
Fixture Family: POSH
Overview
This document provides installation instructions for the POSH Series Luminaires manufactured by Visa Lighting. It covers various mounting configurations to ensure proper installation of these fixtures.
Sheet 2: Standard Install
Diagram shows a linear luminaire (HOUSING, LENS) mounted directly to a wall or junction box using MOUNTING BRACKETS secured by hardware (not supplied). The fixture attaches to the brackets via two MOUNTING SET SCREWS. A FLEXIBLE CONDUIT is shown connecting to the fixture. The fixture depth off the wall is noted as 4 inches.
Mounting Centers for Standard Install (4" Depth)
| Fixture Number | Mounting Center |
|---|---|
| CB5518 | 26-1/32" |
| CB5520 | 38-1/32" |
| CB5522 | 50-1/32" |
Installation Steps:
- Secure mounting brackets to the wall or junction box (JBC option) at the specified mounting center locations using hardware provided by others. Note that the mounting may differ based on the specific fixture or option ordered.
- Make wire connections. If the fixture is mounted directly to the wall, connections should be made within the fixture ends. Otherwise, make connections inside the junction box (JBC option).
- Slide the fixture over the mounting plates and tighten the mounting set screws to secure it.
Sheet 3: Install with Spacer Block
Diagram illustrates installation using a SPACER BLOCK. The setup is similar to the standard install, with MOUNTING BRACKETS attached to the surface. A SPACER BLOCK is placed between the MOUNTING BRACKET and the fixture's HOUSING, increasing the distance from the mounting surface. The fixture depth off the wall is noted as 4-5/8 inches.
Mounting Centers for Install with Spacer Block (4-5/8" Depth)
| Fixture Number | Mounting Center |
|---|---|
| CB5519 | 26-1/32" |
| CB5521 | 38-1/32" |
| CB5523 | 50-1/32" |
Installation Steps:
- Secure mounting brackets to the wall or junction box (JBC option) at the specified mounting center locations using hardware provided by others. Note that the mounting may differ based on the specific fixture or option ordered.
- Make wire connections. If the fixture is mounted directly to the wall, connections should be made within the fixture ends. Otherwise, make connections inside the junction box (JBC option).
- Slide the fixture over the mounting plates and tighten the mounting set screws to secure it.
Sheet 4: Install with Jbox Cover
Diagram details installation using a junction box (J-BOX) and a J-BOX COVER. It shows the MOUNTING BRACKET attaching to the J-BOX. The JUNCTION BOX COVER MOUNTING BRACKET W/ STUDS is also shown, indicating it's required for this option. The fixture (HOUSING, LENS) attaches to the mounting bracket via MOUNTING SET SCREWS, and MOUNTING BRACKET NUTS secure the bracket to the J-BOX. The fixture depth off the wall is noted as 4 inches.
Mounting Centers for Install with Jbox Cover (4" Depth)
| Fixture Number | Mounting Center |
|---|---|
| CB5518 | 26-1/32" |
| CB5520 | 38-1/32" |
| CB5522 | 50-1/32" |
Installation Steps:
- Secure mounting brackets to the wall or junction box (JBC option) at the specified mounting center locations using hardware provided by others. Note that the mounting may differ based on the specific fixture or option ordered.
- Make wire connections. If the fixture is mounted directly to the wall, connections should be made within the fixture ends. Otherwise, make connections inside the junction box (JBC option).
- Slide the fixture over the mounting plates and tighten the mounting set screws to secure it.
Sheet 5: Install with Jbox Cover and Spacer Block
Diagram combines elements for installation with a J-BOX, J-BOX COVER, and SPACER BLOCK. It shows the MOUNTING BRACKET attaching to the J-BOX, with the SPACER BLOCK positioned between the bracket and the J-BOX COVER. The JUNCTION BOX COVER MOUNTING BRACKET W/ STUDS is also shown. The fixture (HOUSING ASSEMBLY, LENS) attaches to the mounting bracket via MOUNTING SET SCREWS, and MOUNTING BRACKET NUTS secure the bracket. The fixture depth off the wall is noted as 4-5/8 inches.
Mounting Centers for Install with Jbox Cover and Spacer Block (4-5/8" Depth)
| Fixture Number | Mounting Center |
|---|---|
| CB5519 | 26-1/32" |
| CB5521 | 38-1/32" |
| CB5523 | 50-1/32" |
Installation Steps:
- Secure mounting brackets to the wall or junction box (JBC option) at the specified mounting center locations using hardware provided by others. Note that the mounting may differ based on the specific fixture or option ordered.
- Make wire connections. If the fixture is mounted directly to the wall, connections should be made within the fixture ends. Otherwise, make connections inside the junction box (JBC option).
- Slide the fixture over the mounting plates and tighten the mounting set screws to secure it.
General Safety Precautions
When using electrical equipment, basic safety precautions should always be followed, including the following:
- Read all instructions carefully before installing and save for future use.
- Make sure all connections are in accordance with the National Electrical Code and local regulations.
- To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture.
- Service should be performed by qualified personnel.
- These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.
