EverStart Maxx BC4WE 4A Waterproof Battery Charger/Maintainer

Features

The EverStart Maxx BC4WE is a 4A waterproof battery charger and maintainer. Key features include:

• AC Power Cord
• Charging / Charged LED
• Reverse Polarity LED
• Battery Clamps
• Double Barrel Charger Connector (connects to terminal rings, clamps)
• Battery Terminal Rings
• Magnetic Discs (exposed to show detail)
• Mounting Bracket
• Hanging Hook

Safety Guidelines / Definitions

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

CAUTION (without safety alert symbol): Indicates a potentially hazardous situation which, if not avoided, may result in property damage.

Risk of Unsafe Operation: Basic safety precautions should always be followed. Improper operation, maintenance, or modification can lead to serious injury and property damage. This product should not be modified or used for any application other than its intended purpose. Read and understand all warnings and operating instructions before using.

Read All Instructions

WARNING: Read and understand this instruction manual before using this unit. Failure to follow all instructions may result in electric shock, fire, and/or serious injury.

Important Safety Instructions

General Safety Warnings and Instructions

• Keep children away. This is not a toy.
• Store indoors in a dry, locked-up place, out of reach of children.
• Unplug the battery charger when not in use.

Specific Safety Instructions for Power Cords

• Do not abuse the cord. Never carry the appliance by the cord or yank it to disconnect from the receptacle. Keep the cord from heat, oil, and sharp edges. Pull by the plug rather than the cord when unplugging.
• Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuits or outlets used.
• Extension Cords: Use of an improper extension cord can result in fire and electric shock. Ensure the extension cord is in good condition and heavy enough to carry the current. Refer to the table for recommended AWG sizes based on cord length and amperage.
• Power Cord Safety: This appliance has a polarized plug. It will fit into a polarized outlet only one way. If it does not fit fully, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

Specific Safety Instructions for Battery Chargers

• This unit is designed for household use only.
• Use of accessories and attachments not recommended by the manufacturer could be hazardous.
• Stay alert. Use common sense. Do not operate when tired or impaired.
• Check for damaged parts. Damaged parts should be repaired or replaced by the manufacturer before further use.
• Do not operate the battery charger near flammable liquids or in gaseous or explosive atmospheres.
• Do not operate if the unit has been dropped or damaged. Return it to the manufacturer for repair.
• WARNING - Burst Hazard: Do not use for charging dry-cell batteries. Use only for charging/boosting 12-volt LEAD-ACID batteries. Never attempt to charge non-rechargeable batteries.
• WARNING - Risk of Explosive Gases: Batteries generate explosive gases during normal operation. Always read and follow instructions exactly. Review cautionary markings on products and engines. This equipment produces arcs or sparks; if used in a garage or enclosed area, the unit MUST be placed not less than 18 inches (46 cm) above the floor.
• WARNING - To Reduce the Risk of Fire: Do not operate near flammable materials, fumes, or gases. Do not expose to extreme heat or flames.
• CAUTION - To Reduce the Risk of Injury or Property Damage: This charger is not designed for every make, manufacturer, or model of engine. Use only with 12-volt systems. NEVER attempt to charge a frozen battery. Do not charge the battery while the engine is operating. Stay clear of fan blades, belts, pulleys, and other parts that can cause injury.

Specific Safety Instructions for Using the Unit in Wet Environments

The housing is rated IP67 (dust-proof and waterproof). However:

• Never submerge the unit in water deeper than 1 meter for longer than 30 minutes or in temperatures outside 41°F-104°F (5°C-40°C).
• Never submerge the unit if the AC or DC cord bushing (insulation) is not intact.
• Do not allow clamps to be exposed to the elements for long periods or submerge them.

First Aid

• SKIN: If battery acid contacts skin, rinse immediately with water, then wash thoroughly with soap and water. Seek medical attention if redness, pain, or irritation occurs.
• EYES: If battery acid contacts eyes, flush eyes immediately for at least 15 minutes and seek immediate medical attention.

Preparing to Charge

1. Ensure the area around the battery is well-ventilated.
2. Remove the battery from confined areas before charging.
3. If removing the battery, disconnect the grounded terminal first. Ensure all vehicle accessories are off.
4. Clean battery terminals, avoiding contact with corrosive material.
5. Add distilled water to each cell if necessary, following battery manufacturer's instructions. Do not overfill.
6. Follow all battery manufacturer's specific precautions.
7. Determine the battery voltage (unit is for 12-volt batteries only).

Charger Location

• Locate the charger as far from the battery as cables permit.
• Never place the charger directly above the battery being charged.
• Do not set a battery on top of the charger.
• Never allow battery acid to drip on the charger.
• Charge at temperatures between freezing and 104°F (40°C).
• Never operate the charger in a closed area or restrict ventilation.
• Marine batteries must be removed and charged on shore.

Connection Precautions

• Never allow clamps or ring terminals to touch each other.
• Attach clamps to the battery and chassis as indicated in the appropriate section.

Charging a Battery Installed in a Vehicle

WARNING: A spark near the battery may cause an explosion.

1. Position AC and clamp cords to reduce risk of damage by moving parts.
2. Stay clear of fan blades, belts, pulleys, and other moving parts.
3. Check battery post polarity (Positive/POS/+ usually larger diameter than Negative/NEG/-).
4. Determine which post is grounded to the chassis.
5. For negative-grounded vehicles: Connect the POSITIVE (RED) clamp to the POSITIVE (un-grounded) battery post. Connect the NEGATIVE (BLACK) clamp to the vehicle chassis or engine block away from the battery (connect to heavy gauge metal part).
6. For positive-grounded vehicles: Connect the NEGATIVE (BLACK) clamp to the NEGATIVE (un-grounded) battery post. Connect the POSITIVE (RED) clamp to the vehicle chassis or engine block away from the battery.
7. Refer to operating instructions for charge duration.
8. When disconnecting, disconnect AC power first, then remove the clamp from the chassis, and finally remove the clamp from the battery terminal.

Charging a Battery Removed from a Vehicle

WARNING: A spark near the battery may cause an explosion.

1. Check battery post polarity.
2. Attach a 24-inch (minimum length) AWG #6 insulated battery cable to the NEGATIVE battery post.
3. Connect the POSITIVE (RED) battery clamp to the POSITIVE battery post.
4. Connect the NEGATIVE (BLACK) charger clamp to the free end of the battery cable connected to the negative terminal. Stand as far back from the battery as possible and do not face the battery when making the final connection.

Note: Marine batteries must be removed and charged on shore. This unit is not designed for charging on board.

When disconnecting, do so in reverse sequence of connecting and break the first connection while as far away from the battery as practical.

Setting Up the Unit

Mounting the Battery Charger

The charger can be mounted on a flat surface using the mounting brackets.

CAUTION: Ensure all instructions are understood and followed. Disconnect the charger from power and battery before mounting. Do not hang anything additional on the charger.

1. Position the unit on a flat wall surface near a functioning AC outlet. Ensure the surface is flat and free of obstruction.
2. Use an 8/32-inch wood screw through each mounting bracket. Do not over-tighten.

WARNING: Do not put screws through the plastic housing, as this will permanently damage the unit and create an electrical hazard.

To Mount the Unit Using the Magnetic Discs

The magnetic discs on the bottom allow positioning on any flat, secure metallic surface.

Using the Hanging Hook

The hanging hook can be used for convenient positioning.

CAUTION: Do not shake the charger or the surface it is attached to. Ensure the charger is securely hung or attached. Only use the hanging hook or magnetic discs for positioning. They are not intended to support additional weight.

Operating Instructions

WARNING: Always disconnect the AC plug from the outlet first before disconnecting the charger from the battery.

Ensure all instructions and precautions are understood and observed.

Charging Using the Supplied Battery Clips

1. Ensure the battery charger is unplugged and not connected to a battery.
2. Insert the double barrel tip of the battery clamp cable into the unit's Double Barrel Charger Connector.
3. Connect the battery clamps to the battery and position the unit as far away from the battery as possible, following the "Preparing to Charge" section.
4. Insert the AC plug into a standard 120-volt, 60Hz North American outlet. The Charging/Charged LED will flash green.

Notes: If the Reverse Polarity LED lights, unplug the charger, remove clamps, and reconnect properly. If the Charging/Charged LED does not light, check connections and AC outlet. If connections are good, the battery may be faulty.

When the Charging/Charged LED lights solid, charging is complete. Disconnect AC power first, then the chassis clamp, then the battery clamp.

Connecting and Charging with the Terminal Rings

Connecting:

1. Remove nuts from battery post connectors.
2. Position the RED terminal ring on the POSITIVE battery post connector bolt.
3. Position the BLACK terminal ring on the NEGATIVE post connector; then replace the nuts.

IMPORTANT: If there are connection problems, contact Customer Service for assistance.

Charging:

1. Ensure the battery charger is unplugged and not connected to a battery.
2. With terminal rings properly connected, connect the terminal ring connector to the unit's Double Barrel Charger Connector and position the unit as far away from the battery as possible.
3. Insert the AC plug into a standard 120-volt, 60Hz North American outlet. The Charging/Charged LED will flash green.

Notes: If the Reverse Polarity LED lights, disconnect the charger, disconnect terminal rings, and reconnect properly. If the Charging/Charged LED does not light, check connections and AC outlet. If connections are good, the battery may be faulty.

When the Charging/Charged LED lights solid, charging is complete. Disconnect the AC cord, then remove the terminal rings from the battery posts.

Care and Maintenance

Cleaning and Storage

• Unplug the battery charger before any maintenance or cleaning.
• Store the unit in a clean, dry, cool place when not in use.
• Clean the unit casing and cords with a dry or slightly damp cloth. Ensure the unit is disconnected from the battery and power source before cleaning.
• Coil charger cords loosely for storage to prevent damage. Do not wrap them tightly around the unit.

CAUTION: Do not use the charger if cables or clamps are damaged; call Technical Support. This unit contains no user-serviceable parts. Do not open the unit; return to the manufacturer for service. Opening the unit will void the warranty.

Troubleshooting

Accessories

Recommended accessories may be available from the manufacturer. Contact the manufacturer at 1-877-571-2391 for assistance.

WARNING: Use of any accessory not recommended by the manufacturer could be hazardous.

Service Information

For technical advice, repair, or genuine factory replacement parts, contact the manufacturer at 1-877-571-2391.

Two-Year Limited Warranty

The manufacturer warrants this product against defects in materials and workmanship for TWO (2) YEARS from the date of retail purchase by the original end-user purchaser.

If a defect exists and a valid claim is received within the Warranty Period, the defective product may be replaced or repaired at the manufacturer's option. Proof of purchase may be required.

This warranty does not apply to accessories, bulbs, fuses, and batteries; defects resulting from normal wear and tear, accidents; damages sustained during shipping; alterations; unauthorized use or repair; neglect, misuse, abuse; and failure to follow instructions for care and maintenance.

This warranty gives you specific legal rights, and you may have other rights which vary from state to state or province to province. This product is not intended for commercial use.

Appendix

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If equipment causes harmful interference to radio or television reception, the user is encouraged to try to correct the interference by:

• Reorienting or relocating the receiving antenna.
• Increasing the separation between the equipment and receiver.
• Connecting the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consulting the dealer or an experienced radio/TV technician for help.

Changes or modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment.

Specifications

Input: 120V AC, 60Hz, 0.9A

Output: 12V DC, 4A

Imported by Baccus Global LLC, 621 NW 53rd St., Suite 450, Boca Raton, FL 33487

www.Baccusglobal.com

1-877-571-2391

RD032620

Resumen en Español

Cargador / Mantenidor de Batería EverStart Maxx BC4WE 4A Impermeable

Este manual proporciona instrucciones de seguridad, operación, solución de problemas y garantía para el cargador/mantenedor de batería EverStart Maxx BC4WE.

Características Principales:

• Cargador y mantenedor de batería de 4A, impermeable.
• Diseñado para baterías de plomo-ácido de 12V.
• Incluye pinzas de batería y anillos terminales para conexión.
• Indicadores LED para estado de carga y polaridad inversa.
• Diseño robusto y seguro para uso doméstico.

Instrucciones de Seguridad Importantes:

• Leer todas las instrucciones antes de usar.
• Evitar el contacto con ácido de batería y gases explosivos.
• No exponer a líquidos o atmósferas inflamables.
• Asegurar ventilación adecuada durante la carga.
• No intentar cargar baterías no recargables o congeladas.
• Seguir las precauciones específicas para el uso en ambientes húmedos.

Operación:

• Conectar las pinzas o anillos terminales a la batería según las instrucciones.
• Conectar el cable de alimentación a una toma de corriente de 120V AC, 60Hz.
• El LED de carga indicará el estado del proceso.

Cuidado y Mantenimiento:

• Limpiar las pinzas y el exterior de la unidad con un paño seco.
• Almacenar en un lugar limpio, seco y fresco.
• Enrollar los cables de forma holgada para evitar daños.

Solución de Problemas:

• Verificar conexiones, polaridad y fuente de alimentación si la unidad no carga.
• Si la batería tiene menos de 2V, puede que no se recargue.

Garantía:

• Garantía limitada de dos años contra defectos de materiales y mano de obra.

Información de Contacto:

• Servicio al Cliente: 1-877-571-2391
• Sitio Web: www.Baccusglobal.com