ZKTeco | Biometrics and Computer Vision
User Guide for ZKTeco models including: G4, Multi-Biometric Identification Terminal
QUICK START GUIDE Applicable Model: G4 Version:V1.0 Date: Oct 2018 Safety Precautions Before installation, please read the following precautions carefully
File Info : application/pdf, 1 Pages, 880.08KB
DocumentDocumentQUICK START GUIDE Applicable Model: G4 Version: V1.0 Date: Oct 2018 Safety Precautions Before installation, please read the following precautions carefully to prevent risks and dangers to this product, users and any other person. Do not expose to direct sunlight, water, dust and soot. Do not place any magnetic objects near the product. Magnetic objects such as magnets, CRT, TV, monitors or speakers may damage the device. Do not place the device next to any heating equipment. Prevent water, drinks or chemicals leaking into the device. This product is not intended for use by children unless they are supervised. Do not drop or damage the device. Do not disassemble, repair or modify the device. Do not use the device for any purpose other than those specified. Remove dusts or dirts regularly. While cleaning, wipe dust off with a smooth cloth or towel instead of water. Contact your supplier in case of any problem! 1.55m User Registration 1) Recommended distance For users with height from 1.5m to 1.8m, the recommended device height is 1.55m. It can be adjusted and installed according to the users' average height. User Registration 3) Registration During registration, please adjust your position and keep your face inside the green frame. 1.55m 1.55m The recommended position The registration and verification position of the device should not be changed to avoid affecting the verification accuracy. If it is necessary to move the device, then move it horizontally and keep the vertical height same. 2) The recommended and not-recommended facial expressions: 8 7 6 5 4 3 2 1 ZK Building, Wuhe Road, Gangtou, Bantian, Buji Town, Longgang District, Shenzhen China 518129 Tel: +86 755-89602345 Fax: +86 755-89602394 www.zkteco.com Ethernet & Power Connection LAN Connection PC Power Connection 12V DC Adaptor Recommended power supply Rating of 12V and 3A To share the device's power with other devices, use a power supply with higher current ratings. 7 Menu Functions Enroll New User 1 Device Overview Front Side Visible light camera LED IR camera LED IR LED 7 Inch HD capacitive touch screen IC Card Reader Fingerprint sensor Speaker Bottom USB port Reset Button 4 Lock Relay Connection The system supports Normally Opened Lock and Normally Closed Lock. The diagrams shown hereafter represents Normally Closed Lock. Device not sharing power with the lock is shown below: Lock Power NC Lock FR107 DC12V SEN GND BUT NO COM NC +12V GND Device sharing power with the lock is shown below: NC Lock FR107 SEN GND BUT NO COM NC DC12V +12V GND 8 Menu Functions Access Settings 2 Device Overview Product PIN Diagram +12V GND IWD0 IWD1 WD0 WD1 Wiegand In Wiegand Power Out Output NO COM NC +12V GND Power In Lock SEN GND BUT NO COM NC Lock Button Sensor Tamper Switch Ethernet port Power port Product Dimensions 10.4in (264.0mm) 4.4in (112.0mm) 2.0in (51.0mm) 5 7.2in (182.8mm) 3.1in (79.5mm) Connecting Other Devices Button & Sensor Connection Alarm Connection Door Sensor No Touch EXIT Exit Button SEN GND BUT NO COM NC Wiegand Connection Alarm power Alarm NO COM NC Wiegand Reader +12V GND IWD0 IWD1 WD0 WD1 Wiegand Device Wiegand In Port 9 Menu Functions Record Search 3 Product Installation Mounting the device on wall 1 1.2m 7 8 Mounting Hole Mounting Hole Mounting Hole G4 Mounting template (Only for your reference) Mounting Hole Wiring Hole Mounting Hole 9 10 Mounting Hole 11 Mounting Hole Mounting Hole Instruction for using this template: 12 Before installing the device, please paste this template onto the desired installation place, and then drill holes and lay cables according to the marks on the template. 13 Baseline 14 Recommended height from the ground is 1.2m and can be adjusted according to the personnel average height. 15 2 3 4 Paste the mounting template sticker onto the wall, and drill holes according to it. Fix the back plate to the wall with wall mounting screws. Attach the device to the back plate. Fasten the device to the back plate with a security screw. 6 Standalone Installation Option A Option B PC WAN TCP/IP WiFi PC SWITCH Door Sensor Lock Alarm Exit Button 10 Menu Functions & Troubleshooting Date and Time Settings Go to Main Menu > Access Settings > Access control parameters to enter Access control parameters setting interface. Network Settings Go to Main Menu > Employee Management > > New Employee > Enroll verification mode. Settings include entering Employee Name, ID, choosing User Role (Normal User is not authorized to operate the menu options of the device. Super Admin can operate all the menu options of the device), registering Fingerprint, Face Registration, Enroll Badge Number (ID and Mifare card are optional), and setting Password. 11 Go to Main Menu > System Settings > Network Settings, set the IP Address. The device will communicate with PC via the Ethernet parameters. Using Cloud Service Settings sets Server Address and Server port according to the server. 12 View records in the device: Go to Main Menu > Record Search > Att Log enter Name or Employee ID (if user ID field is left blank, records of all users will be displayed) > select Time Range > press OK, the corresponding attendance logs will be displayed. View records on computer: Go to Main Menu> USB disk Management > USB disk Download. Insert the USB disk correctly and download the data to the USB drive, then copy this data from the USB drive to your PC. The downloaded data filename will be "Device Serial Number.dat", you can open and view it. Go to Main Menu > System Settings > Date and Time, to enter Date and Time setting interface. Troubleshooting 1. Fingerprint cannot be detected or it takes too long. 2. Failed to gain access after successful verification. 3. Door does not open after successful verification. 13 14