VonHaus 3500243 Bicycle Repair Stand

Important Information

ℹ️ Please read all instructions carefully before use and retain for future reference.

Maximum Load Capacity: 25Kg / 55lb

Estimated Assembly Time: 30 minutes

Safety Precautions

• ⚠️ Do not use power tools for assembly.
• ⚠️ Do not climb on the product.
• ⚠️ Do not jump on the product.
• ℹ️ Re-tighten fixings every 6 months.
• ℹ️ When relocating the item, never drag it. This may cause damage to fixtures and make the item unstable. Disassemble where appropriate.
• This product is not intended for indoor use, as a climbing structure, or as a toy.
• Children should be supervised to ensure they do not play with the product.
• Assemble on solid and even ground.
• Only use in an upright, stable position.
• ⚠️ Do not overload the product, as this may result in damage or personal injury.
• ℹ️ The assembly pack may contain small parts which can pose a choking hazard to children and pets.

Cleaning and Maintenance

Do not clean the product with abrasive cloths or chemicals. Solvents or detergents can cause surface damage.

Periodically check and re-tighten fittings where necessary. Re-tighten all fittings after the first week following assembly.

To clean, use a sponge with warm water, a soft cloth, and mild detergent.

If any components are missing, contact customer services at support@domu.co.uk. Do not proceed with assembly if parts are missing.

Assembly Instructions

Parts List

• 1. Top Pole (64cm/640mm)
• 2. Bottom Pole (84cm/840mm)
• 3. Centre Leg (74cm/740mm)
• 4. Leg (64cm/640mm)
• 5. Balance Bar
• 6. M5x35mm Screw
• 7. M5x15mm Screw
• 8. M4x25mm Screw
• 9. M4 Nut
• 10. Base Connector
• 11. Head Clamp Connector
• 12. Pole Connector
• 13. Head Clamp
• 14. Balance Bar Straps
• 15. Feet
• 16. Accessory Tray
• 17. Hex Key 4mm
• 18. Hex Key 5mm

Assembly Steps

Step 1: Assemble the Base and Legs

Attach the three Legs (4) to the Base Connector (10) using M5x15mm screws (7) and M4 nuts (9). Secure the Legs by tightening the screws with the Hex Key (17). Fit the Feet (15) onto the bottom of each Leg (4).

Step 2: Attach the Bottom Pole

Connect the Bottom Pole (2) to the central part of the assembled base.

Step 3: Attach the Top Pole and Head Clamp Connector

Insert the Pole Connector (12) into the Top Pole (1) and attach it to the Bottom Pole (2). Connect the Head Clamp Connector (11) to the Top Pole (1).

Step 4: Attach the Accessory Tray

Attach the Accessory Tray (16) to the vertical pole using the provided clamp (6) and M4 nut (9), tightening with the Hex Key (17).

Step 5: Attach and Adjust the Head Clamp

Attach the Head Clamp (13) to the Head Clamp Connector (11) on the Top Pole (1). Adjust the clamp to fit your bicycle frame by loosening and tightening the screws. Use the 'Lift to release' mechanism to open the clamp.

Support, Warranty, and Disposal

Customer Service: If you require assistance, please contact support@domu.co.uk.

Warranty: Register your product at www.vonhaus.com/warranty. Please retain your proof of purchase. The warranty is subject to terms and conditions outlined in the manual.

Disposal: Please recycle where facilities exist. Check with your local authority for recycling advice.

Copyright: All material in this manual is copyrighted by DOMU Brands.

Thank you for purchasing your VonHaus product.