Ruvati Installation Guide: Undermount Workstation Sink
Model Numbers: RVH183001LM, RVH185841LM
Care and Maintenance
- Clean regularly with mild detergent and warm water.
- Always dry the sink after use and buff with a soft cloth to prevent limescale buildup.
- Clean the sink once or twice a month using a non-abrasive cleanser like Barkeeper's Friend, scrubbing in the direction of the natural grain.
- Never let soap or cleaners dry on the sink surface, as additives can affect the finish.
- Avoid bleach solutions, as they are harmful to stainless steel and can cause pitting.
- Never use steel wool, as it can damage the sink's surface and cause discoloration.
- Minor scratching is normal and can often be removed with a proprietary stainless steel cleaner.
- Using rinse grids can reduce scratches on the sink bottom.
Ruvati Limited Lifetime Warranty
Ruvati sinks are manufactured to high standards and carry a limited lifetime warranty for residential use. For warranty claims, a copy of the proof of purchase is required. The warranty covers defects in materials or workmanship for the original purchaser and does not include shipping or labor costs. This warranty applies to residential installations only. Ruvati reserves the right to examine the product before replacement. If an identical product is unavailable, a similar product may be substituted. Accessories like rinse grids, cutting boards, and strainers are not covered.
This warranty does not cover damage from failure to follow care and maintenance instructions, normal wear and tear, scratches, accidental damage, improper use, or installation faults. Incidental or consequential damages are excluded. Some states may have different provisions regarding implied warranties and limitations.
Register your product at: www.ruvati.com/register
Ruvati Contact Information
Address: 2705 Meister Pl, Round Rock, TX 78664
USA Phone: 1.855.478.8284
Email: support@ruvati.com
Attention Installer
Please read this guide carefully before installation. Keep the sink covered until construction is complete to protect it from dirt and dust. Professional installation is recommended. Sink edges can be sharp; wear cut-resistant gloves. Inspect the sink and contents upon delivery for any shipping damage or missing parts and contact Ruvati Support immediately. Templates are guides; ensure proper cutout. Ruvati is not responsible for improper installation or damages.
Follow all local plumbing and building codes.
Tools Required
- Plumbers Putty
- Drill with Depth Stop
- Sink Mounting Clips
- Silicon Caulk
- Phillips Head Screwdriver
- Jigsaw or Keyhole Saw
- Pencil
- Sink Cut-Out Template
Reveal
Proper alignment of the sink to the cutout is critical for a superior fit. Ruvati recommends a 1/4" reveal. DO NOT INSTALL WITH AN OVERHANG.
- 1/4" Reveal (Recommended): The countertop edge sits approximately 1/4” back from the sink edge, exposing the sink rim.
- Flush Fit (OK): The countertop meets the sink edge, fitting flush with the sink bowl.
- Overhang (Don't): The countertop extends over the sink edge on all sides.
Instructions
- Place the template on the countertop, ensuring proper clearance from the cabinet.
- Trace the template line. Adjust the line based on your desired sink reveal and cut along the line.
- Turn the countertop upside down. Mark evenly-spaced positions for mounting clips (3 for longer sides, 2 for shorter sides).
- Drill holes for anchors as per countertop manufacturer instructions. Use a 3/8" drill bit with a 1½" depth stop. Secure anchors and attach mounting clips with screws.
- Clean the countertop underside and sink rim. Apply silicone caulk evenly around the sink rim.
- Position the sink over the countertop opening. Tighten screws until mounting clips are snug.
- Check sink alignment and adjust if necessary.
- Tighten clips evenly without overtightening. Remove excess silicone.
Rust Spots?
Ruvati sinks are made of T-304 stainless steel and cannot rust. Rust spots are typically caused by external iron particles. Clean these spots with Barkeeper's Friend and a soft sponge, scrubbing in the direction of the grain. Use a toothbrush for corners. Rinse thoroughly.
