Deaf Bonce Apocalypse AAP-400.4D

1. Introduction

Thank you for purchasing this Deaf Bonce product! Our company is committed to the creation of extremely loud sound systems with no loss of quality. To ensure proper use, please carefully read through this manual before using this product. It is especially important that you read and observe cautions in this manual. Please keep the manual in a safe and accessible place for future reference.

2. Safety Instructions

1. Make sure that your vehicle has a 12V DC electrical system with negative grounding. Before installing the amplifier in cars, trucks or buses, check the battery voltage.
2. Check the state of on-board power supply of your vehicle, the battery and the alternator. When the engine is running, depending on the ambient temperature, the voltage to be outputted by the alternator must be within the range of 14 to 14.7 V. Open circuit voltage (OCV) of the battery must be within the range of 12.5 to 13 V. Make sure that the rated current of the alternator and the battery capacity is enough to provide increased consumption. For example, for the power of the amplifier 1000 W, the rated current of the alternator is required at the rate of 1000 W / 13 V = 77 amperes. A more powerful amplifier requires a more powerful alternator as well as an additional battery.
3. Do not place the amplifier in the engine compartment and also in the places exposed to water, moisture, dust or dirt.
4. Never stretch the cables outside of the car and near the moving parts of the car. This can lead to destruction of the insulating layer, short circuit and fire.
5. The amplifier should be installed in areas of the car where the temperature varies from 0 °C (32 °F) to 55 °C (131 °F). The amplifier should be in a place with a good air circulation. The horizontal position of the amplifier is the best way to install.
6. During the operation the amplifier may be heated up to 80 °C (176 °F). Before you touch it, make sure it is not overheated that may be dangerous.
7. To improve the cooling of the amplifier, it is recommended to clean periodically the heatsink from dust. When cleaning the heatsink strong solvents should not be used as they may damage the amplifier. Do not use compressed air, because solids can penetrate inside the amplifier. Cleanings best done with wet towels or cloth.
8. Make sure that the location of the amplifier does not violate the proper operation of mechanical and electrical devices of the vehicle.
9. Make sure that during the installation and connection of the battery, the power cables are not shorted.
10. When performing plumbing, drilling or cutting works with the car, make sure that there is no wiring, brake lines, fuel pipe or other structural elements under the place of work. Follow the safety rules! Use protective glasses and gloves.
11. To protect the wires use rubber gaskets if the wire passes through a hole in the plate, or other similar materials if it lies close to the parts exposed to heat.
12. Make sure that all the cables are fixed over the entire length. Also make sure that their outer protective shell is non-combustible. Use a clamping screw to secure the positive and negative cables next to the appropriate terminals of the amplifier.
13. Select a diameter of the power cable in accordance with the power of the amplifier and the recommendations provided here. Power cables are extremely important since they directly affect the system damping factor and sound quality. The cables to the battery must be in the copper crimp terminals pressed with the help of a hydraulic press, and well fixed to the battery terminals.
14. To avoid accidental damage, keep the amplifier in its original packaging prior to installation.
15. Use high-quality copper speaker and power cables.

CAUTION!!! High sound pressure can damage your health! Please use the common sense when controlling volume!

3. Typical Installation Sequence

1. Before installing the amplifier disconnect the battery from the electrical system.
2. To connect the amplifier it is necessary to stretch the power cable from the location of the battery to the place of installation of the amplifier. Select the power cable with the appropriate regulations in AWG (see Table: Selection of the diameter of the power cables)
3. Connect the power supply with the correct polarity. Connect all (+) terminals of the amplifier to the cables stretching from the positive terminal of the battery and all (-) terminals of the amplifier – to the cables stretching from the negative terminal of the battery.
4. Place the fuse holder for each positive cable within 40 cm from the positive terminal of the battery and connect one end of the power cable to the holder after connecting the other end to the amplifier. Do not install the fuse(s).
5. Route all signal cables next to each other and separately from the power cables.
6. Connect the wires of RCA input. The input signal power must be between 0.2 V and 6 V.
7. To connect the power wire supply is necessary to use special power cables.
8. Fasten the amplifier properly when installing it in the vehicle. If the component is disconnected during driving, it may cause serious damage to the passengers of the vehicle or another vehicle. It is not recommended to screw the amplifier directly to the metal it can lead to distorsions at the signal outputs.
9. After installation is complete, check the wiring of the system and make sure that all connections have been made correctly. Before installing the fuses, disconnect the positive lead from the battery and then install the fuse in the fuse holder. Using the light bulb 12 V 21 W, connect the positive lead to one contact of the bulb and the other contact of the bulb to the positive terminal of the battery. When properly connected, the bulb must briefly light up and go out. Now you may connect the positive lead to the (+) of the battery. If the light does not go out, then something is wrong. This will prevent damage to the amplifier in case of reverse polarity and unwanted sparks when connecting. Install the rest of the fuses.
10. To activate the amplifier, it is necessary to apply the positive potential of 12 volts to the control input of the amplifier (REM IN) through a switch or a corresponding control output (REMOTE OUT ) with the head unit (HU).
11. LED indicator on front of the amplifier turns blue to indicate that the amplifier is turned on. If the indicator does not light up see chapter "Possible faults and their solutions" for more information.
12. The sound level is calibrated by adjusting the volume of the source up to 3/4 of its maximum level. Then, adjust the sensitivity level of the amplifier up until you hear distortions.

4. Selection of the Diameter of Power Cables and Speaker Cables

Selection of the diameter of the power cables

Use the table below to select the desired diameter based on the length and the current consumption. Note that cable length also influences the required diameter; longer cables may require a larger diameter.

Selection of the diameter of the speaker cables

Use the table below to select the desired diameter based on the length and the power consumption. Note that cable length also influences the required size; longer cables may require a larger size.

5. Wiring Diagrams

Standard wiring diagram of four-channel amplifier to two speakers, to one subwoofer and to battery

Diagram showing a four-channel amplifier connected to two speakers and one subwoofer. Speaker outputs CH1/CH2 are connected to the first speaker, CH3/CH4 to the second speaker, and CH1/CH2 (bridged) to the subwoofer. Power input (+12V, GND, REM IN) is shown connected to the battery via a fuse holder (fuse not installed yet). RCA inputs are shown for signal connection.

Caution!!! The minimum permissible connection load impedance at single channel is 1 ohm. For amplifier AAP-400.4D the operating voltage is 9-15V.

Standard wiring diagram of four-channel amplifier to four speakers

Diagram showing a four-channel amplifier connected to four separate speakers. Speaker outputs CH1, CH2, CH3, and CH4 are connected to individual speakers.

Caution!!! The minimum permissible connection load impedance at single channel is 1 ohm. For amplifier AAP-400.4D the operating voltage is 9-15V.

Standard wiring diagram of four-channel amplifier to head unit

Diagram showing RCA cables connecting the Head Unit (HU) output to the amplifier's INPUT terminals.

Application of connectors and controls

• 1. Input: RCA jacks for signal input.
• 2. HPF: High Pass Filter (15 Hz – 6 kHz at 12 dB/Oct).
• 3. LPF: Low Pass Filter (50 Hz – 6 kHz at 12 dB/Oct).
• 4. GAIN: Input signal level adjustment (0.2 V – 6 V).
• 5. CROSSOVER: Built-in filter mode selection (HPF, FLAT, LPF / BP).
• 6. POWER: Blue LED indicator for operation.
• 7. CLIP: Yellow LED indicator for clipping.
• 8. PROTECT: Red LED indicator for protection.
• 9. BASS BOOST: Bass level adjustment (0 – 12 dB).
• 10. SPEAKERS OUTPUTS: Speaker terminal connections.

6. Connection Methods

The minimum permissible load impedance at the output of the amplifier is 1 ohm.

Speakers Wiring Diagrams

Serial connection of the speakers

Diagrams illustrating serial connections of speakers and corresponding total impedance tables:

• 2 Speakers (4 Ohm voice coils): Total impedance 8 Ohm.
• 2 Speakers (8 Ohm voice coils): Total impedance 16 Ohm.
• 3 Speakers (4 Ohm voice coils): Total impedance 12 Ohm.
• 3 Speakers (8 Ohm voice coils): Total impedance 24 Ohm.
• 4 Speakers (4 Ohm voice coils): Total impedance 16 Ohm.
• 4 Speakers (8 Ohm voice coils): Total impedance 32 Ohm.

Parallel connection of the speakers

Diagrams illustrating parallel connections of speakers and corresponding total impedance tables:

• 2 Speakers (4 Ohm voice coils): Total impedance 2 Ohm.
• 2 Speakers (8 Ohm voice coils): Total impedance 4 Ohm.
• 3 Speakers (4 Ohm voice coils): Total impedance 1.33 Ohm.
• 3 Speakers (8 Ohm voice coils): Total impedance 2.66 Ohm.
• 4 Speakers (4 Ohm voice coils): Total impedance 1 Ohm.
• 4 Speakers (8 Ohm voice coils): Total impedance 2 Ohm.

Mixed connection of the speakers

Diagram illustrating a mixed connection of speakers and its corresponding total impedance table:

• 4 Speakers (4 Ohm voice coils): Total impedance 4 Ohm.
• 4 Speakers (8 Ohm voice coils): Total impedance 8 Ohm.

CAUTION!!! High sound pressure can damage your health! Please use the common sense when controlling volume!

Subwoofers Wiring Diagrams

The minimum permissible load impedance at the single channel is 1 ohm, in bridged mode 2 ohm. Use these formulas to calculate the load impedance of various types of connections.

Serial connection

Total impedance = ΩSub 1 + ΩSub 2 + ΩSub 3...

Parallel connection

Total impedance = 1 / (1/ΩSub 1 + 1/ΩSub 2 + 1/ΩSub 3...)

Schemes of Enabling the Load of the Subwoofer

Diagrams illustrating subwoofer connections (single subwoofer with D1, D2, or D4 voice coils; multiple subwoofers) and their total impedance tables for series, parallel, and mixed configurations.

• One subwoofer, coils in series: Tables for 1+1, 2+2, 4+4 Ohm voice coils with total impedances of 2, 4, 8 Ohm respectively.
• One subwoofer, coils in parallel: Tables for 1+1, 2+2, 4+4 Ohm voice coils with total impedances of 0.5, 1, 2 Ohm respectively.
• Subwoofers in series, coils in parallel: Tables for 1+1, 2+2, 4+4 Ohm voice coils with total impedances of 1, 2, 4 Ohm respectively.
• Subwoofers in series, coils in series: Tables for 1+1, 2+2, 4+4 Ohm voice coils with total impedances of 1.5, 3, 6 Ohm respectively.
• Subwoofers in parallel, coils in series: Tables for 1+1, 2+2, 4+4 Ohm voice coils with total impedances of 2, 4, 8 Ohm respectively.
• Subwoofers in series, coils in parallel: Tables for 1+1, 2+2, 4+4 Ohm voice coils with total impedances of 4, 8, 16 Ohm respectively.
• Subwoofers in parallel, coils in parallel: Tables for 1+1, 2+2, 4+4 Ohm voice coils with total impedances of 6, 12, 24 Ohm respectively.
• Subwoofers in parallel, coils in series: Tables for 1+1, 2+2, 4+4 Ohm voice coils with total impedances of 8, 16, 32 Ohm respectively.
• Subwoofers in parallel, coils in parallel: Tables for 1+1, 2+2, 4+4 Ohm voice coils with total impedances of 1, 2, 4 Ohm respectively.
• Subwoofers in parallel, coils in parallel: Tables for 1+1, 2+2, 4+4 Ohm voice coils with total impedances of 0.66, 1.33, 2.66 Ohm respectively.
• Subwoofers in parallel, coils in parallel: Tables for 1+1, 2+2, 4+4 Ohm voice coils with total impedances of 0.5, 1, 2 Ohm respectively.
• Subwoofers in parallel, coils in parallel: Tables for 1+1, 2+2, 4+4 Ohm voice coils with total impedances of 0.25, 0.5, 1 Ohm respectively.
• Subwoofers in parallel, coils in parallel: Tables for 1+1, 2+2, 4+4 Ohm voice coils with total impedances of 0.16, 0.33, 0.66 Ohm respectively.
• Subwoofers in parallel, coils in parallel: Tables for 1+1, 2+2, 4+4 Ohm voice coils with total impedances of 0.125, 0.25, 0.5 Ohm respectively.

CAUTION!!! High sound pressure can damage your health! Please use the common sense when controlling volume!

7. Specifications

*RMS Power at 14.4 V, THD 1%

8. Possible Faults and Their Solutions

1. The amplifier does not turn on.
   Problem solution: Check all the contacts and the presence of 9-15 V at the amplifier terminals. Check whether the control input of the amplifier "REM IN" receives the positive potential of +12 V.
2. Power turns on, but goes into protection (protection indicator lights up)
   Problem solution: Check if there is a short circuit (fault) on the amplifier output which is connected to the speakers or subwoofers. Make sure that commutation of the voice coils of the subwoofer is correct. The rated impedance of the voice coils should not be lower than the permissible rated load impedance of the amplifier. Check the supply voltage of the amplifier. It must be within the range of 9-15 V.
3. The amplifier turns on but at a high volume it goes in to protection.
   Problem solution: The amplifier may lack power. Make sure that the rated current of the alternator and the battery capacity is enough to power this amplifier. Check the amplifier for overheating. Check the load impedance.
4. The amplifier is turned on, but there is no sound from the speakers or subwoofer.
   Problem solution: Check the connection of the amplifier, the integrity of the interconnecting cable, HU, the speakers or the subwoofer.

9. Box Contents

• Amplifier - 1 pc.
• Owner's manual - 1 pc.
• Warranty card - 1 pc.
• Mounting Kit - 1 pc.
• Window decals - 2 pcs.

10. Warranty and Maintenance Info

Deaf Bonce products are warranted against defects concerning materials and their manufacturing under normal functioning conditions.

While the product is under warranty, defective parts will be repaired or replaced at the manufacturer's discretion. The defective product, along with notification about it, must be returned to the dealer from which it was purchased together with the warranty certificate duly filled in, complete with the original packaging. If the product is no longer under warranty, it will be repaired at the current costs.

Our company does not undertake any liability for damages due to transportation. Our company does not take any responsibility for: costs or loss of profit due to the impossibility to use the product, other accidental or consequential costs, expenses or damages suffered by the customer. Warranty according to laws in force.

For more information visit our website and carefully read warranty card. The manufacturer reserves the right to change design without prior notice.

11. Information on Disposal of Electrical and Electronic Equipment

Items marked with a "crisscrossed wheeled bin" symbol are not allowed to be disposed of together with usual household waste. These electrical and electronic products should be disposed of in special reception centers, equipped for recycling such products and components. For information about the location of the nearest disposal / recycling spot and the rules of delivery of waste please contact your local municipal office. Recycling and proper disposal helps to protect the environment and prevent harmful effects on health.

Manufacturer: Ningbo Sound Solution I&E Trading Co., Ltd

Made in China