Midea Dehumidifier User Manual

Introduction

Thank you for choosing Midea! This manual provides essential information for operating your new Midea dehumidifier safely and effectively. Please read it thoroughly and keep it for future reference.

The design and specifications are subject to change without prior notice for product improvement. Consult your dealer or manufacturer for details. Diagrams are for reference; the actual product appearance is the standard.

Contents

• Thank You Letter
• Safety Instructions
• Get to Know Your Product
• Product Installation
• Get to Know Your Features
• Removing Collected Water
• App Instructions
• Cleaning and Maintenance
• Troubleshooting Tips
• Warranty
• Return Policy

This manual contains helpful hints for proper use and maintenance, saving you time and money. It also includes troubleshooting tips for common problems.

Safety Precautions

Read all safety precautions before operation and installation. Following these instructions prevents injury and property damage. Ignoring them may cause harm or damage.

Explanation of Symbols

⚠️ WARNING: Indicates a hazard with a medium level of risk. Failure to avoid may result in death or serious injury.

⚠️ CAUTION: Indicates a hazard with a low degree of risk. Failure to avoid may result in minor or moderate injury.

General Warnings

• Do not exceed the power outlet or connection device rating.
• Do not operate or stop the unit by switching the power on/off.
• Do not use an unspecified or damaged power cord.
• Do not modify the power cord length or share the outlet with other appliances.
• Do not insert or pull the plug with wet hands.
• Do not install in locations exposed to combustible gas.
• Do not place the unit near a heat source.
• Disconnect power if strange sounds, smell, or smoke occurs.
• Never attempt to repair the unit yourself.
• Turn off and unplug the unit before cleaning.
• Do not use near flammable gas or combustibles (gasoline, benzene, thinner, etc.).
• Do not drink or use the drained water.
• Do not remove the side access tank during operation.
• Do not use in small or water-splashing areas.
• Place the unit on a level, sturdy floor.
• Do not cover intake or exhaust openings.
• Exercise care when using around infants, children, elderly, or persons with reduced capabilities.
• Do not use in areas where chemicals are handled.
• Never insert fingers or foreign objects into openings. Warn children of these dangers.
• Do not place heavy objects on the power cord.
• Do not climb or sit on the unit.
• Always insert filters securely. Clean filters every two weeks.
• If water enters the unit, turn off, disconnect power, and contact a service technician.
• Do not place flower vases or other water containers on top of the unit.
• Do not use extension cords.

Additional Cautions

• If the supply cord is damaged, it must be replaced by the manufacturer, service agent, or qualified persons.
• Disconnect from power supply before cleaning or maintenance.
• If combustible gas accumulates, it may cause fire.
• If the appliance is knocked over, turn off, unplug, and inspect for damage. Contact a technician if damaged.
• Do not use in water-damaged environments.
• In thunderstorms, cut off power to avoid lightning damage.
• Arrange the power cord away from traffic areas; do not run under carpeting, furniture, or appliances.
• Discard or return damaged units for examination/repair.
• Ensure proper grounding for shock and fire hazard prevention. The power cord has a three-prong grounding plug.
• Use a properly grounded wall receptacle. If not adequately grounded or protected, have a qualified electrician install a proper receptacle.
• The unit's circuit board (PCB) has a fuse for overcurrent protection (e.g., T 3.15A/250V).

Electronic Work Precautions

Diagram Description: Shows connections between Main Control, Display, and Power Supply Cord.

⚠️ CAUTION: Risk of fire with A2L flammable materials.

IMPORTANT NOTE: Read this manual carefully before installing or operating. Save for future reference.

Explanation of Symbols on Unit

• ? CAUTION: Operation manual should be read carefully.
• ? CAUTION: Service personnel should handle with reference to the installation manual.
• ℹ️ CAUTION: Information is available (operating or installation manual).

Warning for using R32 Refrigerant

WARNING: Flammable! Refrigerant R32 is used within the appliance.

• When maintaining or disposing, recover R32 properly; do not discharge to air directly.
• Comply with national gas regulations.
• Keep ventilation openings clear of obstruction.
• Store the appliance to prevent mechanical damage.
• Store in a well-ventilated area corresponding to the room size specified for operation.
• Personnel working on or breaking into a refrigerant circuit must hold a valid certificate for safe refrigerant handling.
• Examples of such procedures include: breaking into the refrigerating circuit, opening sealed components, opening ventilated enclosures.
• No open fire or spark/arcing devices should be near the appliance to avoid igniting the flammable refrigerant. Follow instructions carefully for storage and maintenance.
• Do not use means to accelerate defrosting or cleaning other than those recommended by the manufacturer.
• Store in a room without continuously operating ignition sources (e.g., open flames, operating gas appliances, operating electric heaters).
• Do not pierce or burn.
• Be aware that refrigerants may not contain an odor.

Get to Know Your Product

Identification of Parts

Diagram Description: An illustration shows the dehumidifier with parts labeled:

• Control panel
• Handle (both sides)
• Front panel
• Water level window
• Side Access Tank
• Caster
• Air outlet grille
• Air filter (Air inlet grille)
• Continuous drain hose outlet
• Pump drainage (only for pump model)
• Power plug storage
• Power cord and plug

Illustrations are for explanation only; actual shape may vary.

Accessories

• Caster (4 pc)
• Cushion pad (1 pc)

Optional Accessories

• Pump drain hose *1 pc (For the unit with pump feature)

Product Installation

Positioning the Unit

Diagram Description: Shows required clearance around the dehumidifier: 20cm (approx. 8 inches) on front and sides, 40cm (approx. 16 inches) on top and rear air outlet.

Casters: Located on the bottom. They move freely. Do not force over carpet. Do not move with water in the bucket to avoid tipping and spilling.

For optimal performance, especially in basements, ensure adequate air circulation. This dehumidifier is intended for indoor residential use only, not for commercial or industrial applications.

• Place on a smooth, level floor strong enough to support the unit with a full water bucket.
• Allow at least 20cm (8 inches) clearance on all sides for air circulation, and at least 40cm (16 inches) for the air outlet.
• Operate in areas where temperatures do not fall below 5°C (41°F) to prevent coil frosting.
• Place away from clothes dryers, heaters, or radiators.
• Use to prevent moisture damage to stored items like books or valuables.
• Operate in an enclosed area for best results. Close doors, windows, and other openings.
• Before tilting or moving, empty the water bucket and disconnect the power cord.

When Using Your Product

NOTE: Be careful when moving the machine if the water bucket is nearly full to avoid tipping.

First Time Using

Ensure the water plug is securely installed and operate the unit continuously for 24 hours.

Working Condition Requirement

• Temperature: Min. 5°C (41°F) to Max. 32°C (90°F)
• Humidity: Min. 30% (RH) to Max. 80% (RH)

Precautions for Use

• After a quick restart, wait 3 minutes for the operation to resume.
• Ensure correct power connection, preferably a single-socket outlet.
• Ensure proper ground connection.
• Ensure the water tank is properly installed.

Notes on Operation:

• For first-time use, run continuously for 24 hours with the plastic cover securely installed.
• Condensation may form on the surface in open spaces with open windows, which is normal.
• If the unit is switched off and needs to be turned on again quickly, wait approximately three minutes.
• Do not connect to a multiple socket outlet shared with other appliances.
• Select a suitable location with easy access to an electrical outlet.
• Plug into a grounded socket-outlet.
• The side access tank must be correctly fitted for the unit to operate.

Caster Installation

Diagram Description: Shows steps for attaching casters and cushion pads.

1. Pull out the side access tank.
2. Take out a cushion pad and four casters from the bucket, then reinstall the side access tank.
3. Tilt the unit on its side and insert two casters. Rotate the unit and insert the other two casters.
4. Leave the unit standing upright for half an hour before use.

Get to Know Your Features

Control Panel Features

Diagram Description: An illustration of the control panel with numbered buttons and indicators.

Control panel illustrations are for explanation; your unit may differ slightly.

Detailed Function Explanations

• POWER ON/OFF Button: Turns the dehumidifier on and off.
• WIRELESS Button: Press and hold the POWER button for 3 seconds to initiate Wireless connection mode. The LED DISPLAY shows 'AP'. If connection is successful within 8 minutes, the unit exits mode automatically. If it fails, it exits automatically. A quick glance light flashes white when connecting to the internet.
• TIMER Function: Use with UP/DOWN buttons for Auto start/stop.
  • Auto start setting: In shutdown state, press Timer button. Use UP/DOWN to set time (0.5 hr increments up to 10 hrs, then 1 hr increments up to 24 hrs).
  • Auto stop setting: In startup state, press Timer button. Use UP/DOWN to set time (0.5 hr increments up to 10 hrs, then 1 hr increments up to 24 hrs).

  Timing can be adjusted up to 24 hours. Press again to check status. Cancel by setting time to 0.0.

• MODE Function: Cycles through Set, Continuous, Dryer, Comfort modes.
  • Set Mode: Manually adjust desired humidity (35%-85% in 5% increments).
  • Continuous Mode: Works continuously to remove moisture. Humidity cannot be adjusted.
  • Comfort Mode (Optional): Automatically controls humidity to 45%-55% based on room temperature. Humidity cannot be adjusted.
  • Dryer Mode (Optional): Filters moisture and blows warmer air at a higher fan speed. Unit may quit Dryer mode after 10 hours. For best results, wring out excess moisture from clothes, direct airflow at wet clothes, and allow 30-50cm distance.
• UP AND DOWN Buttons: Set humidity (35%-85% RH) and timer.
• FAN SPEED Function: Selects fan speed (Low/High).
• DISPLAY: Shows ambient/set humidity, timer, and error codes.

Error Codes

• ES/EH61: Evaporator coil temperature sensor error. Unplug/replug. Call service if repeated.
• AS/EH60: Room temperature sensor error. Unplug/replug. Call service if repeated.
• P2: Bucket is full or not positioned correctly. Empty and reposition bucket.
• P1: Unit is defrosting. Allow time for automatic defrost.
• EH00: Indoor EEPROM error. Unplug/replug. Call service if repeated.

More Features

• AUTO SHUT OFF: Unit shuts off when bucket is full, removed, or not replaced properly. Fan may run for 30 seconds. Empty bucket when Full indicator lights up. Wait 3 minutes before restarting.
• CHECK FILTER FEATURE: Filter reminder activates after 250 hours of operation. Press and hold FAN button for 3 seconds after cleaning to reset.
• AUTO-RESTART: Unit restarts with previous settings after power interruption.

Removing Collected Water

There are three ways to remove collected water:

• Type 1: Bucket drainage: When the bucket is full, the Full indicator lights up. The compressor and fan turn off. Display shows P2. Pull the bucket out halfway, lift by the handle, and pour out water. Ensure the bucket is correctly reinstalled for operation.
• Type 2: Water hose drainage (continuous): Attach a water hose (approx. 5/16" diameter, female threaded end) to the drain outlet. Remove the water plug, insert the hose, and lead it to a floor drain or suitable facility. Ensure the hose is secure, leak-free, and slopes downwards. Select desired humidity and fan speed for continuous draining.
• Type 3: Pump drainage (only for pump model): Connect the pump drain hose by pressing the tightening ring and pulling out the plug. Insert the hose onto the drainage joint, ensuring a secure seal. Place the other end in the desired drainage location (floor drain, container, outdoors). To remove, press the ring, pull out the hose, and replace the plug.

When removing the bucket, do not touch internal parts. Ensure the bucket is pushed in gently. If the pump hose disconnects, reinstall it properly. Dry any residual water. If the bucket is removed, the unit will beep and display 'Eb'.

For pump drainage, the maximum distance and rise is 5m. Exceeding this may cause damage or leaks. If removing the hose for bucket mode, reinsert the drain plug.

App Instructions

Specification of Wireless Module

• Model: US-SK105
• Antenna Type: Printed PCB Antenna
• Frequency: WLAN 2400-2483.5 MHz
• Max Transmitted Power: <20 dBm
• Dimensions: 41 x 24 x 5 mm
• Operation Temperature: 0°C ~ 45°C / 32°F ~ 113°F
• Operation Humidity: 10% ~ 85%
• Power Input: DC 5V/500 mA

Precautions

• App Compatibility: Available for iOS and Android. Keep app updated. Midea is not responsible for compatibility issues with older versions.
• Wireless Security: Supports WPA-PSK / WPA2-PSK / WPA3-SAE. Encryption is recommended.
• Connectivity: Network issues may cause timeouts or unsynchronization. If the network is unavailable, re-run configuration. Changes in wireless network require reconfiguration.
• Configuration: Process may vary. Check the service website for details.

Midea is not responsible for problems caused by incompatibility or network issues with your router or mobile phone.

Using the SmartHome App

1. Download the SmartHome app: Scan the QR code or search on the App Store/Google Play.
2. Log in: Open the app, log in with an existing account, create a new one, or use a 3rd party login.
3. Connecting the device:
   • If prompted, tap "Smart devices discovered nearby" to add your device.
   • If no message appears, tap "+" and select your device from the list or add it manually by category (e.g., Dehumidifier).
   • Follow the app's instructions to connect to the wireless network.
4. Controlling the device: After successful pairing, a device card appears in the app. Basic functions (humidity, on/off) are available as shortcuts. Tapping the card reveals additional features. (Actual design may vary due to app updates).

Compliance

This dehumidifier complies with relevant provisions of RE Directive 2014/53/EU.

• Wireless module models: US-SK105
• FCC ID: 2ADQOMDNA21
• IC: 12575A-MDNA21

This device complies with Part 15 of the FCC Rules and Innovation, Science and Economic Development Canada's licence-exempt RSS(s).

Operation is subject to two conditions: (1) This device may not cause harmful interference; (2) This device must accept any interference, including interference that may cause undesired operation.

Operate only according to instructions. Unauthorized modifications void user authority.

Complies with FCC radiation exposure limits for uncontrolled environments. Maintain at least 20cm (8 inches) proximity to the antenna during normal operation.

NOTE: This equipment has been tested and found to comply with Class B digital device limits (FCC Part 15) for reasonable protection against harmful interference in residential installations. It generates, uses, and radiates RF energy. If not installed/used per instructions, it may cause interference. If interference occurs, try correcting it by:

• Reorienting or relocating the receiving antenna.
• Connecting to a different circuit.
• Consulting the dealer or an experienced radio/TV technician.

Cleaning and Maintenance

How To Clean & Care For Your Product

Turn off and unplug the dehumidifier before cleaning.

1. Clean the Grill and Case: Use water and mild detergent. Do not use bleach or abrasives. Avoid splashing water directly onto the unit. Use a vacuum attachment or brush for soiled grilles.
2. Clean the bucket: Every few weeks, clean the bucket to prevent mold and bacteria. Partially fill with water and mild detergent, swish, empty, and rinse. Do not use a dishwasher. Ensure the bucket is securely seated after cleaning.
3. Clean the air filter: Remove and wash the filter every two weeks. Dry thoroughly before reinstalling.
   CAUTION: DO NOT operate without a filter; dirt and lint will clog it and reduce performance.
4. Clean the pump filter: Clean every two weeks. Remove the side access tank and bucket top cover. Remove the screw, take out the pump drainage structure, and clean the filter at the bottom of the hose. Reinstall the filter and structure.

When Not Using The Unit For Long Time Periods

Follow these steps for storage:

1. Remove water from the bucket.
2. Remove water plug to drain any excess water.
3. Re-insert the water plug.
4. Clean the grille and case.
5. Clean the air filter.
6. Clean the bucket.
7. Store the unit upright in a dry, well-ventilated place.

• Clean the main unit, side access tank, and air filter.
• Dry any water droplets on the chassis after removing the bucket.
• Wrap the cord with the power cord buckle.
• Properly restore the bucket and place the unit upright.
• Cover the unit with a plastic bag.
• Store in a dry, well-ventilated place.

Troubleshooting Tips

Malfunction Diagnosis

Check the following for common occurrences:

Design and specifications are subject to change. Consult sales agency or manufacturer. Updates are available on the service website.

Warranty

Dehumidifier Limited Warranty

Your product is protected by this Limited Warranty. Service must be obtained from Midea Consumer Services or an authorized Midea servicer.

• Warranty: One Year full warranty from original purchase date.
• Midea's Responsibilities: Midea will pay for repairing or replacing defective parts.
• Consumer's Responsibilities: Diagnostics, removal, transportation, and reinstallation costs. Costs for service calls related to items under "Normal Responsibilities of the Consumer". Midea replacement parts are warranted only for the original warranty period.

Normal Responsibilities of the Consumer

This warranty applies to ordinary household use. The consumer is responsible for:

1. Proper use according to instructions.
2. Routine maintenance and cleaning.
3. Proper installation by an authorized professional according to instructions and local codes.
4. Proper connection to a grounded power supply, replacement of fuses, repair of loose connections or house wiring defects.
5. Expenses for making the appliance accessible for servicing.
6. Damages to finish after installation.

Exclusions

This warranty does not cover:

1. Damage from possession (other than defects), improper installation, or unreasonable use, including failure to provide maintenance or follow instructions.
2. Service performed by unauthorized persons; external causes like abuse, misuse, inadequate power supply, or acts of God.
3. Commercial, business, rental, or other non-consumer use.
4. Products without original or altered serial numbers.

Some states do not allow exclusion/limitation of incidental/consequential damages, so these limitations may not apply to you.

If You Need Service

• Keep your bill of sale or payment record.
• Contact Midea Consumer Services or an authorized Midea servicer at 1-866-646-4332.
• For questions about service locations, contact consumer relations.

Return Policy

Questions about installing or operating?

• For assistance, call Customer Service at 1-866-646-4332.
• Have your sales receipt, serial number, and product model number ready.

Products may be returned within 30 days of purchase with receipt. After 30 days, the product is covered under limited warranty. Refer to the warranty section for details.

? Save your receipt.

30 days return period.