Kaysun Remote Controller User Manual

Remote Controller Specifications

Quick Start Guide

1. FIT BATTERIES: Slide the back cover downward, expose the battery compartment, insert batteries matching (+) and (-) ends, then slide the cover back into place.
2. SELECT MODE: Press the [MODE] button to cycle through AUTO, COOL, DRY, HEAT, FAN modes.
3. SELECT TEMPERATURE: Use the [TEMP UP] and [TEMP DOWN] buttons to set your desired temperature.
4. SELECT FAN SPEED: Use the [FAN SPEED] button to select AUTO, LOW, MED, or HIGH fan speeds.
5. POINT REMOTE TOWARD UNIT: Aim the remote control at the air conditioner unit.
6. PRESS POWER BUTTON: Press the [ON/OFF] button to turn the unit on.

NOT SURE WHAT A FUNCTION DOES? Refer to the "How to Use Basic Functions" and "How to Use Advanced Functions" sections of this manual for a detailed description of how to use your air conditioner.

SPECIAL NOTE

• Button designs on your unit may differ slightly from the example shown.
• If the indoor unit does not have a particular function, pressing that function's button on the remote control will have no effect.
• When there are wide differences between "Remote controller Manual" and "USER'S MANUAL" on function description, the description of "USER'S MANUAL" shall prevail.

Handling the Remote Controller

Inserting and Replacing Batteries

Your air conditioning unit may come with two batteries (some units). Put the batteries in the remote control before use.

1. Slide the back cover from the remote control downward, exposing the battery compartment.
2. Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols inside the battery compartment.
3. Slide the battery cover back into place.

BATTERY NOTES

• For optimum product performance: Do not mix old and new batteries, or batteries of different types.
• Do not leave batteries in the remote control if you don't plan on using the device for more than 2 months.

BATTERY DISPOSAL

Do not dispose of batteries as unsorted municipal waste. Refer to local laws for proper disposal of batteries.

TIPS FOR USING REMOTE CONTROL

• The remote control must be used within 8 meters of the unit.
• The unit will beep when remote signal is received.
• Curtains, other materials and direct sunlight can interfere with the infrared signal receiver.
• Remove batteries if the remote will not be used more than 2 months.

NOTES FOR USING REMOTE CONTROL

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• Changes or modifications not approved by the party responsible for compliance could void user's authority to operate the equipment.

Buttons and Functions

• [ON/OFF] button: Turns the unit on or off.
• [TEMP UP] button: Increases temperature in 1°C (1°F) increments. Max. temperature is 30°C (86°F).
  Note: Pressing [TEMP UP] and [TEMP DOWN] buttons simultaneously for 3 seconds will alternate the temperature display between °C and °F.
• [SET] button: Scrolls through operation functions as follows: Follow Me (?) → AP mode (?) → Follow Me (?)... The selected symbol will flash on the display area; press [OK] button to confirm.
• [TEMP DOWN] button: Decreases temperature in 1°C (1°F) increments. Min. temperature is 16°C (60°F).
• [FAN SPEED] button: Selects fan speeds in the following order: AUTO → LOW → MED → HIGH.
  Note: Holding this button down for 2 seconds will activate the Silence feature.
• [SWING] button: Starts and stops the horizontal louver movement. Hold down for 2 seconds to initiate vertical louver auto swing feature (some units).
• [MODE] button: Scrolls through operation modes as follows: AUTO → COOL → DRY → HEAT → FAN.
  Note: HEAT mode is not supported by cooling-only appliances.
• [SLEEP] button: Saves energy during sleeping hours.
• [OK] button: Used to confirm the selected functions.
• [TIMER] button: Set timer to turn unit on or off.
• [FRESH] button: Used to start/stop the air fresh feature.
• [CLEAN] button: Used to start/stop the Self Clean or Active Clean function (Model dependent, please refer to the USER'S OPERATION & INSTALLATION MANUAL).
• [LED] button: Turns the indoor unit's LED display and air conditioner buzzer on and off (model dependent), creating a comfortable and quiet environment.
• [TURBO] button: Enables the unit to reach preset temperature in the shortest possible time.

Remote Screen Indicators

Information is displayed when the remote controller is powered up.

• Transmission Indicator: Lights up when the remote sends a signal to the indoor unit.
• TIMER ON display: Indicates the timer is set to turn the unit ON.
• TIMER OFF display: Indicates the timer is set to turn the unit OFF.
• Silence feature display: Indicates the Silence mode is active.
• FAN SPEED display: Shows the selected fan speed (Silence, LOW, MED, HIGH, AUTO).
  Note: Some models may display fan speed as a percentage from 1% to 100%. This fan speed cannot be adjusted in AUTO or DRY mode.
• MODE display: Shows the current operating mode: AUTO, COOL, DRY, HEAT, FAN.
• ECO display: Appears when the ECO feature is activated.
• GEAR display: Appears when the GEAR feature is activated.
• LOCK display: Appears when the LOCK feature is activated, preventing accidental changes.
• Temperature/Timer/Fan speed display: Shows the set temperature by default, or the fan speed or timer setting when using TIMER ON/OFF functions.
  Temperature range: 16-30°C (60-86°F) or (20-28°C/68-82°F) (Model dependent). Timer setting range: 0-24 hours. Fan speed setting range: AU -100%. This display is blank when operating in FAN mode.
• Breeze Away display (some units): Indicates the Breeze Away feature is active.
• Active clean feature display: Indicates the Active Clean feature is active.
• Fresh feature display: Indicates the Fresh feature is active.
• Sleep mode display: Indicates the Sleep mode is active.
• Follow me feature display: Indicates the Follow Me feature is active.
• Wireless control feature display (some units): Indicates wireless control is active.
• Low battery detection display: Flashes when the battery level is low.

Diagrammatic Descriptions of Screen Elements:

• Horizontal louver swing display: Shows the horizontal louver movement.
• Vertical louver auto swing display: Shows the vertical louver movement.
• TURBO mode display: Indicates the Turbo mode is active.
• A / B indicators: Described as indicators on the screen, their specific meaning may vary by model.

Note: All indicators shown in the figure are for the purpose of clear presentation. During actual operation, only the relevant function signs are shown on the display window.

How to Use Basic Functions

ATTENTION: Before operation, please ensure the unit is plugged in and power is available.

AUTO Mode

Steps:

1. Press the [MODE] button until AUTO mode is selected.
2. Set your desired temperature using the [TEMP UP] / [TEMP DOWN] buttons.
3. Turn on the air conditioner by pressing the [ON/OFF] button.

Note: In AUTO mode, the unit will automatically select the COOL, FAN, or HEAT function based on the set temperature. Fan speed cannot be set in AUTO mode.

COOL or HEAT Mode

Steps:

1. Press the [MODE] button until COOL or HEAT mode is selected.
2. Set your desired temperature using the [TEMP UP] / [TEMP DOWN] buttons.
3. Set the fan speed using the [FAN SPEED] button.
4. Turn on the air conditioner by pressing the [ON/OFF] button.

DRY Mode

Steps:

1. Press the [MODE] button until DRY mode is selected.
2. Set your desired temperature using the [TEMP UP] / [TEMP DOWN] buttons.
3. Turn on the air conditioner by pressing the [ON/OFF] button.

Note: In DRY mode, fan speed cannot be set as it is automatically controlled.

FAN Mode

Steps:

1. Press the [MODE] button until FAN mode is selected.
2. Set the fan speed using the [FAN SPEED] button.
3. Turn on the air conditioner by pressing the [ON/OFF] button.

Note: In FAN mode, you cannot set the temperature. As a result, no temperature displays on the remote screen.

Setting the TIMER

TIMER ON/OFF - Set the amount of time after which the unit will automatically turn on/off.

TIMER ON setting

Steps:

1. Press the [TIMER] button to initiate the ON time sequence.
2. Press the [TEMP UP] or [TEMP DOWN] button multiple times to set the desired time to turn on the unit. (Increments of 30 minutes up to 10 hours, then 1 hour increments up to 24 hours).
3. Point the remote to the unit and wait 1 second; the TIMER ON will be activated.

TIMER OFF setting

Steps:

1. Press the [TIMER] button to initiate the OFF time sequence.
2. Press the [TEMP UP] or [TEMP DOWN] button multiple times to set the desired time to turn off the unit. (Increments of 30 minutes up to 10 hours, then 1 hour increments up to 24 hours).
3. Point the remote to the unit and wait 1 second; the TIMER OFF will be activated.

Note:

• When setting TIMER ON or TIMER OFF, the time increases by 30-minute increments up to 10 hours. After 10 hours, it increases in 1-hour increments up to 24 hours. The timer reverts to 0.0 after 24 hours.
• Cancel either function by setting its timer to 0.0h.

TIMER ON & OFF setting (example)

Keep in mind that the time periods you set for both functions refer to hours after the current time.

Example: If the current time is 1:00 PM, to set the timer as described in the diagram, the unit will turn on 2.5 hours later (at 3:30 PM) and turn off at 6:00 PM.

Diagram description: Shows a timeline starting from current time 1 PM, then 2:00 PM, 3:00 PM, 3:30 PM (Unit turns ON), 4 PM, 5 PM, 6 PM (Unit turns OFF).

How to Use Advanced Functions

Swing function

Steps:

1. Press the [SWING] button. The horizontal louver will swing up and down automatically. Press again to stop it.
2. Keep pressing the [SWING] button for more than 2 seconds to activate the vertical louver swing function (Model dependent).
3. Continue pressing the [SWING] button to cycle through five different airflow directions. The louver will move to a selected range. Press the button until your preferred direction is reached.

Note: When the unit is off, press and hold [MODE] and [SWING] buttons together for one second to open the louver for cleaning. Press and hold [MODE] and [SWING] buttons together for one second to reset the louver (Model dependent).

LED DISPLAY

Steps:

1. Press the [LED] button to turn the indoor unit's LED display and buzzer on or off (model dependent).
2. Press and hold the [LED] button for more than 5 seconds (some units). The indoor unit will display the actual room temperature. Press and hold for more than 5 seconds again to revert back to displaying the setting temperature.

Additional Functions

Silence function

Keep pressing the [FAN] button for more than 2 seconds to activate/disable the Silence function (some units). Due to low-frequency operation of the compressor, this may result in insufficient cooling and heating capacity. Pressing [ON/OFF], [MODE], [SLEEP], [TURBO], or [CLEAN] buttons while operating will cancel the silence function.

LOCK function

Press the [CLEAN] button and [TURBO] button simultaneously for more than 5 seconds to activate the Lock function. All buttons will not respond except for [CLEAN] and [TURBO]. Press these two buttons for two seconds again to disable locking.

SET function

To set a function:

1. Press the [SET] button to enter the function setting mode.
2. Press the [SET] button or [TEMP UP] / [TEMP DOWN] buttons to select the desired function. The selected symbol will flash on the display area.
3. Press the [OK] button to confirm.

To cancel a selected function: Perform the same procedures as above.

Scrolling through operation functions using [SET] button:

• Breeze Away (?)
• Fresh (❄️)
• Sleep (?)
• Follow Me (?)
• AP mode (?)

[*]: If your remote controller has dedicated Breeze Away, Fresh, or Sleep buttons, you cannot use the [SET] button to select these features.

Breeze Away function (?) (some units):

This feature avoids direct airflow blowing on the body, making you feel indulging in silky coolness. This feature is available under Cool, Fan, and Dry modes only.

FRESH function (❄️) (some units):

When the FRESH function is initiated, the ion generator is energized and helps to purify the air in the room.

Sleep function (?):

The SLEEP function is used to decrease energy use while you sleep (and don't need the same temperature settings to stay comfortable). This function can only be activated via remote control. For details, see "sleep operation" in the "USER'S MANUAL".
Note: The SLEEP function is not available in FAN or DRY mode.

Follow me function (?):

The FOLLOW ME function enables the remote control to measure the temperature at its current location and send this signal to the air conditioner every 3 minutes. When using AUTO, COOL, or HEAT modes, measuring ambient temperature from the remote control (instead of from the indoor unit itself) helps the air conditioner optimize the temperature around you for maximum comfort.

NOTE: Press and hold the [TURBO] button for seven seconds to start/stop the memory feature of the Follow Me function.

• If the memory feature is activated, "On" displays for 3 seconds on the screen.
• If the memory feature is stopped, "OF" displays for 3 seconds on the screen.
• While the memory feature is activated, pressing the [ON/OFF] button, shifting the mode, or a power failure will not cancel the Follow Me function.

AP function (?) (some units):

Choose AP mode for wireless network configuration. For some units, this does not work by pressing the [SET] button. To enter AP mode, continuously press the [LED] button seven times within 10 seconds.

Disclaimer

The design and specifications are subject to change without prior notice for product improvement. Consult with the sales agency or manufacturer for details.

Product Information: CR2756-RG10(D2S), 16117000A37345, Version Date: 2020.07.13

Contact Information

Kaysun by Frigicoll

MAIN OFFICE:
Blasco de Garay, 4-6
08960 Sant Just Desvern (Barcelona)
Tel. +34 93 480 33 22
http://www.frigicoll.es/
http://www.kaysun.es/en/

MADRID:
Senda Galiana, 1
Polígono Industrial Coslada
Coslada (Madrid)
Tel. +34 91 669 97 01
Fax. +34 91 674 21 00
madrid@frigicoll.es