Kaysun KID-06 S Wired Controller User Manual

Remote Controller Specifications

Quick Start Guide

Follow these steps to get started:

1. FIT BATTERIES: Insert batteries into the remote control.
2. SELECT MODE: Press the MODE button to choose your desired operating mode (AUTO, COOL, DRY, HEAT, FAN).
3. SELECT TEMPERATURE: Use the TEMP [up arrow] or TEMP [down arrow] buttons to set the desired temperature.
4. SELECT FAN SPEED: Press the FAN button to select the fan speed (Auto-100%).
5. POINT REMOTE TOWARD UNIT: Aim the remote control at the indoor unit.
6. PRESS POWER BUTTON: Press the ON/OFF button to start the unit.

NOT SURE WHAT A FUNCTION DOES? Refer to the "How to Use Basic Functions" and "How to Use Advanced Functions" sections for detailed descriptions.

SPECIAL NOTE:

• Button designs may differ slightly from the examples shown.
• If the indoor unit lacks a specific function, pressing its button on the remote will have no effect.
• In case of discrepancies between the "Remote Controller Manual" and "USER'S MANUAL" regarding function descriptions, the "USER'S MANUAL" description prevails.

Handling the Remote Controller

Inserting and Replacing Batteries

Your air conditioning unit may come with batteries. Insert them into the remote control before use.

1. Slide the back cover downwards to expose the battery compartment.
2. Insert batteries, matching the (+) and (-) ends with the symbols inside the compartment.
3. Slide the battery cover back into place.

BATTERY NOTES

• For optimum performance, do not mix old and new batteries, or batteries of different types.
• Remove batteries if the remote control will not be used for more than 2 months.

BATTERY DISPOSAL

Do not dispose of batteries as unsorted municipal waste. Refer to local laws for proper disposal.

TIPS FOR USING REMOTE CONTROL

• The remote control must be used within 8 meters of the unit.
• The unit will beep when a remote signal is received.
• Curtains, other materials, and direct sunlight can interfere with the infrared signal receiver.
• Remove batteries if the remote will not be used for more than 2 months.

NOTES FOR USING REMOTE CONTROL

The device complies with local national regulations.

• In Canada, it complies with CAN ICES-3(B)/NMB-3(B).
• In the USA, this device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• Changes or modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment.

Buttons and Functions

Familiarize yourself with the remote control. For detailed operating instructions, refer to the "How to Use Basic Functions" and "How to Use Advanced Functions" sections.

• ON/OFF: Turns the unit on or off.
• TEMP [up arrow]/[down arrow]: Increases or decreases temperature in 0.5°C increments. Max. temperature is 30°C. Pressing both [up arrow] and [down arrow] buttons simultaneously for 3 seconds alternates the temperature display between Celsius and Fahrenheit.
• MODE: Scrolls through operation modes: AUTO → COOL → DRY → HEAT → FAN.
• [Fan Icon] button: Enjoy even, comfortable cooling without a noticeable breeze. This feature is available only under COOL mode.
• SET: Scrolls through operation functions: Active clean [icon] → Fresh [icon] → Sleep [icon] → Follow Me [icon] → AP mode [icon] → Active clean... The selected symbol flashes on the display; press OK to confirm.
• OK: Used to confirm selected functions.
• FAN SPEED: Selects fan speeds in the order: Auto → 20% → 40% → 60% → 80% → 100%. Press the TEMP [up arrow] or TEMP [down arrow] button to increase/decrease fan speed in 1% increments.
• SWING: Starts and stops the horizontal louver movement.
• BOOST: Activates the unit to reach the preset temperature as quickly as possible.
• TIMER: Set timer to turn the unit on or off.
• ECO/GEAR: Press to enter energy-efficient modes: ECO → GEAR (75%) → GEAR (50%) → Previous setting mode → ECO...
• TEMP [down arrow]: Decreases temperature in 0.5°C increments. Min. temperature is 16°C.
• VANE: Press to enter the louver setting mode.
• LED: Turns the indoor unit's LED display and air conditioner buzzer on and off, creating a comfortable and quiet environment.

Model: KID-06 S

Remote Screen Indicators

Information is displayed when the remote controller is powered up.

• Transmission Indicator: Lights up when the remote sends a signal to the indoor unit.
• TIMER ON display: Indicates timer is set to turn ON.
• TIMER OFF display: Indicates timer is set to turn OFF.
• Silence feature display: Indicates Silence function is active.
• FAN SPEED display: Shows the selected fan speed (Silence, Low, Med, High, Auto).
• MODE display: Shows the current mode (AUTO, COOL, DRY, HEAT, FAN).
• ECO display: Shows when ECO feature is activated.
• GEAR display: Shows when GEAR feature is activated.
• LOCK display: Shows when LOCK feature is activated.
• Temperature/Timer/Fan speed display: Shows set temperature, fan speed, or timer setting.
• Other indicators include: Breezeless display, Clean feature display, Fresh feature display, Sleep mode display, Follow me feature display, Wireless control feature display, Low battery detection display.

Note: All indicators shown are for presentation; actual operation displays only relevant function signs.

How to Use Basic Functions

Basic operation: Ensure the unit is plugged in and power is available before operation.

SETTING TEMPERATURE

The operating temperature range is 16-30°C. You can increase or decrease the set temperature in 0.5°C increments.

AUTO Mode

The unit automatically selects COOL, FAN, or HEAT operation based on the set temperature.

1. Press the MODE button to select AUTO.
2. Set your desired temperature using the TEMP [up arrow] or TEMP [down arrow] button.
3. Press the ON/OFF button to start the unit.

NOTE: FAN SPEED cannot be set in AUTO mode.

COOL Mode

1. Press the MODE button to select COOL mode.
2. Set your desired temperature using the TEMP [up arrow] or TEMP [down arrow] button.
3. Press the FAN button to select the fan speed in a range of Auto-100%.
4. Press the ON/OFF button to start the unit.

DRY Mode (dehumidifying)

1. Press the MODE button to select DRY.
2. Set your desired temperature using the TEMP [up arrow] or TEMP [down arrow] button.
3. Press the ON/OFF button to start the unit.

NOTE: FAN SPEED cannot be changed in DRY mode.

FAN Mode

1. Press the MODE button to select FAN mode.
2. Press the FAN button to select the fan speed in a range of Auto-100%.
3. Press the ON/OFF button to start the unit.

NOTE: Temperature cannot be set in FAN mode; the remote control's LCD screen will not display temperature.

HEAT Mode

1. Press the MODE button to select HEAT mode.
2. Set your desired temperature using the TEMP [up arrow] or TEMP [down arrow] button.
3. Press the FAN button to select the fan speed in a range of Auto-100%.
4. Press the ON/OFF button to start the unit.

NOTE: As outdoor temperature drops, the HEAT function's performance may be affected. In such instances, using this air conditioner in conjunction with other heating appliances is recommended.

Setting the TIMER

TIMER ON/OFF: Set the amount of time after which the unit will automatically turn on/off.

TIMER ON setting

Press the TIMER button to initiate the ON time sequence. Press the TEMP [up arrow] or [down arrow] button multiple times to set the desired time to turn on the unit. Point the remote to the unit and wait 1 second; the TIMER ON will be activated.

TIMER OFF setting

Press the TIMER button to initiate the OFF time sequence. Press the TEMP [up arrow] or [down arrow] button multiple times to set the desired time to turn off the unit. Point the remote to the unit and wait 1 second; the TIMER OFF will be activated.

NOTE:

1. When setting TIMER ON or TIMER OFF, the time increases by 30-minute increments up to 10 hours. After 10 hours, it increases in 1-hour increments up to 24 hours. The timer reverts to 0.0 hours after 24.
2. Cancel either function by setting its timer to 0.0 hours.

TIMER ON & OFF setting (example)

The time periods set refer to hours after the current time.

Example: If the current time is 1:00 PM, setting the timer as described will turn the unit on 2.5 hours later (at 3:30 PM) and turn it off 5 hours later (at 6:00 PM).

How to Use Advanced Functions

Vane function

Press the VANE button when the unit is turned on. This activates the louver setting feature. Each press cycles through selected louvers: -1 → -2 → -3 → -4 → -0 (where -0 indicates all four louvers are selected). The system exits louver setting mode after 10 seconds of inactivity.

Press the SWING button to start/stop the auto swing feature of the selected louvers.

Swing function

Press the SWING button. The horizontal louver auto swing feature is energized. Press again to stop it.

FP function

Press this button twice within one second under HEAT Mode with the temperature set to 16°C. The unit will operate at high fan speed (while the compressor is on) with the temperature automatically set to 8°C. This function is for heat pump air conditioners only. Pressing ON/OFF, Sleep, Mode, Fan, or Temp. buttons during operation will cancel this function.

ECO/GEAR function

Press this button to enter energy-efficient modes: ECO → GEAR (75%) → GEAR (50%) → Previous setting mode → ECO...

ECO operation:

Under cooling mode, pressing this button adjusts the temperature to 24°C and sets the fan speed to Auto to save energy (if the set temperature is less than 24°C). If the set temperature is above 24°C, the fan speed changes to Auto, and the set temperature remains unchanged.

NOTE: Pressing this button, modifying the mode, or adjusting the set temperature to less than 24°C / 75°F will stop ECO operation. For optimal cooling, the set temperature should be 24°C or above. If uncomfortable, press the ECO button again to stop it.

GEAR operation:

Press this button to enter GEAR operation: 75% (up to 75% electrical energy consumption) → 50% (up to 50% electrical energy consumption) → Previous setting mode. Under GEAR operation, the display alternates between electrical energy consumption and set temperature.

Silence function

Keep pressing the FAN button for more than 2 seconds to activate/disable the Silence function. Due to low-frequency compressor operation, this may result in insufficient cooling and heating capacity. Pressing ON/OFF, Mode, Sleep, Boost, or Clean buttons during operation will cancel the silence function.

LOCK function

Press the BOOST and VANE buttons simultaneously for more than 5 seconds to activate Lock function. All buttons will be unresponsive except for these two buttons, which can be pressed again for two seconds to disable locking.

SET function

Press the SET button to enter function setting. Then, press the SET button or TEMP [up arrow]/[down arrow] button to select the desired function. The selected symbol flashes on the display; press OK to confirm.

To cancel a selected function, repeat the same procedures. Press the SET button to scroll through operation functions: Active clean [icon] → Fresh* [icon] → Sleep [icon] → Follow Me [icon] → AP mode* [icon] → Active clean... [*]: Model dependent.

Active clean function [icon] (some units)

The Active Clean Technology washes away dust, mold, and grease that cause odors by automatically freezing and thawing frost on the heat exchanger. When this function is on, the indoor unit displays "CL". After 20 to 45 minutes, the unit turns off automatically and cancels the CLEAN function.

Sleep function [icon]

The SLEEP function reduces energy use during sleep when different temperature settings are needed. This function can only be activated via the remote control. For details, see sleep operation in the "USER'S MANUAL". Note: The SLEEP function is not available in FAN or DRY mode.

FRESH function [icon] (some units)

When the FRESH function is initiated, the ion generator energizes to help purify the air in the room.

Follow me function [icon]

The FOLLOW ME function allows the remote control to measure the ambient temperature at its location and send this signal to the air conditioner every 3 minutes. When using AUTO, COOL, or HEAT modes, measuring ambient temperature from the remote control (instead of the indoor unit) optimizes temperature for maximum comfort.

NOTE:

• Press and hold the BOOST button for seven seconds to start/stop the memory feature of the Follow Me function.
• If the memory feature is activated, "On" displays for 3 seconds.
• If the memory feature is stopped, "OF" displays for 3 seconds.
• While the memory feature is activated, pressing ON/OFF, shifting mode, or a power failure will not cancel the Follow Me function.

AP function [icon] (some units)

Choose AP mode for wireless network configuration. For some units, this may not work by pressing the SET button. To enter AP mode, continuously press the LED button seven times within 10 seconds.