Sealey - Leading Professional Tool & Workshop Equipment Supplier
User Manual for SEALEY models including: FH2010.V2 2000W Fan Heater with Thermostat, FH2010.V2, 2000W Fan Heater with Thermostat, Fan Heater with Thermostat, Heater with Thermostat, Thermostat, Heater
FAN HEATER 2000W 2 HEAT SETTINGS WITH THERMOSTAT
File Info : application/pdf, 3 Pages, 296.36KB
DocumentDocumentFAN HEATER 2000W 2 HEAT SETTINGS WITH THERMOSTAT MODEL NO: FH2010.V2 Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE. Refer to Indoor use only instruction manual DO NOT cover 1. SAFETY THIS PRODUCT IS ONLY SUITABLE FOR WELL INSULATED AREAS OR OCCASIONAL USE. 1.1. ELECTRICAL SAFETY WARNING! It is the user's responsibility to check the following: 9 Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical products. Electrical safety information. It is important that the following information is read and understood: 9 Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. 9 Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct fuse. 8 DO NOT pull or carry the appliance by the power cable. 8 DO NOT pull the plug from the socket by the cable. 8 DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or is replaced immediately by a qualified electrician. If the cable or plug is damaged during use, switch off the electricity supply and remove from use. Ensure that repairs are carried out by a qualified electrician. If an extension reel is used it should be as short as possible and fully unwound before connection. A reel with an RCD fitted is preferred since any appliance plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use of 2.5mm² section cable. 1.2. GENERAL SAFETY WARNING! Disconnect the heater from the mains power, before servicing or performing any maintenance. Servicing or maintenance must only be carried out by an authorised service agent. 9 Check that the heater is in sound condition and good working order. Take immediate action to repair or replace damaged parts. WARNING! DO NOT use the heater near flammable material, liquids, solids, gases or compressed gas cylinders etc. 8 DO NOT allow any untrained or incompetent persons use the heater. Ensure they are familiar with the controls and hazards of the heater. 8 DO NOT use this heater in the immediate surroundings of a bath, a shower or a swimming pool. WARNING! DO NOT use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided. WARNING! To reduce the risk of fire, keep textiles, curtains, or any other flammable material to a minimum distance of 1m from the air outlet. 8 DO NOT use this heater if it has been dropped. 8 DO NOT use if there are visible signs of damage to the heater. 9 Use this heater on a horizontal and stable surface, or fix it to a wall as applicable. 8 DO NOT allow children to touch or to operate the heater 8 DO NOT obstruct the air inlet or outlet on the heater. 8 DO NOT cover the heater. 8 DO NOT operate the heater when you are tired or under the influence of alcohol, drugs or intoxicating medication. 8 DO NOT touch the heater casing or grill when first switched off as these are hot and will take time to cool. 8 DO NOT use the heater for anything other than its intended purpose. It is not suitable for drying clothes or laundry. 8 DO NOT place the heater close to a bath, wash basin, shower, swimming pool or any other water-filled area or wet surface. 8 DO NOT get the heater wet or use in areas of high condensation. 8 DO NOT place the heater up against any surface such as a wall, door or furniture etc. 8 DO NOT place the heater immediately below any electrical outlet. 8 DO NOT allow the power lead to lie in front of the heater outlet. 8 DO NOT attempt to repair a damaged heater, contact an authorised service agent. 8 DO NOT stand on the heater. 8 DO NOT connect the fan heater to a timer device or other equipment that can automatically switch the heater on or off. 9 Ensure that the heater is correctly turned off when not in use and store in a safe, dry area, out of reach of children. © Jack Sealey Limited Original Language Version FH2010.V2 Issue:6 (1) 07/11/23 NOTE: Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance. Children of less than 3 years should be kept away unless continuously supervised. 2. i INTRODUCTION Tough composite case with integral carry handle. Can be seated in a vertical or horizontal position. 2-Position heat settings control two 1000W heating elements. Full range ambient room thermostat maintains temperature at preset level. Fan doubles as cool air blower for use in the summer. Supplied with 3-pin plug. 3. i SPECIFICATION Model ..................................................................... FH2010.V2 Voltage: ............................................................................ 230V Power: .................................................................. 1000/2000W Dimensions:............................................... 230 x 240 x 120mm 4. OPERATION 1000W FAN ONLY 2000W LAMP LIGHTS WHEN HEATER OPERATING MIN 4.1. Position heater where required, either horizontally or vertically on a level surface ensuring that the air intake and outlet are MAX not obstructed in any way. 4.2. Plug the heater into the mains supply. 4.3. Set the thermostat knob to the half way position as shown in fig.1 fig.1. THERMOSTATIC TEMPERATURE CONTROL 4.4. The fan heater will switch on when the selector switch is set to one of the two power settings (1000W or 2000W). 4.5. Once the room reaches the set temperature the heater will switch on and off automatically to maintain that temperature. Adjust the position of the thermostat knob to obtain a comfortable room temperature. 4.6. If the fan fails to operate when a power setting is selected the thermostatic temperature control may be set too low. Turn the knob slowly towards max until the fan starts. 4.7. For a cooling effect turn the selector switch to the fan only setting. 5. MAINTENANCE WARNING! Before attempting any maintenance ensure the unit is unplugged from the mains power supply and that it is cool. 5.1. Clean the heater with a soft dry cloth. DO NOT use abrasives or solvents. 5.2. Periodically check the heater grille to ensure it is not blocked. NOTE: This heater is fitted with a safety device which will cut the power should the heater overheat. If this happens you should disconnect the heater from the mains supply for a minimum of 3 minutes allowing the heater to cool, ensure the heater is not covered or anything is obstructing the vents. Plug the heater back into the electrical socket and switch the heater back on. 5.3. No other maintenance is necessary. If you experience a problem with your heater or if the power lead or plug is damaged contact your local authorised service agent for repair. DO NOT dismantle or tamper with the heater as this may be dangerous and will invalidate your warranty. Parts support is available for this product. Please email sales@sealey.co.uk or telephone 01284 757500 WEEE REGULATIONS Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information. REGISTER YOUR PURCHASE HERE ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations. Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team on technical@sealey.co.uk or 01284 757505. Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 sales@sealey.co.uk www.sealey.co.uk © Jack Sealey Limited Original Language Version FH2010.V2 Issue:6 (1) 07/11/23 Information requirements for electric local space heaters Model identifier(s): FH2010.V2 Item Symbol Nominal heat output Heat output Pnom Minimum heat output (indicative)* * Enter figure or NA Maximum continuous heat output Pmin Pmax,c Value Unit Item Unit 1.8-2.0 kW 0.015 kW 2.0 kW Type of heat input, for electric storage local space heaters only (select one) Manual heat charge control, with integrated thermostat Yes No Manual heat charge control with room and/or outdoor temperature feedback Yes No Electronic heat charge control with room and/or outdoor temperature feedback Yes No Fan assisted heat output Yes No Auxiliary electricity consumption At nominal heat output elmax At minimum heat output elmin In standby mode elSB Type of heat output/room temperature control (select one) Single stage heat output and no room kW temperature control kW Two or more manual stages, no room temperature control kW With mechanic thermostat room temperature control With electronic room temperature control Yes No Yes No Yes No Yes No Electronic room temperature control plus day timer Electronic room temperature control plus week timer Yes No Yes No Other control options (multiple selections possible) Room temperature control, with presence Yes No detection Room temperature control, with open window detection Yes No With distance control option Yes No With adaptive start control Yes No With working time limitation Yes No With black bulb sensor Yes No Contact details: Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk, IP32 7AR. www.sealey.co.uk v1 ERP Table 2