User Guide for ZKTECO models including: C2-260 inBio2-260, Access Controller, C2-260, inBio2-260 Access Controller, C2-260 inBio2-260 Access Controller
◁ Мережевий контролер доступу ZKTeco C2-260 купити за оптовими цінами в DEPS
Safety Precautions Do not expose to direct sunlight, water, dust and soot. Do not place any magnetic objects near the product. Magnetic objects such as magnets, CRT, T V, monitors or speakers may damage the device. Do not place the device near any heating equipment. Prevent water, drinks or chemicals leaking into the device. This product is not intended for use by children unless they are ...
Quick Start Guide C2-260/inBio2-260 Access Controller Version: 1.1 Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the actual product and the written information in this manual. What's in the Box NC COM NO SEN GND BUT NC COM NO SEN GND BUT NC COM NO NC COM NO AUX GND AUX LOCK1 LOCK2 AUX OUT AUX IN PWR RUN TCP/IP RS485 DIP RS485 READER VOUT POWER GND 485B 485A 12VRD GND 485B 485A +12V GND +12V GND C2-260 / inBio2-260 4 Screws & Anchors 2 Screwdrivers 1 4 Diodes Safety Precautions The following precautions are to ensure user's safety and prevent any damage. Please read the instructions carefully before installation. Do not expose to direct sunlight, water, dust and soot. Do not place any magnetic objects near the product. Magnetic objects such as magnets, CRT, T V, monitors or speakers may damage the device. Do not place the device near any heating equipment. Prevent water, drinks or chemicals leaking into the device. This product is not intended for use by children unless they are supervised. Do not drop or damage the device. Do not disassemble, repair or modify the device. Do not Remove dust or dirts regularly. While cleaning, wipe the dust off with a smooth cloth or towel instead of water. Contact your supplier in case of any query. 2 Product PIN Diagram 2 Lock & Door Sensor 2 Aux Output 2 Aux Input NC COM NO SEN GND BUT NC COM NO SEN GND BUT NC COM NO NC COM NO AUX GND AUX LOCK1 LOCK2 AUX OUT AUX IN PWR RUN TCP/IP RS485 DIP RS485 READER VOUT POWER GND 485B 485A 12VRD GND 485B 485A +12V GND +12V GND 12V Power in 12V Power out RS485 Reader RS485 Communication DIP Switch USB Port Ethernet Port Figure 1 3 LED Indicators Figure 2 PWR Figure 3 RUN Figure 4 TCP/IP Figure 5 LINK Solid Green LED indicates TCP/IP communication is normal. Flashing (ACT )Yellow LED indicates data communication is in progress. Solid (POWER) Red LED indicates the panel is powered on. Slowly flashing Green LED indicates normal working status of the system. TCP/IP continuously flashing Yellow LED indicates data transmission. TCP/IP slowly flashing Yellow LED indicates real-time monitoring status. 4 Panel Installation Wall Mounting NC COM NO SEN GND BUT NC COM NO SEN GND BUT NC COM NO NC COM NO AUX GND AUX LOCK1 LOCK2 AUX OUT AUX IN PWR RUN TCP/IP RS485 DIP RS485 READER VOUT POWER GND 485B 485A 12VRD GND 485B 485A +12V GND +12V GND Step 1 Drill holes on the wall Figure 6 Step 2 Fix the device with four screws Rail Mounting Step 1 Fix the guide rail on the wall Figure 7 5 Step 2 Fix the device to the rail mounting. 7 Panel Installation Normally Close Lock Normally Open Lock Exit Button IR Sensor Floodlight Detector FIRE ALARM EKLY PUS H TOTESTWE HTOTESTWE EKLY PUS NC COM NO SEN GND BUT NC COM NO SEN GND BUT NC COM NO NC COM NO AUX GND AUX LOCK1 LOCK2 AUX OUT AUX IN PWR RUN TCP/IP RS485 DIP RS485 READER VOUT POWER GND 485B 485A 12VRD GND 485B 485A +12V GND +12V GND RS485 Ethernet Cable 485 Convertor RS485 Reader 12V DC Power Supply Figure 8 The auxiliary input may be connected to infrared body detectors, fire alarms, or smoke detectors. The auxiliary output may be connected to alarms, cameras or door bells, etc. 6 Installation Diagram Ethernet Communication wire 220/110 V Input Outdoor RS485 reader RS485 Communication wire C2-260/inBio2-260 Access Control Bundle CEILING Sensor Electric Lock Exit Button Indoor RS485 reader OUTDOOR Figure 9 7 INDOOR RS485 Readers Connection NC COM NO SEN GND BUT NC COM NO NC COM NO AUX GND AUX BUT GND SEN NO COM NC LOCK1 LOCK2 AUX OUT AUX IN PWR RUN TCP/IP RS485 DIP RS485 READER VOUT POWER GND 485B 485A 12VRD GND 485B 485A +12V GND +12V GND C2-260 / inBio2-260 DC12V TCP/IP Router 485A 485B GND +12V #1Reader #2Reader #3Reader FR1200 (inBio2-260) Note: 1. It's recommended to connect maximum four readers to one C2-260/inBio2-260. 2. A single RS485 reader interface can supply a maximum of 750 mA (12V) current. So the entire current consumption should be less than this max value when the readers share the power with the panel. 3. Only inBio2-260 supports connection with FR1200 readers. 8 Additional Modules of RS485 Connection with DM10 NC COM NO SEN GND BUT NC COM NO NC COM NO AUX GND AUX BUT GND SEN NO COM NC LOCK1 LOCK2 AUX OUT AUX IN PWR RUN TCP/IP RS485 DIP RS485 READER VOUT POWER GND 485B 485A 12VRD GND 485B 485A +12V GND +12V GND C2-260 / inBio2-260 DC12V TCP/IP Router 485A 485B GND DM10 DC12V DM10 Note: 1. A C2-260/inBio2-260 can connect to maximum eight DM10 modules.. 2. Each DM10 module requires a separate power supply. DC12V 9 Connection with AUX485 NC COM NO SEN GND BUT NC COM NO NC COM NO AUX GND AUX BUT GND SEN NO COM NC LOCK1 LOCK2 AUX OUT AUX IN PWR RUN TCP/IP RS485 DIP RS485 READER VOUT POWER GND 485B 485A 12VRD GND 485B 485A +12V GND +12V GND C2-260 / inBio2-260 DC12V TCP/IP Router DC12V DC12V 485A 485B GND AUX Input Device AUX485 AUX485 Note: 1. A C2-260/inBio2-260 can connect to maximum two AUX485 modules. 2. Each AUX485 module can connect to maximum four auxiliary devices. 3. Each AUX485 module requires a separate power supply. AUX Input Device 9 Connection with WR485 NC COM NO SEN GND BUT NC COM NO NC COM NO AUX GND AUX BUT GND SEN NO COM NC LOCK1 LOCK2 AUX OUT AUX IN PWR RUN TCP/IP RS485 DIP RS485 READER VOUT POWER GND 485B 485A 12VRD GND 485B 485A +12V GND +12V GND C2-260 / inBio2-260 DC12V TCP/IP Router 485A 485B GND +12V WR485 WR485 Note: 1. A C2-260/inBio2-260 can connect to maximum four WR485 modules. 10 Connection to ZKBioAccess Software Here the connection between C2-260/inBio2-260 and AUX485 is used as an example to illustrate the software settings. After proper wiring, perform the following steps: 1. Set the RS485 address of AUX485 from 1-15. 2. Inclusion of C2-260/inBio2-260 to software: Open the ZKBioAccess Software. Click [Access] > [Device] > [Device] > [New], enter the relevant information, and then click [OK]. Step 2 Step 1 S tep 3 Step 4 After adding successfully, the TCP/IP indicator of inBio2-260 flashes every two seconds, indicating the communication is normal. 3. Inclusion of AUX485 module to the software: Click [Device] > [I/O Board] > [New], enter the name and RS485 address of AUX485, and then click [OK]. 11 4. Click [Device] > [Auxiliary Input] to view all the auxiliary inputs. Note: For other specific operations, please refer to ZKBioAccess User Manual. 12 Specifications Model Number of Doors Supported by Default Number of Auxiliary Inputs Number of Auxiliary Outputs RS485 Extension Port RS485 Reader Port Number of Readers Supported Types of Readers Supported DM10 (Single-Door Extension Board) (Optional) AUX485 (RS485-4 Aux. IN Converter) (Optional) WR485 (RS485-Weigand Converter) (Optional) Card Capacity Log Capacity Communication CPU RAM Power Dimensions (L*W*H) Operating Temperature Operating Humidity C2-260 2 2 2 1 1 4 RS485 card reader, Wiegand reader (WR485) Max. 8 2 4 30,000 200,000 TCP/IP, RS458 32-bit 1.0GHz 64MB 9.6V - 14.4V DC 116.47*96.49*31.40 mm -10°C to 50°C / 14°F to 122°F 20% to 80% ZKTeco Industrial Park, No. 26, 188 Industrial Road, Tangxia Town, Dongguan, China. Phone : +86769-82109991 Fax : +86755-89602394 www.zkteco.com Copyright © 2020 ZKTECO CO., LTD. All Rights Reserved.Adobe Illustrator CC (Windows) www.ilovepdf.com