Index of /
Instruction Manual for cartell models including: CP-4 Automatic Gate Opener, CP-4, Automatic Gate Opener, Gate Opener
Index of /store/pdfs
File Info : application/pdf, 2 Pages, 1.30MB
DocumentDocumentINSTALLATION INSTRUCTIONS FOR CP-4 AUTOMATIC GATE OPENER* 1. SERIAL NUMBER There is a barcode serial number on the bottom of "puck" and on the product box. When calling to talk about your product, please have this number handy. PRODUCT CODE YEAR SERIAL MADE NUMBER 4. CONNECT TO GATE CP-4 works with all gate operatorspowered or solar. Connect wires as follows: POWER GATES SOLAR GATES RED POWER + RED POWER + BLACK WHITE BLUE YELLOW POWER BLACK COMMON WHITE EXIT N.O. BLUE EXIT N.C. GND or COM FREE EXIT or OPEN TERMINAL VOLTAGE CURRENT 8-24 VAC 8-30 VDC Standby: 30-70 µA Alarm: 40-60 mA 2. TRENCH PIPE & CABLE Trench 1/2" PVC pipe beside driveway to where CP-4 will be buried, and pull cable inside conduit (may need wire lubricant). 12' 80' - 100' NOTE: Warranty voided if cable not run in conduit 5. TEST SENSITIVITY NOTE: IN MOST CASES SENSITIVITY WILL NOT NEED TO BE ADJUSTED. SENSITIVITY ADJUSTMENT HIGH (Default) Detects vehicle 12-14' 1 & 2 in OFF position ON 12 MEDIUM Detects vehicle 6-8' 1 ON & 2 OFF position ON 12 LOW Detects vehicle 2-3' 1 & 2 in ON position ON 12 Note: Dip switch color may vary 3. CONDUIT & SLIP JOINT 6. BURY CONDUIT & "PUCK" After pulling cable through plastic conduit, insert conduit inside slip joint on "puck." DO NOT GLUE (to un-install later, if needed). Test unit with gate by swinging steel over puck (or driving vehicle by). If it opens the gate correctly, finish installation by burying conduit and puck 3-5" below surface. www.LinearGateOpeners.com | (800) 878-7829 | Sales@LinearGateOpeners.com OTHER INSTRUCTIONS · CP-4 may be installed above ground by screwing "puck" directly to post or building · If above ground, make sure puck is immovable to eliminate false alarms · If installed above ground, conduit is required to mechanically protect cable (animals will eat) Install CP-4 at least: · 6-10 feet away from buried power, telephone, or invisible dog fence · 10 feet away from natural gas lines · 20 feet away from power pole with a transformer · 100 feet back from railroad traffic · 200 feet away from high power substation power lines · 80-100 feet back from gate operator Technical Specifications Power Required 824 VAC or 830 VDC Stand-By Current 3070 Microamps (A) Alarm Current 3040 Milliamps (mA) Relay Time 23 seconds Relay Contacts Relay Contact Rating SPDT, floating, N.O. or N.C. (Form C) 1 amp/24 VDC (1 mA at 5 VDC min. load) Enclosure Rating IP67 Strength Rating Temperature Range 9.53 ton-force 8646 kgf -25° F. +140° F. -32° C. 60° C. Dimensions 4.5 in. dia. x 2.5 in. high Weight 5 lbs. with 100 ft. cable RETURNING MERCHANDISE CONSUMER: Contact us at (800) 878-7829 INSTALLER: CALL BEFORE DIGGING UP Call u s to troubleshoot and receive a Return Merchandise Authorization (R.M.A.) number. Write R.M.A. number on return shipping box and any correspondence included with defective product. 5 YEAR WARRANTY All Cartell products are warranted against defects in material and workmanship for five RANTY Y WARRA years. This warranty does not cover defects caused by, but not limited to: acts of God, WARRANT Y E A R NTY WAR improper installation, abuse, fire damage, electrical surges, and damage to cable caused by slicing, pulling, tangling, improper splicing or not running in non-metalic conduit. The CP-4 complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. www.LinearGateOpeners.com | (800) 878-7829 | Sales@LinearGateOpeners.com