Lampa LED VIDEX

General Description

The Videx LED lamp is a high-tech light source designed for use in industrial sectors, public utility buildings, and domestic plots. It is characterized by high resistance to external factors and a wide range of operating temperatures and voltages. After installation, it requires no maintenance throughout its entire service life.

• The light source uses LED diodes, ensuring high lighting quality.
• It offers significant electricity savings compared to alternative light sources.
• The lamp is resistant to a high number of on/off cycles.
• It can be used in both low and high temperatures.
• It reduces operating costs by not requiring maintenance or replacement of consumable parts.
• The lamp is durable and possesses a high degree of protection against negative environmental influences.

Specifications

Technical data such as Article (INDEX), Power (W), color temperature (K), luminous flux (Lm), color rendering index (Ra), voltage (V), frequency (Hz), power factor, current (mA), lifespan (h), protection class (IP), operating temperature (°C), impact resistance class (IK), housing color, diffuser type, overall dimensions, and warranty period (year) are provided on the packaging.

• No UV and IR radiation.
• Maximum projection area of the lamp exposed to wind impact: 0.01 m².
• Light intensity curve: D.
• Protection class against electric shock: Class I.
• Light distribution class: P.

Product meets the requirements of:

• DSTU EN IEC 55015:2021
• DSTU EN 61000-3-2:2016
• DSTU EN 61000-3-3:2017
• DSTU EN 61547:2016
• DSTU EN 50581:2014
• DSTU EN 62321:2014
• DSTU EN 60598-1:2017
• DSTU EN 60598-2-3:2014
• DSTU EN 60598-2-5:2018
• DSTU EN 62612:2017
• DSTU EN IEC 62031:2022

Does not require disposal with municipal waste. Does not require mandatory certification. Shelf life before use is unlimited.

Set Contents

1. LED Lamp.
2. User Manual.
3. Mounting tool kit.
4. Cardboard packaging.

Safety Requirements

[!] Connection and mounting should only be performed by qualified specialists in accordance with PUE requirements, safety regulations for electrical installations, and after reading this manual.

The lamp is designed for outdoor installation. It is protected against dust and water splashes ([IP54 rated]).

The parameters of the network to which the lamp is connected must correspond to the parameters indicated on the packaging.

• All assembly or disassembly work should be carried out only after disconnecting the power supply [power disconnected].
• Do not disassemble lamp components or make changes to its construction.
• Do not connect the lamp with the housing disassembled or the electrical installation exposed.
• Do not operate the LED lamp if it has mechanical damage.

Installation Recommendations

• Before operation: Ensure the luminaire's temperature has reached the ambient temperature where it will be used.
• Power Disconnection: Disconnect the electrical power supply before mounting (Fig. 1).
  Fig. 1: Illustration shows a hand operating a circuit breaker switch labeled "~220V OFF", indicating the disconnection of power.
• Removing the Housing: Remove the front part of the housing (Fig. 2).
  Fig. 2: Diagram depicts the process of removing the front cover of the LED lamp.
• Mounting the Luminaire: Mount the luminaire using the mounting elements included in the set.
• Electrical Connection: Connect the luminaire to the electrical installation using a terminal block, and then re-install the protective cover (Fig. 3).
  Fig. 3: A wiring diagram showing the connection points for the lamp. It illustrates the L (Live), N (Neutral), and Ground terminals, with wires labeled "Brown", "Blue", and "Yellow-green" connecting to them.
• Powering On: Restore the electrical power supply (Fig. 4).
  Fig. 4: Illustration shows a hand operating a circuit breaker switch labeled "~220V ON", indicating the restoration of power.

Connection Recommendations

Connecting the LED lamp is permissible only to a functional electrical installation. Damaged electrical installations must be replaced. The connection and insulation of the electrical installation wires with the lamp wires should be performed according to the proposed diagram, following PUE requirements. The lamp should be connected to the power supply network using a screw-type terminal block (Fig. 3). Operating the LED lamp with a damaged installation or connection points is prohibited.

Maintenance and Care

The LED lamp does not require technical maintenance. Lamp care is permitted only after disconnecting the power supply [power disconnected]. Ensure the lamp housing has cooled down [ensure housing has cooled].

For cleaning the external surface of the housing, a dry, clean cloth can be used [clean with dry cloth].

Do not use liquids or abrasive materials or cleaning agents [do not use liquids or abrasive cleaners].

Never disassemble the lamp or its components [do not disassemble].

Storage and Transport

The LED lamp should be stored and transported in the manufacturer's packaging. During storage, the following conditions should be observed: ambient temperature – from -25°C to +40°C; relative humidity – not more than 80% at a temperature of +25°C. The storage period is unlimited, provided these conditions are observed.

Warranty Obligations

The warranty period for the LED lamp is indicated on the packaging. Product replacement and return are possible if the requirements for transport, storage, and operation specified in this manual are met.

Warranty obligations do not cover the product if:

• The lamp shows signs of mechanical damage;
• There are signs of a short circuit;
• The seller's receipt is missing;
• The packaging is absent or its condition prevents safe transport of the LED lamp;
• The operating, transport, or storage conditions have been violated.

Environmental Protection

In accordance with WEEE Directive, it is forbidden to dispose of used equipment marked with a crossed-out bin symbol [crossed-out bin symbol] with other waste. The user, wishing to dispose of electronic and electrical equipment, is obliged to hand it over to a collection point for used equipment. The equipment does not contain hazardous components that have a particularly negative impact on the environment and human health. The manufacturer is not responsible for damages resulting from non-compliance with these instructions. The manufacturer reserves the right to update this manual.

Importer and Producer Information

Importer: Allegro opt Sp. z o.o. ul. Mierzeja Wiślana 11, 30-732 Krakow, Poland. Made in China/Wyprodukowano w Chinach. Visit: www.videx.com.pl

Producer/Producent: Allegro-opt PE, 106-ZH Heroiv Mariupolia street, Kropyvnytskyi, 25004, Ukraine.

Certifications: CE [CE marking], Recycling symbol [recycling symbol].