VIDEX VL-AR Series LED Fixtures
User Manual and Technical Specifications
Product Overview
The VIDEX LED lamp is an advanced technological light source. Designed for lighting park areas and enclosures. It features a high degree of resistance to external influences, a wide range of operating temperatures and voltages. Easy to operate and replace the light source.
- Enables significantly more economical use of electrical energy compared to alternative light sources.
- Resistant to a large number of on/off cycles.
- Can be used in both low and high temperatures.
- Long-lasting, possesses a high degree of protection against negative environmental influences.
Technical Specifications
| Article | Power (W) | Dimensions (mm) | Weight (g) | Material |
|---|---|---|---|---|
| VL-AR011G | 50W Max | 81*68*92 | 350±10% | Aluminium |
| VL-AR012G | 50W Max x 2 | 150*68*92 | 600±10% | Aluminium |
| VL-AR021B | 50W Max | 81*68*92 | 250±10% | Aluminium |
| VL-AR022B | 50W Max x 2 | 150*68*92 | 430±10% | Aluminium |
| VL-AR071G | 50W Max | 80*112*154 | 650±10% | Aluminium, Polycarbonate |
| VL-AR072G | 50W Max x 2 | 80*112*225 | 820±10% | Aluminium, Polycarbonate |
General specifications: Operating temperature (°C), grounding availability, impact resistance class (IK), housing color, housing material, overall dimensions, and warranty period (years) are provided on the packaging. No UV or IR radiation. Maximum projected surface area of the lamp exposed to wind is 0.01 m². Light distribution curve - D. Electrical shock protection class - Class I. Light distribution class - P.
Product meets requirements: DSTU EN IEC 55015:2021, DSTU EN 61000-3-2:2016, DSTU EN 61000-3-3:2017, DSTU EN 61547:2016, DSTU EN 50581:2014, DSTU EN 62321:2014, DSTU EN 60598-1:2017, DSTU EN 60598-2-3:2014, DSTU EN 60598-2-5:2018, DSTU EN 62612:2017, DSTU EN IEC 62031:2022. Not to be disposed of with municipal waste. Not subject to mandatory certification. Shelf life is unlimited.
Package Contents
- LED Lamp (lamp not included in the set).
- Mounting kit.
- Instruction manual.
- Packaging box.
Safety Requirements
- Connections and installation should only be performed by qualified specialists in accordance with PUE requirements, safety regulations for consumer electrical installations, and after familiarizing themselves with this manual.
- The lamp is intended for outdoor placement.
- Protection against dust and water splashes (IP54).
- The parameters of the network to which the lamp is connected must comply with the parameters indicated on the packaging.
- All assembly or disassembly work must be carried out exclusively with the electrical installation power disconnected.
- Disassembly of the lamp or making changes to its construction is prohibited.
- Do not connect the lamp with the housing removed or exposed electrical wires.
- Operation of the LED lamp with mechanical damage is prohibited.
Connection Recommendations
Connecting the LED lamp is permitted only to a working electrical wire. Damaged wiring must be replaced. Electrical wire connections and insulation with the lamp wires should be made according to the proposed diagram, following PUE requirements. The lamp should be connected to the power supply using a screw terminal block (Fig. 2.2). Using the LED lamp with damaged wiring or connection points is prohibited.
[Power symbol] ~220V OFF
For models: VL-AR011G, VL-AR012B, VL-AR021G, VL-AR022B
Diagram 2.1 shows connections for L (Brown wire), N (Blue wire), and Ground (Yellow-Green wire) to a terminal block (Diagram 2.2).
For models: VL-AR071G, VL-AR072G
Diagram 2.1 shows similar connections for L (Brown wire), N (Blue wire), and Ground (Yellow-Green wire) to a terminal block (Diagram 2.2).
[Power symbol] ~220V ON
Storage and Transport
The LED lamp should be stored in the manufacturer's packaging, in a ventilated room, at temperatures from -25°C to +40°C and humidity not exceeding 80% (at +25°C). The product is transported exclusively in the manufacturer's packaging and in covered transport, maintaining storage conditions. At the same time, their stable position must be ensured, which excludes falls, impacts, and other mechanical damage. The storage period is unlimited if the above conditions are met.
Maintenance and Care
The LED lamp does not require maintenance. Lamp maintenance is only permitted after disconnecting the power supply.
- Ensure the housing has cooled down.
- A dry, clean cloth can be used to clean the outer surface of the housing.
- The use of liquids, materials, or abrasive agents is prohibited.
- Never disassemble the LED lamp or its components.
Warranty Obligations
The warranty period for the LED lamp is indicated on the packaging. Product replacement and return are possible if the transport, storage, and operation requirements proposed in this manual are followed.
Warranty obligations do not apply to the product if:
- The lamp has been disassembled or shows signs of mechanical damage;
- Signs of short circuits are visible on the wires;
- There is no check from the seller organization;
- Lack of packaging or its condition prevents safe transport of the product;
- Violation of operating, transport, and storage conditions.
Environmental Protection
In accordance with WEEE Act regulations, it is prohibited to dispose of used equipment marked with the symbol of a crossed-out bin along with other waste. A user wishing to dispose of electronic and electrical equipment is obliged to return it to a collection point for used equipment. The equipment does not contain hazardous components that have a particularly negative impact on the environment and human health. The manufacturer is not responsible for damages resulting from non-compliance with the above instructions. The manufacturer reserves the right to make updates to this manual.
According to WEEE directive, do not dispose of with municipal waste. Return used equipment to collection points. [Crossed-out trash bin] ?️❌
