FSP FSP0XX-DF(W)AN3 Series 30W-50W POE Application Adapter

Technical Datasheet

FSP0XX-DF(W)AN3 Series

Features

Meets IEC 62368-1 & IEC 60950-1
Meets Energy Efficiency DOE Level VI
Meets Code of Conduct Version 5 Tier 2
High Reliability
EMC Standard: EN55032/ EN55024 Class B
Over Current Protection
Over Temperature Protection
Over Voltage Protection

Safety Standard Approval

CULUS LISTED I.T.E. POWER SUPPLY E190414
TÜV Rheinland ZERTIFIZIERT (ID 1000000000)
Tested to Comply With FCC Standards
FOR HOME OR OFFICE USE

Image of a compact, black AC to DC power adapter with a standard AC input connector.

Description

This product is a 30~50 watt AC to DC adapter intended for use in Consumer Electronic Systems that have small wattage demands. This adapter operates at 90 to 264 VAC input voltage. The unit meets CISPR32 EN55032 CLASS B, EN55024 and FCC PART 15B Class B emission limits, and is designed for ITE application.

Input Specifications

Input voltage: 90-264 VAC
Input frequency: 47-63 Hz
Input current: ≤ 1.2A (100Vac, 240Vac / full load)
No load power consumption: ≤ 0.075W (115Vac, 230Vac)
Touch current: ≤ 0.25mA (264Vac / 50Hz)

Output Specifications

Output voltage/current: See rating chart
Total output power: See rating chart

Protection Features

Over voltage: The adapter will enter into shut down (no output) if over voltage occurs at the output terminal due to an internal fault. The output trip voltage shall not exceed 63 Vdc. Normal state is restored by AC reset.
Short circuit & Over current: When an internal or external fault is applied to the output, the power supply shall shut down and enter auto-recovery mode.
Over temperature: The power supply will enter into shut down when abnormal thermal rise occurs. Normal state is restored by AC reset.
Brown-out: Set at 50Vac~60Vac

Environmental Specifications

Working TEMP.: 0~70°C (de-rating > 40°C)
Storage TEMP.: -20~+80°C
Working Humidity: 20~80% RH non-condensing
Storage Humidity: 10~90% RH non-condensing

Input Specifications (Performance)

Efficiency: See rating chart.
Power turn-on time: ≤ 3 Sec (At 100Vac / full load, output voltage shall remain regulation)
Hold-up time: ≥ 8ms (At 100Vac or 240Vac / full load, output voltage shall remain regulation)
Inrush current: Shall be less than the rating of adapter critical component (including rectifiers, fuse surge and current limiting device) at 100Vac, 240Vac / full load.
Operating altitude: 5000 meters above sea level
Withstand voltage: Between AC input and secondary applied DC 4242V, test time 1 minute, cut off current shall be less than 10mA.
MTBF: 300,000 hours at 25°C, 100Vac, 240Vac / full load (standard SR332)

EMC Performance

EN55032: Class B conducted, Class B radiated
FCC: Class B conducted, Class B radiated
VCCI: Class B conducted, Class B radiated
EN61000-3-2: Meets class D
EN61000-3-3: Meets regulation
EN61000-4-2: Air discharge: ±8 KV, contact discharge: ±4KV, meets criterion A
EN61000-4-3: 80~1000 MHz, 3V/m, 80% AM(1kHz), meets criterion A
EN61000-4-4: Impulse: ±1kV applied to L,N, meets criterion A
EN61000-4-5: ±1kV applied differential mode, ±2kV applied common mode, meets criterion A
EN61000-4-6: 0.15~80 MHz, 3Vrms, 80% AM(1kHz), meets criterion A
EN61000-4-8: 50 Hz or 60Hz, 1A/m, meets criterion A
EN61000-4-11 Voltage Dips: >95% reduction for 0.5 period, meets criterion B; 30% reduction for 25 period, meets criterion C
Voltage Interruptions: >95% reduction for 250 period, meets criterion C

Power De-rating

For 100Vac or 240Vac input, de-rating applies as follows: 0°C to 40°C at 100% load, 50°C at 85% load, 60°C at 70% load, 70°C at 55% load. (Shall be less than the rating of adapter critical component, follow FSP specification (adapter)).

Performance Curves

Input Voltage Derating Curve

A line graph showing Input Voltage Derating Curve, with Input Voltage (Vac) on the x-axis (ranging from 90 to 264) and % Output Power on the y-axis (ranging from 0 to 100). The curve shows output power decreasing as input voltage increases beyond a certain point.

Output Power Derating Curve

A line graph showing Output Power Derating Curve, with Temperature (°C) on the x-axis (ranging from 0 to 70) and % Max Load on the y-axis (ranging from 0 to 100). The curve shows output power decreasing as temperature increases above 40°C.

Output Voltage/Current Rating Chart

Model	Output Voltage	Output Current	AC Inlet	Efficiency DOE(Level VI)	Efficiency CoC V5 (Tier 2)
FSP030-DFAN3	48V	0.625A	C14	≥86.95%	≥87.70%
FSP030-DWAN3	54V	0.56A	C14	≥86.95%	≥87.70%
FSP040-DFAN3	48V	0.83A	C14	≥87.59%	≥88.59%
FSP040-DWAN3	54V	0.74A	C14	≥87.59%	≥88.59%
FSP050-DFAN3	48V	1.042A	C14	≥88%	≥89.0%
FSP050-DWAN3	54V	0.93A	C14	≥88.0%	≥88.59%

Mechanical Specifications

The main adapter unit has approximate dimensions of 97mm x 50mm x 30mm. It features a black case with a label indicating model and specifications. A cable tie made of PET plated material secures the output cable. The output cable is approximately 1200mm ± 20mm long and uses wire gauge 22AWG. Ferrite components are included as required.

Connector Specifications

The AC input connector is a standard C14 type. The DC output connector is shown with two terminals labeled 'a' (black print white) and 'b' (print edge). The wiring for the output cable uses wire number 2468 with a 22AWG gauge.

	FSP FSP0XX-DF(W)AN3 Series: 30W-50W PoE Application Adapter Technical Datasheet This technical datasheet from FSP Group details the FSP0XX-DF(W)AN3 Series, a range of 30W to 50W Power over Ethernet (PoE) application adapters. Designed for consumer electronic systems and ITE applications, these adapters meet stringent energy efficiency standards like DOE Level VI and CoC V5, alongside safety certifications including IEC 62368-1 and IEC 60950-1. Key features include over-voltage, over-current, and over-temperature protection.
	FSP FSP0XX-DF(W)AN3 Series 30W-50W PoE Application Adapter Datasheet Technical datasheet for the FSP FSP0XX-DF(W)AN3 Series PoE application adapters, detailing specifications, features, safety approvals, and performance characteristics for 30W to 50W power output.
	FSP 30W-50W POE Application Adapter Datasheet Technical datasheet for FSP 30W-50W POE application adapters, including models FSP0XX-DF(W)AN3 series. Details features, specifications, safety approvals, input/output ratings, derating curves, and mechanical dimensions.
	FSP FSP0XX-DF(W)AN3 Series 30W-50W POE Application Adapter Datasheet Technical datasheet for the FSP FSP0XX-DF(W)AN3 series of 30W-50W POE application adapters. Features include compliance with IEC 62368-1, DOE Level VI, and high reliability, with detailed input/output specifications, safety approvals, and environmental ratings.
	FSP Switching Power Adapter CB Test Certificate - Models FSP030-DFAN3, FSP040-DFAN3, FSP050-DFAN3 Official CB Test Certificate for FSP Switching Power Adapters, including models FSP030-DFAN3, FSP030-DWAN3, FSP040-DFAN3, FSP040-DWAN3, FSP050-DFAN3, and FSP050-DWAN3, certified under IEC 62368-1:2014 by TÜV Rheinland Japan Ltd.
	FSP Switching Power Adapter CB Test Certificate - Models FSP030-DFAN3 to FSP050-DWAN3 Official CB Test Certificate issued by TÜV Rheinland Japan Ltd. for FSP Group Inc. Switching Power Adapters, confirming conformity with IEC 62368-1:2018. Includes model numbers FSP030-DFAN3, FSP030-DWAN3, FSP040-DFAN3, FSP040-DWAN3, FSP050-DFAN3, FSP050-DWAN3.
	FSP Switching Power Adapter CB Test Certificate - Models FSP030, FSP040, FSP050 Series Official CB Test Certificate for FSP Group Inc. Switching Power Adapters, including models FSP030-DFAN3, FSP030-DWAN3, FSP040-DFAN3, FSP040-DWAN3, FSP050-DFAN3, and FSP050-DWAN3, certified to IEC 62368-1.
	FSP Switching Power Adapter CB Test Certificate - Models FSP030, FSP040, FSP050 Series Official CB Test Certificate for FSP Group Inc. switching power adapters, covering models FSP030-DFAN3, FSP030-DWAN3, FSP040-DFAN3, FSP040-DWAN3, FSP050-DFAN3, FSP050-DWAN3, certified to IEC 62368-1:2018.