Behringer VIRTUALIZER 3D FX2000 Quick Start Guide

Safety Instructions

General Safety Precautions:

• Read all instructions and heed all warnings.
• Keep these instructions for future reference.
• Do not use this apparatus near water.
• Clean only with a dry cloth.
• Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding-type plug.
• Protect the power cord from being walked on or pinched.
• Use only attachments/accessories specified by the manufacturer.
• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
• Unplug this apparatus during lightning storms or when unused for long periods of time.
• Refer all servicing to qualified service personnel.
• The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.
• Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
• Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. Take it to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE).
• Do not install in a confined space, such as a book case or similar unit.
• Do not place naked flame sources, such as lighted candles, on the apparatus.
• Please keep the environmental aspects of battery disposal in mind. Batteries must be disposed-of at a battery collection point.
• This apparatus may be used in tropical and moderate climates up to 45°C.

Legal Disclaimer: Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners.

Limited Warranty: For the applicable warranty terms and conditions and additional information regarding Music Tribe's Limited Warranty, please see complete details online at musictribe.com/warranty.

Hook-Up

Step 1: Connections

Connecting to an External Effects Processor with Mixing Board:

• Connect the INPUTS 1 and 2 of the FX2000 to the AUX SEND outputs of your mixing board using TRS cables.
• Connect the OUTPUTS 1 and 2 of the FX2000 to the AUX RETURN inputs of your mixing board using TRS cables.
• For MIDI control, connect a MIDI controller (e.g., FCB1010) to the MIDI IN connector of the FX2000.

Connecting to a Guitar Amp Effects Loop:

• Connect the FX2000's INPUT 1 to the SEND output of your guitar amp's effects loop.
• Connect the FX2000's OUTPUT 1 to the RETURN input of your guitar amp's effects loop.

Controls Overview

Front Panel Controls:

• DISPLAY: Shows the effect name, parameter name, and parameter value of the current preset.
• LEVEL METERS: Display the signal level relative to the setting of the OPERATING LEVEL button.
• STATUS LEDs: Indicate the type of value that may currently be edited (e.g., %, dB, Hz, sec).
• PRESET button: Enables the JOG WHEEL to scroll through the 200 presets.
• EFFECT button: Enables the JOG WHEEL to scroll through the 71 basic effect algorithms.
• EDIT button: Selects the function of the EDIT KNOBS. The EDIT LEDs indicate which functions are active.
• EDIT KNOBS (A-F): Adjust various effect parameters, EQ settings, MIDI functions, and INPUT/OUTPUT configurations.
• MIX knob: Adjusts the wet/dry mix of the output signal. Pressing the MIX knob bypasses the processor.
• JOG WHEEL: Scrolls through presets and adjusts parameter values.
• POWER button: Turns the unit on and off.
• STORE button: Saves an altered preset to a desired location.
• COMPARE button: Temporarily restores an altered preset's settings to compare changes to the original sound.
• SETUP button: Enters Setup Mode, enabling the EDIT KNOBS to select categories within MIDI, INPUT, OUTPUT, and CONFIGURATION.

Rear Panel Connections:

• INPUTS 1 & 2: Balanced 1/4" TRS and XLR jacks.
• OUTPUTS 1 & 2: Balanced 1/4" TRS and XLR jacks.
• MIDI IN, MIDI OUT, THRU: 5-pin DIN connectors for MIDI command transmission and reception.
• OPERATING LEVEL button: Switches between -10 dBV and +4 dBu for optimal operating range.
• Mains Connection: Standard IEC receptacle for power input.

Getting Started

1. Make all audio, MIDI, and power connections to the FX2000. Ensure all devices are powered off.
2. Power up the FX2000 first, followed by other connected devices.
3. Turn the MIX knob to adjust the effect's intensity (wet/dry mix). For use with a mixing board, set the MIX knob fully clockwise.
4. Adjust the Send and Return levels on your amplifier or mixer as needed. Ensure the LEVEL METERS on the front panel do not reach the red CLIP LEDs.
5. To select a preset, press the PRESET button, then use the JOG WHEEL to scroll through the available presets.
6. To edit a preset, press the EDIT button, then use the EDIT KNOBS to adjust parameters A-D. Press EDIT again for parameters E, F, and EQ settings.
7. To save an altered preset, press the STORE button, use the JOG WHEEL to select a user preset location, and press STORE again to confirm.
8. Download the full manual from behringer.com for more detailed information on the FX2000's functionality.

Preset Chart

The VIRTUALIZER 3D FX2000 features a comprehensive list of internal (factory) presets and user-defined presets, covering a wide range of effects including reverbs, delays, modulation, filters, distortion, and more. Each preset is categorized by effect type and includes parameters for adjustment.

Specifications

Analog Inputs:

• Connectors: XLR and 1/4" TRS
• Type: RF filtered, servo-balanced input stage
• Impedance: 80 kΩ balanced
• Nominal Operating Level: -10 dBV or +4 dBu (selectable)
• Max. Input Level: +15 dBu at +4 dBu nominal, +1 dBV at -10 dBV nominal

Analog Outputs:

• Connectors: XLR and 1/4" TRS
• Type: Electronically servo-balanced output stage
• Impedance: 80 Ω balanced
• Max. Output Level: +15 dBu at +4 dBu nominal, +1 dBV at -10 dBV nominal

System Specifications:

• Bandwidth: 20 Hz to 20 kHz, +/- 3 dB
• SNR: 91 dB unweighted (20 Hz to 20 kHz)
• THD: 0.018% typ. @ +4 dBu, 1 kHz, 0 dBu input, gain 1
• Crosstalk: < -76 dB

MIDI Interface:

• Type: 5-pin DIN-socket IN/OUT/THRU

Digital Processing:

• Converters: 24-bit Sigma-Delta, 64/128-times oversampling
• Sampling Rate: 46.875 kHz

Display: 4-digit 14-segment alpha-numeric LED-Display

Power Supply:

• Voltage: 100-240 V~, 50-60 Hz
• Fuse: T 200 mA H 250 V (100-120 V~) / T 100 mA L 250 V (200-240 V~)

Power Consumption: 15 Watts max.

Mains Connection: Standard IEC receptacle

Physical:

• Dimensions (H x W x D): 1.75 x 19 x 8.5" / 44.5 x 483 x 217 mm
• Net Weight: approx. 4.2 lbs / 1.9 kg
• Shipping Weight: approx. 7 lbs / 3.2 kg

Other Important Information

Registration: Register your new Music Tribe equipment online at musictribe.com for faster repair claims and warranty information.

Malfunction: If you experience issues, contact your local Music Tribe Authorized Reseller or visit musictribe.com for online support and warranty claim submission.

Power Connections: Ensure correct mains voltage and use only fuses of the same type and rating for replacements.

Federal Communications Commission (FCC) Compliance Information

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CE Compliance

This product is in compliance with Directive 2014/35/EU, Directive 2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC.