SDC Electric Strikes, Magnetic Locks, Electric Door Locksets
Installation Guide for SDC models including: 1291AHDMR, 1291AHDMR Concealed Mortise Bolt Lock, 1291AHDMR, Concealed Mortise Bolt Lock, Mortise Bolt Lock, Bolt Lock, Lock
File Info : application/pdf, 5 Pages, 275.67KB
DocumentDocumentSECURITY DOOR CONTROLS WWW.SDCSECURITY.COM [t] 800.413.8783 805.494.0622 E-mail: service@sdcsecurity.com 801 Avenida Acaso, Camarillo, CA 93012 PO Box 3670, Camarillo, CA 93011 INSTALLATION INSTRUCTIONS 1291AHDMR (.865" BACKSET) CONCEALED MORTISE BOLT LOCK with MECHANCIAL RELEASE FAIL-SECURE (SINGLE CYLINDER PREP) ALUMINUM FRAME PREPARATION .865 3/4" (8X) TAP TABS FOR #10-32 1-1/8" CYLINDER (NOT INCLUDED) Use standard straight cam ILCO (863G) or equivalent. 1-3/4" Ø1-1/4" 11-5/8" Once the Key Cylinder is installed. Secure the cylinder within the guided cylinder slot using the Cylinder Locking Set screw. 10-1/2" Cylinder Locking Set Screw DOOR PREPARATION 1-1/2" 1-1/2" 3/4" (2X) TAP FOR #10-32 4" NOTE: NOT TO SCALE. DIMENSIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. CL OF BOLT 1-1/2" TECHNICAL DATA (FOR STANDARD UNIT) 1/8" FACE PLATE: STRIKE: ID REQUIREMENTS: BOLT: BOLT THROW: BACK SET: 10-1/2" x 1-1/2" X 1/8" 4" x 1-1/2" x 1/8" 10-1/2" x 1-1/2" x 1-3/4" 5/8" DIA. STAINLESS STEEL 3/4" .865" 3-1/4" 4" CL OF DOOR P:\INST INSTRUCTIONS\BOLT LOCKS\INST-1291AHDMR REV F 02-25 Page 1 5-1/4" 10-1/2" FACE PLATE CL 3" STRIKE CL 2" (2x) 5/16" 7-5/8" 4" (2x) 3/4" Any suggestions or comments to this instruction or product are welcome. Please contact us through our website or email engineer@sdcsecurity.com SECURITY DOOR CONTROLS WWW.SDCSECURITY.COM [t] 800.413.8783 805.494.0622 E-mail: service@sdcsecurity.com 801 Avenida Acaso, Camarillo, CA 93012 PO Box 3670, Camarillo, CA 93011 HOLLOW METAL FRAME PREPARATION .865 3/4" (8X) TAP TABS FOR #10-32 1-1/8" CYLINDER (NOT INCLUDED) 1-3/4" Ø1-1/4" 11-5/8" 10-1/2" Once the Key Cylinder is installed. Secure the cylinder within the guided cylinder slot using the Cylinder Locking Set screw. Use standard straight cam ILCO (863G) or equivalent. Cylinder Locking Set Screw DOOR PREPARATION 1-1/2" 1-1/2" 3/4" (2X) TAP FOR #10-32 4" CL OF BOLT NOTE: NOT TO SCALE. DIMENSIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. TECHNICAL DATA (FOR STANDARD UNIT) FACE PLATE: STRIKE: ID REQUIREMENTS: BOLT: BOLT THROW: BACK SET: 10-1/2" x 1-1/2" X 1/8" 4" x 1-1/2" x 1/8" 10-1/2" x 1-1/2" x 1-3/4" 5/8" DIA. STAINLESS STEEL 3/4" .865" 1-1/2" 1/8" 3-1/4" 4" CL OF DOOR P:\INST INSTRUCTIONS\BOLT LOCKS\INST-1291AHDMR REV F 02-25 Page 2 5-1/4" 10-1/2" FACE PLATE CL 3" STRIKE CL 2" (2x) 5/16" 7-5/8" 4" (2x) 3/4" SECURITY DOOR CONTROLS WWW.SDCSECURITY.COM [t] 800.413.8783 805.494.0622 E-mail: service@sdcsecurity.com 801 Avenida Acaso, Camarillo, CA 93012 PO Box 3670, Camarillo, CA 93011 DOOR PREPARATION .865 3/4" (8X) TAP TABS FOR #10-32 1-1/8" CYLINDER (NOT INCLUDED) 1-3/4" Ø1-1/4" 11-5/8" Once the Key Cylinder is installed. Secure the cylinder within the guided cylinder slot using the Cylinder Locking Set screw. 10-1/2" Use standard straight cam ILCO (863G) or equivalent. Cylinder Locking Set Screw FRAME PREPARATION 1-1/2" 1-1/2" 3/4" 4" 3-1/4" 4" (2X) TAP FOR #10-32 NOTE: NOT TO SCALE. DIMENSIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. CL OF BOLT 1-1/2" TECHNICAL DATA (FOR STANDARD UNIT) 1/8" FACE PLATE: STRIKE: ID REQUIREMENTS: BOLT: BOLT THROW: BACK SET: 10-1/2" x 1-1/2" X 1/8" 4" x 1-1/2" x 1/8" 10-1/2" x 1-1/2" x 1-3/4" 5/8" DIA. STAINLESS STEEL 3/4" .865" CL OF STRIKE P:\INST INSTRUCTIONS\BOLT LOCKS\INST-1291AHDMR REV F 02-25 Page 3 5-1/4" 10-1/2" FACE PLATE CL 3" STRIKE CL 2" (2x) 5/16" 7-5/8" 4" (2x) 3/4" SECURITY DOOR CONTROLS WWW.SDCSECURITY.COM [t] 800.413.8783 805.494.0622 E-mail: service@sdcsecurity.com 801 Avenida Acaso, Camarillo, CA 93012 PO Box 3670, Camarillo, CA 93011 INSTRUCTIONS FOR REVERSING THE MOUNTING BLOCK Remove the Cylinder locking set screw, and screw the Cylinder out of the Mounting Block. Remove the four screws securing the Mounting Block and the Sliding Link Block. Cylinder Locking Set Screw Mounting Block Sliding Link Block Make sure the sliding Link Block is positioned properly Reverse the components and re-install as shown. P:\INST INSTRUCTIONS\BOLT LOCKS\INST-1291AHDMR REV F 02-25 Page 4 SECURITY DOOR CONTROLS WWW.SDCSECURITY.COM [t] 800.413.8783 805.494.0622 E-mail: service@sdcsecurity.com 801 Avenida Acaso, Camarillo, CA 93012 PO Box 3670, Camarillo, CA 93011 LOCK WIRING Select 24VDC OR 12VDC Configuration, and use provided pigtail connector: 24VDC SOLENOID CONFIGURATION Access Control or Push Button (N/O) (N/C) FROM LOCK (PRE-WIRED) PIGTAIL CONNECTOR RED (+) N/O ORG BLK Cap unused wires BLU WHT (-) COM (+) 24VDC (-) POWER INPUT 12VDC SOLENOID CONFIGURATION FROM LOCK (PRE-WIRED) PIGTAIL CONNECTOR RED (+) BLK ORG BLU WHT (-) Access Control or Push Button (N/O) (N/C) N/O COM (+) 12VDC (-) POWER INPUT Dual Voltage Solenoid: 12VDC @ .9 Amp (Max) Continuous Duty 24VDC @ .45 Amp (Max) Continuous Duty ARS DPS Electrical Data OPTIOINAL BOLT POSITION SENSOR (BPS-MAGNETIC) B Indicates bolt locked or unlocked 5 Watt OPTIOINAL DOOR POSITION SWITCH (DPS-MECHANICAL) D Indicates door opened or closed 4A @ 30VDC (Resistive) * When both options are ordered the Common is shared. DPS / BPS CONFIGURATION * BPS polarity shown with bolt retracted. YELLOW / BLACK = N/O ORANGE / BLACK = N/C WHITE / BLACK = COM BPS YELLOW / RED = N/O ORANGE / RED = N/C WHITE / BLACK = COM * DPS polarity shown with door closed. P:\INST INSTRUCTIONS\BOLT LOCKS\INST-1291AHDMR REV F 02-25 Page 5