BRASQ Pedestal Fan with Remote F100 Black Ø 40 cm

Thank you for your purchase

Thank you for purchasing this fan. Please read all instructions carefully and keep for future use. In this manual you will find instructions in the following languages: EN, NL, PL, DE and PO.

Product Information: 8582601 BRASQ Pedestal fan with remote F100 black Ø 40 cm, 8719324152600

Important Safety Instructions

Read this manual thoroughly before first use, even if you are familiar with this type of product. The safety precautions enclosed herein reduce the risk of fire, electric shock and injury when correctly adhered to. Make sure you understand all instructions and warnings. Keep the manual in a safe place for future reference, along with the completed warranty card, purchase receipt and carton. If you sell or transfer ownership of this product, pass on these instructions to the new owner.

Always follow basic safety precautions and accident prevention measures when using an electrical appliance, including the following:

• Electrical safety and cord handling
• Voltage: Make sure your outlet voltage and circuit frequency correspond to the voltage stated on the appliance rating label. If this is not the case, do not use the fan.
• Water: To protect against fire and electric shock, do not immerse the cord, plug or the fan itself in water or other liquid, or expose the electrical connections to water. Ensure your hands are dry before handling the plug or switching on the appliance. Do not use the fan outdoors or on wet surfaces. Protect it from liquid spills.
• Damage: Check the power cord regularly for visible damage. If the cord is damaged, it must be replaced by the manufacturer, its authorised service centres or appropriate qualified personnel in order to avoid any hazards.
• WARNING! Do not pick up or operate the appliance if the power supply cord, plug or housing is damaged, or after it malfunctions or has been dropped or damaged in any manner. In case of damage, contact our after sales support line for advice.
• Protect the power cord:
  • Do not operate the fan with the cord coiled up; always fully unwind.
  • Do not twist or kink the cord or let it touch heated surfaces.
  • Do not put any stress on the cord where it connects to the product. Never carry the fan by the cord.
  • Arrange the cord away from any traffic area so no one will trip over it.
  • Do not run the cord under carpeting or cover it with rugs or runners.
• WARNING! No extension cord, no timer: Do not use this fan with an extension cord, plug adaptor, external timer or separate speed control device.
• Connection: To insert the plug, grasp it firmly and guide it into outlet.
• Disconnection: Unplug the appliance from the power outlet when it is not in use and before cleaning, servicing, moving or storing the appliance. Grasp the plug and remove it from the outlet, do not pull the cord when disconnecting.

Disposal Information

This appliance should not be put into the domestic garbage at the end of its useful life, but must be disposed of at a central point for recycling of electric and electronic domestic appliances. This symbol on appliance, instruction manual and packaging puts your attention to this important issue. The materials used in this appliance can be recycled. By recycling used domestic appliances you contribute an important push to the protection of our environment. Ask your local authorities for information regarding the point of recollection.

Product Overview

The product includes the following parts:

• 1 Front guard
• 2 Clip
• 3 Spinner
• 4 Blade
• 5 Nut
• 6 Rear guard
• 7 Shaft
• 8 Oscillation pin
• 9 Motor
• 10 Switch box
• 11 Screw B
• 12 Extension pole
• 13 Base tube
• 14 Base cover
• 15 Screw A
• 16 Round base
• 17 Remote control

Diagram Description: The diagram shows an exploded view of the pedestal fan, with numbered parts corresponding to the parts list. The fan consists of a base, a telescopic stand, a motor housing with controls, and the fan head with guards and blades.

Remote Control

The remote control has the following buttons:

• 1. OFF Button
• 2. SPEED/ON Button
• 3. TIMER Button
• 4. MODE Button

Getting Started

Unpacking

• This product has been packaged to protect it against transportation damage. Unpack the appliance and keep the original packaging carton and materials in a safe place. It will help prevent any damage if the product needs to be transported in the future. In the event it is to be disposed of, please recycle all packaging materials where possible.
• Plastic wrapping can be a suffocation hazard for babies and young children, so ensure all packaging materials are out of their reach and disposed of safely.
• Unwind the cord to its full length and inspect it for damage. Do not use the appliance if the appliance or its cord have been damaged or are not working properly. In case of damage, contact our after sales support line for advice on examination, repair or return of the damaged product.
• Read the manual to familiarise yourself with the parts and operating principles. Pay particular attention to the safety instructions on the previous pages.

Remote control preparation

• For remote control operation, insert two AAA size batteries into the remote control. Slide out the battery cover with your thumb on the mark at the back of the remote control. Insert the batteries following the polarity symbols (+/-), then replace the cover to the battery compartment.
• When replacing batteries, always replace all batteries with new ones of the same size and type. Do not mix old and new batteries. Do not mix alkaline standard (carbon-zinc). or rechargeable (nickel-cadmium) batteries.
• If the remote control will not be used for a long period of time, remove the batteries from the battery compartment to avoid leakage which can damage the remote control.

Assembly

Base Assembly

• Put the end bottom of the outer tube into the centre hole of the base and fix it tightly with the screws and nuts.

Fan Motor Assembly

• Connect the motor and switch box with the inner tube and fix them using the screw. To adjust the height, loosen the height adjustment screw, slide the inner tube to the desired height and tighten again.

Rear Guard Assembly

• Put the rear guard on the front motor housing guides, fix it tightly by turning the nut clockwise.

Fan Blade Assembly

• Push the fan blade on the motor shaft. Secure the fan blade with the blade cap, turning anti-clockwise to tighten.

Front Guard Assembly

• Attach the front and rear guard firmly by locking the clips, make sure the safety screw is fixed with the nut.

Instructions

This fan is equipped with 3 speeds, 3 breeze modes, a timer and a remote control. For your convenience, the buttons on the control panel of the fan operate the same functions as the remote control.

Set the fan on a dry, level surface, plug it into a 220-240V 50Hz electrical outlet and follow the operating instructions below.

ON/SPEED

• Press this button to switch on the fan.
• When the unit is switched on, press this button to change the fan speed through three comfort speeds: Low, Medium or High.
• The speed can be adjusted in all modes.

SWING

• Press this button on the product to swing the product.

MODE

• Press this button to change the fan mode through different breeze modes.
• Normal: In this mode the fan operates at a constant speed.
• Nature: In this mode the fan simulates a natural breeze mode by cycling on and off, as in nature.
• Sleep: In this mode the fan simulates a soft, gentle breeze mode, starting with a strong breeze and then gradually reducing the breeze to medium and then low before repeating this cycle.

TIMER

• Pressing this button sets the timer in increments of 0.5 hour to a maximum of 7.5 hours. After the timer runs out, the fan will automatically shut off.
• There are four indicator lights for the timer: 0.5h, 1h, 2h, 4h.

OFF

• Press this button to switch off the fan.

Tilting the fan head

• The fan head can be tilted so that the breeze is targeted at an angle. To tilt the fan head, make sure the fan is disconnected from the power supply.
• Slightly loosen the tilt screw. Steady the motor housing of the fan with one hand and grip the fan grille with the other. Carefully tilt the fan head until it reaches the desired angle.
• CAUTION: Do not tilt back the fan head further than it is intended to go. Doing so will damage the unit.