REHAU ABS/PVC Edgeband Standard Tolerances
This document outlines the standard tolerances for REHAU ABS/PVC edgebands, providing essential specifications for width, thickness, preliminary tension, plane parallelism, and longitudinal warpage.
Width Tolerances
Standard tolerances for ABS/PVC edgebands concerning width.
| Width (mm) | Tolerance (mm) |
|---|---|
| 10.00 - 17.00 | 0.50 |
| 17.01 - 33.00 | 0.50 |
| 33.01 - 45.00 | 0.50 |
| 45.01 - 75.00 | 0.80 |
| 75.01 - 104.00 | 0.80 |
Thickness Tolerances
Tolerances for edgeband thickness.
For Thickness ≤ 1mm
| Thickness (mm) | Tolerance (mm) |
|---|---|
| ≤ 1.00 | ±0.50 |
For Thickness > 1.01mm
| Thickness (mm) | Tolerance (mm) |
|---|---|
| 1.01 - 1.60 | ±0.20 |
| 1.61 - 2.70 | ±0.30 |
| 2.71 - 4.00 | ±0.40 |
Preliminary Tension (Edge Bow) Tolerances
Tolerances for preliminary tension (edge bow) based on width and thickness.
| Width (mm) | Tolerance for Thickness ≤ 2.00mm (max.) | Tolerance for Thickness > 2.00mm (max.) |
|---|---|---|
| 10.00 - 17.00 | 0.15 | 0.20 |
| 17.01 - 23.00 | 0.20 | 0.25 |
| 23.01 - 33.00 | 0.30 | 0.30 |
| 33.01 - 75.00 | 0.60 | 1.00 |
| 75.01 - 104.00 | 1.50 | 2.00 |
Plane Parallelism Tolerances
Tolerances for plane parallelism.
| Thickness (mm) | Width Range (mm) | Tolerance (max. mm) |
|---|---|---|
| 0.40 | 10.00 - 33.00 | 0.05 |
| 4.00 | 33.01 - 45.00 | 0.10 |
| 4.00 | 45.01 - 104.00 | 0.15 |
Longitudinal Warpage Tolerances
Tolerances for longitudinal warpage under specified conditions.
| Thickness (mm) | Tolerance (max. mm / 2m) | Measurement Condition |
|---|---|---|
| 0.40 - 0.80 | 20 mm / 2 m | Free-storage / without tension |
| 0.81 - 1.70 | 10 mm / 2 m | Free-storage / without tension |
| 1.71 - 4.00 | 8 mm / 2 m | Free-storage / without tension |
Notes and Disclaimers
For special dimensions, the relevant drawing will be valid.
This document is protected by copyright. All rights reserved. No part of this publication may be translated, reproduced, or transmitted in any form or by any means without prior written consent. REHAU's application-related advice, both verbal and written, is based on years of experience and standardized assumptions and is provided to the best of its knowledge. The intended use of REHAU products is described in the technical product information, available at www.rehau.com/TI. Application, use, and processing of the products are outside REHAU's control and are the sole responsibility of the respective user. Liability, if any, is governed exclusively by REHAU's terms and conditions, available at www.rehau.com/conditions, unless otherwise agreed in writing. This applies to warranty claims as well, with the warranty covering the consistent quality of REHAU products according to specifications. Subject to technical changes.
Contact Information:
REHAU Industries SE & Co. KG
Helmut-Wagner-Straße 1
D-95111 Rehau
www.rehau.com
Document Version: FS-D+P-TECH H. Affeldt 1472 / H. Hacker 2348, Stand 07.2025
