U13 WiFi Extender Quick Installation Guide

Panel Layout

LED Explanation:

• Red: Power indicator
• Blue Blinking: WPS connection in process (up to 2 minutes)
• Green Blinking: Extender connected to the Internet
• Orange Solid: Router connected to Host router, but too far
• Green Solid: Router connected to router, in a good location
• Green Blinking (LAN/WAN): Device connected to router's LAN/WAN port
• Off (LAN/WAN): No device connected to router's LAN/WAN port

Button and Port Explanation:

• Reset Button: Press and hold for more than 5 seconds to reset to factory defaults.
• WPS Button: Press to enable WPS function.
• LAN Port: For connecting to a DSL/Cable modem or Ethernet jack.
• WAN Port: For connecting to a DSL/Cable modem or Ethernet jack.
• LAN/WAN port: For connecting to a DSL/Cable modem or Ethernet jack.

WiFi Repeater Mode

In this mode, the extender boosts existing wireless coverage.

Relocate

1. Plug the extender into an electrical outlet between your router (Host Network) and the Wi-Fi "dead" zone.
2. The chosen location must be within the range of your existing host network.
3. Wait until the LED is lit and solid Green. If not, relocate it closer to the router for better signal quality.

Configuration Methods:

Method ONE: Using WPS (Wi-Fi Protected Setup)

Recommended if your host router has a WPS button.

1. Press the WPS button on your router.
2. Within 2 minutes, press the WPS button on the extender for 1 second.

Wait for the LED to be Solid Green. You can find network names with "_EXT" in your phone's Wi-Fi list, indicating a successful WPS connection. If not, use Method Two.

Method TWO: Using a Web Browser

For Mobile phone users:

1. Find the SSID (Network Name) printed on the label of the U13 router.
2. Connect your mobile phone to the U13 router's network (e.g., "Extender-a4f97c").
3. Open a web browser and navigate to http://192.168.11.1.
4. Follow the on-screen instructions to select Repeater mode, enter your Host router's password, and complete the configuration.

Network Names: Extended Network Names will be your Host Router's network name with "_EXT" at the end. Passwords will be the same as your host network.

AP Mode

In this mode, the router transforms your existing wired network into a wireless one.

1. Connect your router to the U13's LAN/WAN port using an Ethernet cable.
2. Connect your mobile phone to the U13 router's network (e.g., "Extender-a4f97c").
3. Open a web browser and navigate to http://192.168.11.1.
4. Select AP mode and click next.
5. Set the WiFi password (e.g., 88888888) or customize it.
6. Click NEXT and follow the prompts to complete the configuration.

Router Mode

This mode allows the extender to function as a standalone router.

1. Hardware Connections:
• If your internet connection is through a DSL/Cable modem, connect it to the U13's LAN/WAN port.
• If your internet connection is through an Ethernet cable from the wall, connect it to the U13's LAN/WAN port.
2. Connect your mobile phone to the U13 router's network (e.g., "Extender-a4f97c").
3. Open a web browser and navigate to http://192.168.11.1.
4. Select Router mode and click next.
5. Set up Your Internet Connection: Choose Internet Type (Dynamic IP, Static IP, or PPPoE) and enter the required information provided by your ISP.
6. Set the SSID (e.g., "Extender-a4f97c") and WiFi Password, or customize them.
7. Click NEXT and follow the prompts to complete the Router mode configuration.

Connect to the extended network (default SSID and password) and enjoy internet access.

Frequently Asked Questions (FAQ)

Q1. What can I do if the login window does not appear?

• Ensure your computer is set to obtain an IP address automatically.
• Verify that http://192.168.11.1 is entered correctly in the web browser.
• Make sure your computer is connected to the Mini Router's network.
• Try a different web browser or reboot your router.
• Disable and re-enable your network adapter.

Q2. What can I do if I cannot access the Internet?

• Check if the internet is working by connecting a computer directly to the modem via Ethernet cable. Contact your internet provider if it's not.
• Reboot your router and try again.

Q3. How do I restore the router to its factory default setting?

While the router is powered on, press and hold the reset button on the rear panel for approximately 5 seconds.

Q4. Why is setting the repeater mode unsuccessful?

• You may have typed the router's wireless password incorrectly. Log in and check it.
• The Mini router may be out of range. Move it closer to the router.
• Reset the Mini Router and go through the configuration again.
• To reset the extender, press and hold the reset button inside the tiny hole for 10 seconds.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.